Search Documents

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By José Francisco Cabello Russo, Denilson Rodrigues de Araújo, Elias Fonseca de Castro, Henrique Dias Gatti Turrer

The Minas-Rio project of the Anglo American group was designed to produce pellet feed from a low-grade itabirite. The comminution circuit has three HPGR’s and two ball mills. This type of circuit, with HPGR (open circuit) followed by ball milling (closed circuit), is called a hybrid circuit. The literature shows this hybrid circuit as being more energy efficient. The main objective of this work was to evaluate the benefits of using the HPGR in the energy consumption of the grinding and regrinding and the secondary objective was to show the impact of the press on mass recovery of desliming and flotation, in view of a possible higher generation resulting from the pressing of the material. The results obtained in this work showed that the HPGR reduced the specific energy consumption in the comminution stages existing downstream of the press, increased the recovery of the flotation and did not decrease the recovery of the desliming stage.

Oct 3, 2019

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By Yi-Chun Lin

Mechanical/Electrical/Piping (MEP) systems, due to their complexity and diversity, are the most intricate part of building construction. This being the case, Combined Services Drawings (CSD) and Structure, Electric and Mechanic(SEM) drawings can ensure that all coordination issues are resolved prior to construction. Construction companies attempt to apply Building Information Modeling (BIM) to manage and integrate engineering information and solutions efficiently into the CSD and SEM processes to enhance the accuracy of design and the efficiency of review. There are several powerful commercial tools, such as Bentley Navigator, Autodesk Navisworks, and Tekla BIMsight, that can review the integrated BIM model and detect conflicts in systems, and allow planners to correct the conflict issues one at a time. However, for increasing numbers of conflicts, this may be inefficient, and requires them to be arranged in a list according to impact and seriousness before solving them. For this reason, this research implements a module for conflict impact assessment based on rule-based reasoning to classify and weigh conflict impact and seriousness, and highlight the conflicted objects in the BIM system in different colors depending on their conflict type and seriousness during the analysis. This system not only detects and lists possible conflicts and errors, but also sorts them according to the severity of impact and conflict type. Planners can effectively modify the BIM models according to these conflicts as they are listed and visualized in the BIM system. If these conflicts, such as pipeline interference and problems of insufficient space, can be avoided in the early stages of planning, it facilitates the achievement of project objectives in quality, scheduling, and cost.

Aug 1, 2013

Environmental conflict management approaches and procedures have been used to successfully address and resolve a variety of issues, problems, and conflicts related to the extraction of natural resources. Companies in the mining industry have been involved in a range of controversies over planning, siting, permitting, environmental, and enforcement issues. Through the use of conflict resolution case studies, this paper will present approaches and procedures that can help companies and other involved parties to successfully manage and resolve differences in a mutually acceptable manner.

Jan 1, 2000

What is a conflict, as it is understood by men of the extractive industries? And what are the circumstances out of which these conflicts arise? A start can be made with the notion of economic conflict, which can be defined as rivalry over the use of economic resources. Such rivalry is a central part of all economizing activity. It is present within the individual, within the family, and within the business firm. In each of these units there are multiple goals competing for use of a limited income. And economic rivalry is present among individuals and firms who are competing with one another for use of the limited quantity of economic resources available to us as a society.

Jan 7, 1961

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

By Rafael Humberto Mota de Siqueira

A conformação a laser (Laser Beam Forming – LBF) é um processo mecânico sem contato realizado pela introdução de tensões térmicas na superfície de um material com laser, a fim de induzir a deformação plástica. Neste estudo, foram realizadas conformações em chapas de 1,6 mm de espessura, de alumínio de alta resistência, classe AA6013-T4, com uso de um laser de Yb-fibra operando em modo contínuo. A potência do laser foi variada entre 200 e 1000 W e a velocidade entre 3 e 30 mm/s, com o feixe desfocalizado em 5 mm sobre a superfície da chapa. O ângulo de dobramento das chapas variou entre 0,1 e 2,5° por passe, dependendo das condições experimentais. Na condição de maior ângulo, 1000 W e 30 mm/s, a poça de fusão atingiu 0,6 mm de profundidade, porém sem alterar a microestrutura da parte inferior da chapa. Em todas as condições, a dureza se manteve constante em aproximadamente 100 HV, sendo semelhante ao material de base. Para verificar a aplicabilidade do método, foram desempenadas chapas previamente soldadas na configuração T. O método mostrou-se eficiente em corrigir o empenamento de chapas com inclinação de até 5°.

Aug 16, 2017

By George A. Lawrence

A new super-large 100 m3 (3500 A3) pneumatic mechanical flotation cell is now available to meet future mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom cylindrical tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. This new flotation cell is powered by a custom designed hydraulic motor package that provides infinite speed control in individual cells and a soft start under load

Jan 1, 1993

By T. Orser

In 2010 Newmont made the decision to purchase a 42 foot (ft) Semi-Autogenous Grinding (SAG) mill from Metso and a 28 Mega-Watt (MW) Gearless Mill Drive (GMD) from ABB for the Conga Project in Peru. The test and study work showed that a single line 42 ft SAG mill circuit gave the most favorable project economics in comparison to an equivalently powered single line 40 ft SAG mill circuit. This paper does not address the process design or the project economics, but instead focuses on the key aspects of the SAG mill design, GMD design and the associated component manufacturing. This paper also addresses, where applicable, the potential reliability differences between the initially proposed 40 ft SAG mill and the finally accepted 42 ft SAG mill.

Jan 1, 2012

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By O. F. Carter

"Coniaurum Mines, Limited, hold nineteen claims in Tisdale township, in the Porcupine district, adjoining the McIntyre mine on the east. They extend for over a mile along the strike of the Hollinger-McIntyre 'break'. The property has been explored extensively along the ore zone both laterally and vertically. Workings have been carried to a depth of 5,500 feet, and nearly 50 miles of lateral workings (drifting and cross-cutting) have been driven to date in development and in gaining access to the orebodies.Production started at the Coniaurum in June 1928 and has continued without interruption. To the end of 1946 the plant has treated 2,695,725 tons of ore, yielding gold having a value of $21,989,918.The Coniaurum is controlled by Ventures Limited of Toronto. Mr. John Redington, who has guided all operations since work began on the property in 1922, is Managing Director.GENERAL GEOLOGYAge and Types of RocksKeweenawan- Quartz diabase dykes.Algoman - Quartz porphyry intrusive; the veins are probably late Algoman.Keewatin - Lava flows.Brief Description of Rock Types.Diabase DykesTwo quartz diabase dykes traverse the property in a north-south direction, cutting all formations, including veins.Porphyry IntrusivePetrographically all porphyries in the Coniaurum are of the usual Porcupine type- quartz-feldspar with alteration advanced in most instances to the stage where the feldspars are completely dissolved, leaving a wellsheared carbonate and sericite matrix with embedded rounded quartz 'eyes'. Alteration is most extensive in the smaller bodies and in the narrow protuberances from the larger masses; the cores of the larger masses are generally much fresher, with more or less well defined feldspar phenocrysts."

Jan 1, 1954

By L. Stas

The authors have been interested in stress measurements in the rock mass for a long time. This paper describes the development of new apparatus for stress measurements in a rock mass. The principle of stress measurement by this device is based on the relief method as applied on the conical shaped surface of the bottom of a borehole. The design started based on the experience of K. Sugawara and Y. Obara who have been using the compact conical borehole over-coring system (CCBO). The conical shape of the strain gauge probe CCBO makes the fixation of the probe in borehole easy and, also, makes the measurement of stress in independent directions possible. The principle of the measuring method, the preparation of the borehole, the design of the probe for continuous measurement of stress during the course of overcoring are described. Also, a simplified version of the probe for long term monitoring of stress variations in the rock mass by means of the inserted body method and the initial laboratory results and in-situ testing of the development sample are described. Additionally, testing was done regarding the possible glues in relationship to the creep effect for this case.

Jan 1, 2006

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By Bruno Lafrance

Abstract - Quartz veins at the Mufferaw gold prospect and Komis gold deposit, northern Saskatchewan, are examples of oblique-extension veins that crystallized in shear and tensile fractures, which propagated and then opened oblique to their walls during a single continuous deformation event. The Mufferaw gold prospect consists of an interlinked mesh of conjugate shear fractures, tensile fractures, and veins. Oblique-extension veins crystallized in conjugate shear fractures, which opened during dilation of intersecting tensile fractures under the same far-field stress system. At the Komis gold mine, tensile and dextral shear fractures cut across granodiorite dikes. The tensile fractures formed perpendicular to the dike margins during stress transfer from the less-competent country rocks to the more-competent dikes. During extension of the dikes oblique to the bulk extension direction in the country rocks, the tensile fractures were reactivated as sinistral shear fractures. The reactivated tensile fractures and dextral shear fractures opened oblique to their walls, parallel to the bulk extension direction, and were sealed by the deposition of oblique-extension veins during the same deformation event.

Jan 1, 2004

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990