Search Documents

By T. Liu, C. Shi, T. Fu, M. Zhong

Water inrush in coal mines is induced by the imbalance of the groundwater flow field and the engineering geo-mechanics field. Therefore, to prevent water inrush it is important to predict the critical hydraulic pressure of water inrush in coal seam floors. This paper will investigate a method for conducting theoretical forecasting of the critical hydraulic pressure of water inrush in coal seam floors by adopting the combination method of a genetic algorithm-neural network. First, the topology structure of a neural network (NN) based on genetic algorithms (GA) will be determined and then the critical pressure of water inrush in a coal seam floor using the chosen NN will be predicted. Finally, theoretical forecasting results will be compared with actual measurement results to determine the feasibility and applicability of this method.

Jan 1, 2008

By L. Mpolokeng, J. P. Labuschagne, H. Yilmaz

"An investigation into pillar cutting was carried out at a platinum mine on the western limb of the Bushveld Complex. The focus was on crush pillar design and implementation in order to ultimately improve the compliance percentage for pillar cutting. The major findings from the investigation suggest that the pillar cutting problem lies with the implementation of the design rather than the design itself. Observations of the practical issues underground that prevent good pillar cutting were made. After these issues had been identified, recommendations to rectify these problems and a few other issues identified during the investigation were provided. The recommendations are aimed at improving the pillar cutting compliance and reducing the likelihood of pillar bursts or pillar runs, which will ultimately create a safer mining environment. Paper written on project work carried out in partial fulfilment of BSc. Eng. (Mining Engineering)"

Jan 1, 2015

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980's compared with a typical company's corporate borrowing capacity.

Jan 1, 1984

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By James R. Hein

Manganese nodules from the Cook Islands (CI) Exclusive Economic Zone (EEZ) are compositionally different from other nodule fields. CI nodules have relatively high cobalt concentrations and low nickel, copper, and manganese concentrations (e.g. Hein and Petersen, 2013). This reflects the predominantly hydrogenetic (seawater source) origin for metals in the CI nodules versus dual seawater-pore water sources for most other nodules. The concentrations of many critical and strategic metals have not been previously analyzed for CI nodules, so comparisons with other nodule fields have been limited. To address this, we analyzed a set of nodules distributed throughout the CI EEZ for a complete set of 67 elements, including all of the metals that may be of economic interest, such as the rare earth elements (REEs), yttrium, tellurium, niobium, zirconium, tungsten, titanium, and others (see selected elements in Table 1). In addition, we recalculated the tonnages of nodules and contained metals from nodule abundance areas (in square kilometers) determined by GIS ArcMap calculations based on JICA/MMAJ (2001) nodule distributions. The nodule tonnage calculated and summed from each abundance sector yields a total inferred resource estimate of 9.66 billion tonnes of nodules covering an area of 1.21 million square kilometers; using a cut-off of 6 kilograms of nodules per square meter, yields a median tonnage of 8.59 billion tonnes of nodules covering 687,647 square kilometers (Table 2).

Sep 14, 2011

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By Zohreh Kazemi Motlagh, Virginia T. McLemore

There are more than 15,000 abandoned mine features in New Mexico. A considerable number of these mines have not been cataloged or assessed for prioritized reclamation efforts. These mine wastes can be examined as a resource of critical minerals. Many of legacy mine waste deposits have undiscovered commodities and critical minerals, due to low recovery processes during past production. In this project, Black Hawk mine wastes in Grant County, New Mexico are examined by thorough mineralogical and geochemical characterization. This project seeks to characterize and estimate the critical minerals in mine wastes of Black Hawk mine, and determine the acid generating potential of mine waste. Identifying and producing critical minerals in New Mexico may directly benefit the U.S economy and national security.

Feb 1, 2024

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011

By Reno H. Sales

The syngenetic, metamorphic water, and source bed concept theories of ore deposition proposed by Anton Gray, C, Lo Knight and others, to explain ores in sedimentary rocks, are challenged on the basis of a survey of the literature and personal observation, A hydrothermal origin for the Northern Rhodesian Copperbelt deposits is indicated by the presence of post-Roan age igneous rocks and post-gabbro mineralization, the wide distribution of ore in the various Lower Roan lithologic types, and the zoning of the copper-iron sulphlde minerals and minor elements The proposal by Gray and Knight that igneous rocks are not favorable as guides to nonferrous metal deposits, and Gray&apos;s hypothesis that the redistribution of connate waters and their dissolved metals by metamorphic processes was responsible for the emplacement of ores, are rejected as contrary to field evidence, The absence of exposed potential igneous source rocks is shown to be an invalid argument for the proponents of any syngenetic hypothesis, The common association of ore deposits with calc-alkaline intrusive rocks and their derivatives is, however, demonstrated to be convincing evidence that an exploration program based upon a magmatic theory of origin, would have found most of the important known non-ferrous metal deposits of the world, It is urged that prospecting be continued on the sound basis of accumulated knowledge of the lithologic and structural facts surrounding known ore deposits.

Jan 1, 1960

By M. K. Larson

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment, and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. But this efficiency also comes at a cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impacts of underlying assumptions in each method is essential to proper use of results in mine design. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health

Jan 1, 2009

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

By C Young

In the vast expanse of Western Australia’s mining sector, a critical issue has come to light: many mining operations overlook the power of a Broad-Brush Risk Assessment (BBRA) to uncover their critical risks. This oversight has led to a cascade of challenges, where some mining endeavours find themselves grappling with: - Unidentified and unmanaged fatal risks, casting a shadow of uncertainty and heightened compliance risks. - A bewildering landscape where the concept of critical risks remains enigmatic, with some mistaking the risk register for the BBRA. - A fog of confusion surrounding the guardianship of these critical risks, leaving safety responsibilities blurred and undefined. Yet, the solution lies within our grasp. An effective BBRA empowers organisations to: - Pinpoint with unwavering certainty every ‘true’ critical risk. - Clarify ownership for each critical risk, ensuring accountability and swift action. - Create a prioritised roster of critical risks, illuminating the path to safer operations. - Lay the foundation for essential follow-up actions like bow-tie analysis, the identification of critical controls, and the fortification of the safety and health management system. Join us in this presentation, where we delve into the heart of an industry-leading BBRA process. Discover practical insights that will enable your organisation to craft and implement BBRA strategies, bridging the gaps in your journey toward preventing fatalities and fortifying safety protocols.

Apr 16, 2024

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982