Search Documents

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By P Andersson, P Marklund

Evaluation of different techniques for bottom fill stabilisation showed that frozen fill was the most economical method. In order to test the method a full-scale field test was performed in the Rehnstr÷m mine. The test was instrumented with temperature gauges and extensometers. Before the field test, frozen fill was tested at the laboratory. The mechanical properties of the frozen fill were determined by uniaxial compression and creep tests. A deformation model for the frozen fill was set up. Calculation procedure for design of spacing between the freezing tubes, time for freezing and calculation of the necessary capacity of the refrigeration plant was developed. These procedures were calibrated against the field test. The results of these investigations allow the following conclusions: From a mechanical point of view, frozen fill has excellent properties as a structural member and it also has excellent properties to support itself and the fill above. Methods for the thermal and mechanical design of freeze stabilisation have been developed and found adequate. The need to place the freezing tubes several years in advance of the future sill pillar mining, requires careful long-term planning and accurate documentation.

Jan 1, 1998

A wide range of materials are used in hydraulic backfilling operations and the pipeline flow behaviour of these mixtures varies considerably. It is shown that despite the large differences in constituent materials and flow behaviour, a common approach can be applied to analysing the flow of all hydraulic backfills. This is extended to include a rational design approach for backfill distribution systems. The use and limitations of pipe loop tests as a design aid is discussed. Backfill quality control is identified as a key area where improvement needs to be made to enhance the reliability of backfill system operation.

Jan 1, 2001

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By J Hudson

Autogenous (AG) and Semi Autogenous (SAG) grinding mills are the conventional selection for large-scale grinding circuits. It is accepted that these forms of comminution are not the most energy efficient available. This efficiency combined with escalating energy prices, steel prices and the requirement to process larger, lower grade deposits has necessitated that better comminution techniques are found to challenge the dominant position of AG/SAG mills in the grinding circuit. Recent advances in high pressure grinding rolls (HPGR), particularly in terms of roll surface protection have meant that, depending on the application, an economic alternative is available to the large diameter AG/SAG mills. Mining companies now recognise the potential benefits of HPGR and so they need proper assessment in the design of new or upgrade of existing grinding processes. Of course, the answer to the question AG/SAG or HPGR is not straightforward and the impact of the grinding process on the whole metallurgical process needs to be evaluated. Clearly this is a complex decision to make and requires substantial metallurgical knowledge, test work, and objective analysis. The perceived downstream processing benefits will differ between different plants depending on the ore type and processing conditions. The optimal design of the comminution circuit requires that a robust methodology is followed to objectively characterise the ore, size the equipment and determine the downstream processing benefits. The paper gives a brief comparison of the capital and operating costs for both grinding systems, and then outlines the appropriate test work that is required to make an informed decision.

Jan 1, 2006

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005

By Rimas Pakalnis, Ted Williams, Tom Brady, Wilson Blake, Mary MacLaughlin, Kathryn Clapp, Cristian Caceres, Mario Morin

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten (10) mines throughout North America. It outlines areas of concern in terms of design requirements.

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in &apos;good&apos; ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By A Kemp, I Taylor, S C. Lamoureux

Detailed landform designs were completed for six (integrated) iron ore waste rock dumps at a Western Australian iron ore mine site to meet closure objectives and to optimise material movements for closure. The designs were based on specific physical and geochemical properties of waste material and the design was undertaken to enhance long-term stability of the dumps and optimise material movements, and therefore minimise closure cost. Construction of the re-shaped waste rock dumps have been completed. Following construction, surface material characteristics were found to deviate from those used in the design assessment. Materials present at surface following re-shaping were generally finer textured than those sampled for modelling. It is anticipated that the embankment slopes may experience increased rates of surface erosion compared to the rates predicted from modelling and used in design. The finer textured material is thought to be generated from exposing finer material that has migrated into the coarser matrix over time or that was not present in the sampled top surface of the landforms. This is due to armouring processes over time and this phenomenon is likely to recur following further wet seasons. The majority of the waste materials present in the waste rock dumps were subgrade banded iron formations (BIF) and chert, which are generally competent and geochemically inert. Some waste material was known to have an elevated risk of erosion but present in relatively small quantities. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert). This paper presents the process from upfront materials assessment through detailed design to construction of the rehabilitated waste rock dumps, and post-construction sampling and testing to validate model findings.CITATION:Kemp, A, Taylor, I and Lamoureux, S C, 2017. Design to closure – construction of detailed rehabilitation designed iron ore waste rock dumps based on upfront site specific assessment, in Proceedings Iron Ore 2017, pp 353–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017