Search Documents

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By Z. M. Zhang

Fracture grouting is a particular technique which can be used in soils and rocks with low permeability to increase groutability and penetration rates and to solve some special foundation problems by inducing limited and controlled zones of hydrofracture surrounding the injection source. The present paper describes the basic principles of hydrofracture and its application to grouting in deep foundations, and indicates some recognitions about the mechanisms and effects of fracture grouting.

Jan 1, 2010

By J A. H Campbell

AK6 is a Cretaceous aged kimberlite located in the north-east of Botswana, close to Debswana's Drapa and Letlhakane Mines. It was discovered by Debswana in 1969, but was considered unattractive from an economic perspective. In 2003, Debot Prospecting Pty Ltd ('Debot') re-assessed the area and with the advent of new prospecting technology, particularly large diameter drilling ('LDD') and more detailed ground geophysical surveys found AK6 to be of interest. In 2005, the Boteti joint venture was formed between Debot and African Diamonds plc ('AFD'), which covered a number of Prospecting Licenses, including that which contained AK6.

Jan 1, 2010

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By Jonguk Kim

Submarine hydrothermal activity and mineralization related to island arc volcanism along the Tonga arc were explored during two research cruises in October 2009 (KODOS 09H) and February 2010 (KODOS 10H), respectively. In KODOS 09H cruise, geophysical survey, including multi-beam bathymetry, marine seismic and magnetic investigations, was performed on 10 volcanoes to find out possible structural discontinuity that can act as fluid pathway for formation of hydrothermal deposits at submarine caldera system. The result provided acoustic and seismic image maps and magnetic anomaly maps of targeted volcanoes. Then, detailed seafloor observation and sampling as well as deep tow side scan sonar survey were performed in KODOS 10H cruise on 5 volcanoes which are selected as targeted areas from the previous cruise. Among 5 targeted volcanoes, TA26 shows most extensive hydrothermal activity. Hydrothermal vents and alteration zone were observed on western caldera and summit of eastern cone of the TA26. Although only weak hydrothermal alteration was observed on eastern cone, mineralized fragments of chimney and mound were sampled from western wall of central caldera on TA25 volcano. On TA12 volcano, strong hydrothermal plume and alteration zone was detected during video tows operated between SW scoria cone and small ridge. However, only small amount of hydrothermal altered rocks were collected from TA12. Although hydrothermal activity and mineralization might be formed, supported by plume detection and result of geophysical survey, only weak alteration zones were observed on other two volcanoes (TA19 and TA22). The exploration area generally show shallow depth up to several tens of meters on summit where subsurface boiling of hydrothermal fluid might occur due to low hydraulic pressure, which can affect on styles of hydrothermal venting and mineralization process observed on Tonga submarine arc volcanoes.

Jan 1, 2010

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By F. C. Grensing, W. R. Crib

Copper-15 Nickel-8 Tin alloy is a relatively modern material, having been discovered in the 1970’s. It has complexities with casting, hot working and interdependent solid state phase transformations. A key to the high reliability manufacture of wrought rods, bars, plates and tube is the casting technology, which limits segregation, promotes microstructural uniformity and enables hot working. The EquaCast® continuous casting process has enabled the production of a broadening variety of wrought forms with typical yield strengths ranging from 100 to 180 ksi (690 to 1241 MPa) depending on size, shape and temper. This paper reviews the characteristics of wrought Copper-15 Nickel-8 Tin products which have registration in AMS specifications (4596 and 4597) and MMPDS-04 (CN-1) for use in aircraft. The design limits, microstructures, fracture characteristics and tribological behavior will be examined. This alloy system is emerging as a material of choice for aircraft bearings, corrosion resistant oil and gas exploration components, machinery and demanding off-road equipment applications. ToughMet® 3 is an alternative or upgrade to conventional moderate and high strength aluminum bronze bearing alloys.

Jan 1, 2010

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010