Search Documents

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

Copper Recovery from Printed Circuit Board by Carbonisation

Sep 13, 2010

Several Approaches to Enhance the Bioleaching of Enargite Some approaches were investigated to enhance the recovery of Cu from enargite by bioleaching with Acidithiobacillus ferrooxidans using the galvanic interaction with pyrite and activated carbon, and with thermophilic bacteria, Acidianus brierleyi. Addition of pyrite initially enhanced Cu leaching by the Galvanic effect, but after that the formation of secondary minerals passivated the surface of enargite in inoculated batches. Activated carbon improved Cu recovery from enargite much better than pyrite, when it is contacted with enargite. Recovery of Cu from enargite has been recorded to at largest 2.4 per cent within 30 days in the presence of activated carbon when mesophilic bacteria were inoculated at 25¦C. The recovery of Cu from enargite was drastically enhanced by inoculation of thermophilic bacteria, Acidianus brierleyi, up to 60 per cent within 40 days at 70¦C and still not leveled off after 40 days unless the formation of Fe(III) precipitates occurred. After 40 days dissolved molar ratio of Cu/As is around 5.2, suggesting that metal-deficient sulfides and/or ferric arsenate might be formed on the surface of enargite.

Sep 13, 2010

Grinding and Beneficiation Characteristics of a Low-Grade Haematite Ore

Sep 13, 2010

Characterisation of Computer Printed Circuit Boards for Hazardous Properties and Beneficiation Studies

Sep 13, 2010

Study on Mechanism of Sphalerite Flotation in the Presence of Main Metal Ions by Molecular Mechanics

Sep 13, 2010

Pilot-Plant Testing of Ammoniacal-Cyanidation for Gold Recovery from Copper Gold-Bearing Ore The results of pilot-plant tested ammoniacal-cyanidation of gold recovery from copper gold-bearing ore are presented in this paper. This ore is from a deposit of Russian Federation with gold and copper grade 9.5 g/t and 0.4 per cent, respectively. Copper is largely present as malachite and azurite. The presence of chalcopyrite and bornite is also observed. In order to recover gold, gravity is recommended. Two options of ammoniacal-cyanidation using leaching of gravity tails, CIP and filtration, were tested. It was found that ammoniacal-cyanidation using filtration of leaching tailings and recycled solutions is the most optimal option. The proposed flow sheet provides for 89.7 per cent gold recovery from gravity tailings at the consumption of NaCN 0.9 kg/t and (NH4)2CO3 7.5 - 9 kg/t. Compared to conventional cyanidation, this technology decreases the consumption of sodium cyanide from 4 up to 0.9 kg/t at the same gold recovery. It can be recommended for the treatment of copper gold-bearing ores with the similar composition.

Sep 13, 2010

Two Variable Real-Time Algorithm for Cone Crusher Control

Sep 13, 2010

The Detachment of Coarse, Composite Particles from Bubbles

Sep 13, 2010

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

Certain Molybdenum Resources in Indonesia Mineralogical and Processing Study

Sep 13, 2010

The Effect of High Power Nanosecond Electromagnetic Pulses on Selectivity of Pyrite from Arsenopyrite

Sep 13, 2010

Study on Preparation and Gel Performance of High Purity Montmorillonite In order to research the colloidal and thixotropic performance of the inorganic gel prepared by high purity montmorillonite, this study uses the moderate grade bentonite ores from Weifang (China) as raw material. Two-stage hydrocyclone classification was applied to obtain the high purity montmorillonite with its content of 94.8 per cent. In contrast to other methods of montmorillonite purification, two-stage purification by hydroclone has the advantages of larger throughput and easily achieving auto-control in industry, and purified products with different montmorillonite content can be obtained by this method. And then the inorganic gel was prepared by the prepared high purity montmorillonite and its colloidal and thixotropic performances by measuring the flowability and thixotropy were further studies. Research results show that the inorganic gel has plastic body liquidity, the viscosity decreases with the increase of the shear rate, the static and dynamic shearing stress values are 33.98 Pa and 91.89 Pa, respectively, and the thixotropic value is 95.2 dyne+s/cm2, which indicates that it has preferable colloidal and thixotropic performance. Montmorillonite inorganic gel prepared by bentonite with high montmorillonite content and low-layer charge has better gel performance.

Sep 13, 2010

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

Coal Preparation Research at Turkish Coal Enterprises (TKI)

Sep 13, 2010

Iron Concentrate Synthesised from Waste Ferrous Sulfate Produced in Titanium White Preparation

Sep 13, 2010

Possibilities for Flotation Acoustics Monitoring - A Review

Sep 13, 2010

Discrete Element Method - Computational Fluid Dynamics Modelling of Flow Behaviour in a Stirred Mill - Effect of Operation Conditions

Sep 13, 2010

A New Cell for Electrochemically Aided Flotation

Sep 13, 2010