Search Documents

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By Donald E. Archibald, Gerald A. Allcott

"Noranda's Heath Steele Mine is located 35 miles north of Newcastle in northern New Brunswick. Blasthole open stoping with partial delayed filling is the major mining method in use. The selection of stope and pillar dimensions to ensure mine stability was originally subjective. This paper describes the progress made in attempting to rationalize design.One major feature is the fracture pattern. The main orebody now being mined, the B zone, has undergone five periods of folding and each period of folding developed a family of fracture planes which are axial planar to that particular fold pattern.The other major features considered are the calculated increase in stress due to mining and depth and its relationship to measured strain. Experience has shown that ground problems affecting production have usually originated in rib pillars. Field observations of ground deterioration and multi-wire extensometer measurements of strain are tabulated together chronologically for each pillar.A factor representing stress and a common plane of weakness are identified. Graphical analysis is used to determine the effect of the plane of weakness on a typical stress/strain curve and provides a base for the design of pillars."

Jan 1, 1981

By R. Canello, J. Jenkins

El Abra has the world's largest leach, solvent extraction and electrowinning facility, The crushing plant capacity is 120,000 metric tonnes per day and the cathode production capacity is 225,000 metric tonnes per year. The El Abra mine and plant are located in the Province of El Loa, in Region I1 of Chile, 55 km. north of the city of Calama. The ore deposit outcrops on the southern slope of Cerro Pajonal at an altitude of 3,900 to 4,100 meters above sea level. The processing plant and camp facilities are located at a lower 3,300 meter elevation on an alluvial slope, 15 km southeast of the deposit. The operating company, Sociedad Contractual Minera El Abra, is 51% owned by Cyprus Arnax Minerals Company through the Cyprus Climax Metals Company subsidiary and 49% owned by Corporaci6n Nacional del Cobre de Chile (Codelco). The present paper describes the ore reserves, mine operations, crushing, leaching, solvent extraction, electrowinning and infrastructure facilities.

Jan 1, 1998

THE plant is one of the usual type of Mond plants, and contains no new features worthy of comment. A brief description of the process, however, with a few remarks on the working of the plant, may prove of interest.Producer gas is made by passing a mixture of air and steam through incandescent carbon contained in a furnace called a producer, which, in the Mond type, is a cylindrical casing of steel plate, lined with firebrick, and fitted at the lower end with sloping fire-bars'. Coal crushed to an even size (about 2-in. gauge) is elevated to bunkers over the producers, from which it is fed into a measuring hopper on each producer.The hopper is a cast-iron cylinder fitted with a swing cover at the top and a bell valve at the bottom, worked by a lever and balance weight. When a charge of coal is run from the bunker into the hopper, the cover is closed, and the bell valve is lowered, allowing the coal contents to drop into the producer. Thus no gas can escape from, or air be admitted to, the producer during the process of charging. The hopper discharges its coal through a steel pipe-shaped container called the bell, which projects about 9 in. through the roof of the producer. The function of the bell is to spread the coal evenly over the fire, and supply coal to any portion of the fire as it settles.

Jan 1, 1918

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

THE following paragraphs represent an endeavour to describe, briefly the equipment used for the manufacture of sulphuric acid and superphosphates by the Corporation.SULPHURIC ACID PLANTS.Two separate units are in operation, No. I Plant working on sulphur dioxide generated from pyritic ore, No. 2 Plant working on sulphurous gases obtained from the Huntingdon-Heberlein desulphurizing process. The latter plant is unique in being the first installation for the successful use of these gases.

Jan 1, 1918

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

Diamond bearing deposits are extremely low grade and require large bulk samples to be tested to determine the grade and quality of the stones. The semi portable plants, for treatment of these bulk samples, have followed the development of commercial processes for diamond concentration. These processes included jigs and diamond pans, which have been largely supplanted by heavy media processes for primary concentration, due to the higher efficiencies in all size ranges. A number'of flowsheets including these processes are presented. The final recovery of diamonds from the bulk sample concentrates can be accomplished by rejigging, adherance to grease or by X-ray sorting. Flowsheets incorporating all the processes are presented. Two plants are described; one incorporating jigging, rejigging and hand sorting; the other using heavy media separation, and wet X-ray sorting.

Jan 1, 1984

By Robert C. Handfield

The trip from Denver southwest to Gunnison crosses seven main geologic and physiographic areas as shown on the accompanying map. These are: I Mesozoic and Tertiary sedimentary rocks of the Denver Metro area from downtown Denver to the foothills near Morrison. II Precambrian metamorphic and igneous rocks of the Front Range from near Morrison to the west side of Kenosha Pass. III Sedimentary and volcanic rocks of South Park (Paleozoic, Mesozoic and Tertiary) from the west side of Kenosha Pass to Trout Creek Pass. IV Precambrian granitic rocks (1,350-1,480 M.Y.) between Trout Creek Pass and the Arkansas River. V Tertiary and Quaternary sedimentary rocks and sediments of the Arkansas River valley. VI Precambrian metamorphic and igneous rocks and Paleozoic sedimentary rocks of the Sawatch uplift from Maysville to near Doyleville on the west side of Monarch Pass. VII Mostly sedimentary rocks of Cretaceous and Tertiary age from the Doyleville area west to beyond Gunnison. Each area will be elaborated in the following pages but no detailed road log is given since these are available elsewhere. An attempt has been made to point out some deposits and features of interest to economic geologists but it is by no means complete.

Jan 1, 1983

By Filipe Sathler

Mediante efeitos de sazonalidades do mercado Siderúrgico, períodos de crise, aliados às necessidades de reparos de equipamentos, os Altos Fornos são, eventualmente, submetidos ao desligamento. O procedimento específico mais utilizado é o Blowdown, com o abaixamento de carga até nível de ventaneiras, facilitando posterior limpeza e reparo. Para sucesso deste procedimento, é essencial um planejamento adequado das atividades. Informações técnicas e experiências operacionais permitiram o embasamento teórico e a execução do Blowdown do Alto Forno 03 da ArcelorMittal FCSA (Tubarão). Como preparação, foi efetuado o aumento do fluxo periférico (remoção de cascão) e o aumento da permeabilidade do Cadinho (maior circulação de líquidos, limpeza e drenagem). Realizou-se também a preparação de equipamentos específicos e controle dos parâmetros operacionais. O abaixamento de carga foi devidamente realizado conforme planejado, até o nível de ventaneiras e permitindo paredes internas livres de cascões.

Aug 16, 2017

By Miguel Tapia, al et, Milenko Gonzalez, Sergio Giglio

El Encierro es un yacimiento de tipo pórfido Cu-Au del Mioceno superior ubicado en la zona intermedia entre las franjas de El Indio y Maricunga, en el norte de Chile. Está emplazado bajo un extenso lithocap que presenta evidencias de mineralización de tipo epitermal de alta sulfuración y que fue explorado entre 1987 y 2010 por varias empresas. En 2016, AMSA firmó un contrato de opción de compra con Barrick con el objeto de comprobar la existencia de un sistema tipo porfídico en profundidad con potencial económico. Cuatro campañas de perforación desarrolladas entre 2015 y 2020 permitieron probar que debajo del lithocap se encuentra un sistema porfídico de Cu-Au con leyes que se incrementan por debajo de la cota 3,000 m.

May 10, 2023

By Fernando Llosa

El presente trabajo describe el origen y la geología del proyecto Trapiche, como propiedad de la Cía. El Molle Verde SAC subsidiaria. Dicho proyecto está ubicado 100 km al sur de la ciudad de Abancay, región de Apurímac, parte central del sur Perú y fue descubierto por Cedimin, producto de un intenso programa de grassroot realizado a partir del año 1995 hasta el 2001 en que fue perforado. Luego fue explorado por Cía. de Minas Buenaventura a partir del 2,005 hasta la actualidad. El yacimiento es del tipo pórfido de cobre y molibdeno, su localización metalogenética es en el borde oeste del batolito Andahuaylas – Yauri, de composición calco-alcalina con presencia de pórfidos activos, que están intruyendo sedimentos clásticos – carbonatados del Jurásico – Cretáceo. En dicho "belt" se emplazan importantes yacimientos tipo pórfido y skarn de cobre y molibdeno y oro como los Chancas, Cotabambas, Las Bambas, etc.

Sep 21, 2013

By Vicente Gonzáles Otoya

El presente texto describe el descubrimiento, cubicación y evaluación del fosfato de Bu -Craa en la provincia de Sahara. Para ello, se realizó campañas donde se hizo el reconocimiento exhaustivo del límite de afloramiento del Paleoceno en toda la provincia, que va desde Hasi Melehes hasta Villa Cisneros, así como se determinó que las capas fosfatadas importantes estaban localizadas en este tramo geológico. Así también se revela la geografía, sondeos, testificaciones, pozos y calicatas y la organización del trabajo de evaluación de dicho sector.

Sep 1, 1971

By Marcus Francisco Gonçalves Mesquita

As mudanças no plano estratégico de uma organização reverberam por todos os seus setores, gerando demandas de alinhamento estratégico. Entre estes setores estão os de planejamento e programação da manutenção. O presente estudo de caso descreve uma iniciativa de alinhamento estratégico realizada pela equipe de planejamento de manutenção da unidade Germano da Samarco Mineração S/A, uma empresa de mineração, localizada no estado de Minas Gerais. A partir de uma revisão na estratégia corporativa foram derivados a missão, visão e valores da equipe. Esses por sua vez, serviram de base para uma revisão dos processos de trabalho e para a definição de ações de melhoria. Por fim foram estabelecidos indicadores para mensurar a realização da visão. Os resultados apresentados por esses indicadores comprovam que as equipes de planejamento podem obter e demonstrar resultados significativos através de técnicas elementares de planejamento estratégico.

Aug 16, 2017

By Marcus Francisco Gonçalves Mesquita

As mudanças no plano estratégico de uma organização reverberam por todos os seus setores, gerando demandas de alinhamento estratégico. Entre estes setores estão os de planejamento e programação da manutenção. O presente estudo de caso descreve uma iniciativa de alinhamento estratégico realizada pela equipe de planejamento de manutenção da unidade Ubu da Samarco Mineração S/A, uma empresa de mineração e pelotização de minério de ferro, localizada no estado do Espírito Santo. A partir de uma revisão na estratégia corporativa foram derivados a missão, visão e valores da equipe. Esses por sua vez, serviram de base para uma revisão dos processos de trabalho e para a definição de ações de melhoria. Por fim foram estabelecidos indicadores para mensurar a realização da visão. Os resultados apresentados por esses indicadores comprovam que as equipes de planejamento podem obter e demonstrar resultados significativos através de técnicas elementares de planejamento estratégico.

Aug 7, 2018

By Walther Rodolfo Ventura Gallardo

El presente texto señala un ejemplo de desembalse de relaves desarrollado en el campamento Comihuasa, perteneciente a la Compañía Minera Cautelosa S.A., donde se afectó las condiciones naturales de los ríos, población y actividades productivas. Por tal motivo, se ejecutó un plan de acción inmediato y de corto plazo que consiste en un estado de alerta de los establecimientos de salud, protección del ganado para evitar que beban agua de los ríos contaminados, inventario de animales afectados por falta de agua segura para su consumo, construcción de abrevaderos, abastecimiento de agua para ganado, recojo de relaves y suelos afectados, su disposición adecuada y segura, rehabilitación de suelos, recuperación de pastizales, repoblamiento de especies acuáticas en los ríos, supervisión del cumplimiento de las medidas de remediación, y recuperación de la calidad ambiental y sanitaria de los ríos.

Jul 1, 2014

By Fábio de Oliveira Braga

Blindagens cerâmicas são frequentemente utilizadas para proteção contra projéteis de alta energia, como os de calibre 7,62 mm e 5,56 mm. Recentemente, foi demonstrado que a modificação da geometria da face de impacto, de plana para convexa, possibilita uma melhor distribuição das tensões geradas pela interação do projétil com o alvo. Este efeito provocaria um aumento na absorção de energia do projétil, proporcionando uma maior segurança ao usuário. No presente trabalho caracterizou-se uma blindagem com a face cerâmica convexa, por meio da metodologia da norma NIJ-0101.06 (2008), ou seja, pelo ensaio balístico com medição do trauma em um material de referência que simula a consistência do corpo humano. Este ensaio visa a aplicação do material em coletes balísticos. Foi observada uma melhora significativa no desempenho balístico após a modificação da geometria.

Oct 30, 2017

By Luís Carlos da Silva

Nos dias contemporâneos, houve uma evolução do armamento utilizado e há uma tentativa dos centros de defesa e balística de acompanhar essa evolução no desenvolvimento de blindagens cada vez mais eficientes. Essa eficiência passa tanto na leveza do material quanto na sua capacidade de proteção. Vivemos também nos dias atuais uma preocupação com questões ambientais e energéticas e é justamente, envolto nesse cenário que pesquisas relacionadas à utilização de fibras naturais (FNL’S), tem se tornado cada vez mais relevantes. Desta forma, o objetivo deste trabalho é avaliar o desempenho individual de compósitos de matriz poliéster reforçados com fibras de sisal, quando submetidos ao impacto balístico de munição com calibre de 7,62 mm. Neste trabalho foram testados compósitos reforçados com 20% e 30% em volume de fibras de sisal. Com um auxílio de um radar Doppler, foram registradas as velocidades inicial (de impacto) e residual (após a perfuração do impacto). De posse desses dados foi possível calcular à energia cinética absorvida pelo compósito e estimar à velocidade limite do projétil que essa blindagem é capaz de suportar. Os resultados após alguns tratamentos estatísticos demonstraram que o compósito em questão tem resultados similares à outras blindagens reforçadas com FNL’S, representando mais uma opção de blindagem moderna.

Oct 30, 2017

By Fabio Tavares Chamonge

A Decapagem 3 da Usina de Cubatão, instalada em 2013, possibilita a oferta de novos produtos ao mercado consumidor e a agregação de especiais valores àqueles já oferecidos pela Usiminas, incluindo a ampliação do portfólio de produtos. Desde a partida, os resultados da Decapagem 3 evoluíram significativamente, com base nos indicadores de segurança, qualidade, produtividade. Obteve-se consistente redução das dispersões de processo o que resultou, entre outros, em produtos com qualidade superficial superior. Para que isto fosse possível, um abrangente conjunto série de ações foi planejado e executado. Este trabalho apresenta os principais resultados obtidos e as ações implantadas no período inicial de funcionamento da Nova Decapagem.

Aug 16, 2017