Search Documents

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

By Robert C. Munro, Kenneth M. Reim

NEW IDRIA INTRUSIVE For the most part this ultrabasic mass is a highly sheared serpentine, the exposed rock being made up of small serpentine chips and plates, the faces of which have been slickensided. Throughout this sheared material there are residual blocks of serpentine and highly to moderately serpentinized peridotite. The faces of these resistant blocks show rounding and slickensiding and their size varies from pebble size to diameters of over 5 ft. Certain areas have seemingly resisted the shearing stresses and remain as moderately fractured serpentine. Throughout the ultrabasic mass are bodies of silica-carbonate rock, silicified serpentine and minor concentrations of magnesite and chromite.

Jan 9, 1962

By S Raval

The estimation of greenhouse gas emissions from coalmines is increasingly becoming a priority for both operators and regulators. At the same time, involved scientific challenges in the methane measurements is generating significant interest from global research community. Various technology providers are also actively engaged in improving their sensors and platforms to address the measurement challenges and capitalise the market opportunities. This presentation highlights rapidly evolving multifaceted landscape of coalmine greenhouse gas emissions. It covers the advances in sensors for the detections, including ground-based, airborne, and satellite-based systems as well as models for the emission estimations, including attempts to reduce the involved uncertainties.

Sep 1, 2024

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

By Georg Unland, Thomas Wegner

"Different types of impact crushers use the physical effect of impact to crush rocks. The rocks can vary from soft to hard and from ductile to brittle but they should never be abrasive. Since the principles of impact crushing of larger rocks are hardly investigated these crushers are still sized rather by empirical than by scientific approaches.In order to investigate the principles of comminution by impact of large rocks a test rotor was developed and rocks of different dimensions were tested. The integrated measuring devices of the rotor enable the recording of impact forces and of absorbed impact energy with high resolution during the contact time.Since impact crushers stress the rock particles with a defined velocity the main crushing properties are gained as a function of the applied velocity and the particle size of the rock: likelihood of breakage, contact time, maximum crushing force, mass specific crushing work, surface related crushing ratio and crushed fragment shape distribution."

Jan 1, 2003

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984