Search Documents

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By Ward G. Wilson

Best practice in the design and construction of soil cover systems for mine waste management has advanced extensively over the past two decades. While significant progress has been achieved, we still have little experience with respect to proven performance for cover systems that must last hundreds of years. Some cover designs appear to be functioning well, while at the same time the performance of many more are now being called into question. This presentation evaluates the integrity of cover systems from both a global and local perspective in relation to the uranium industry within Canada.

Aug 1, 2010

By W. W. Beaton

The Coxheath copper mine is situated on the north side of the Coxheath hills and opposite the French Vale, at a distance of about 10 miles southwest of Sydney, Cape Breton county. The deposit was discovered in 1880, and the first work on the property was carried out with local capital. Lacer some Boston men became interested and formed a Company to finance the undertaking. This group operated the mine intermittently for approximately 20 years, spending close to one million dollars on the undertaking. Three shafts were sunk to depths of 110, 190, and 340 feet, and further underground workings to the extent of approximately one-half mile were driven. Also, an extensive surface programme was carried out. in which many test pits and hundreds of feet of trenches were dug, Early in the summer of 1928 the Arno Mines, Limited, optioned the property and immediately started an exploration campaign. A series of trenches were dug along the parallel vein system, and over 4,000 feet of diamond-drilling was done. The results obtained were so encouraging that a mining plant was erected in the fall of chat year and No. 2 shaft was drained. A complete new plant was installed, consisting of one 120 h.p. Fairbanks-Morse Diesel engine, direct connected to a Sullivan angle compound, air compressor; an 80 h .p. Leonard boiler, which supplies power for the 7 by 11 Ingersoll-Rand hoist; and a Sullivan class C steel sharpener and oil furnace. Two 250-gallon Cameron pumps, one operated by steam and the other by air, were placed in the mine so that, in case of a break-down, the mine would not be flooded.

Jan 1, 1930

By S. S. Jenkins Jr.

While the method is seldom used anymore, coyote blasting is an historically interesting way to blast large quantities of rock. It was used extensively in the days before modern fast drills were available and can be very effective in some formations that have a natural breakage pattern. This paper will cover the general principles, some blast design factors and point out several actual blasts including some very large ones.

Jan 1, 2005

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By R K. W Merkle, S Madoom Hussain, T Yellappa

Cr-Ni-Cu¦PGE deposits are known to occur in early Archaean mafic-ultramafic rocks. Early Archaean mafic-ultramafic (MUMF) rocks occur in the western Dharwar craton and range in size from small pods to schist belts. These MUMF pods consist mainly of meta-peridotites, tremolite-actinolite schists, serpentinites, amphibolites and metabasalts. Spinifex, nodular and ocelli textures are also present. The rocks have been subjected to greenschist and amphibolite facies metamorphism. Geochemical studies were undertaken to evaluate the possible occurrence of economically important elements in the mafic-ultramafic enclaves around the major Arsikere-Tavarkere lineament and surrounding gneissic terrain adjoining local shear zones that occur as discontinuous pods between Arsikere and Chennagiri. Talc-serpentine and tremolite- actinolite schists contain chromite which is rimmed by ferrit-chromite. A notable feature of these MUMF rocks is that they exhibit high MgO (22 - 40 per cent), total iron (8.34 - 10.01 per cent), Ni and Cr (~3000, 2800 ppm) contents, with some samples showing komatiitic affinity. The rare earth elements (REE) data show slightly fractionated patterns with enriched LREE (LREE/HREE ~5.0) and negative europium anomalies. The Pt and Pd values reach 6500 and 191 ppb. The MUMF rocks, especially those exhibiting high chromium contents and occurring near shear zones, are potential hosts for economic platinum group element (PGE) deposits.

Jan 1, 2008

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011