Search Documents

By Karl E. Burger

Recently an experiment was completed at the Golden Sunlight Mine, a property owned by Placer Dome Inc. of Vancouver, British Columbia, to measure the Body Waves entering their highwall created by blasting. The purpose of the study was to assess the damaging effects of blasting on the highwall, in order to further slope stability. Stress and Strain experienced in the earth that is created as a result of blasting can be determined by knowing several important pieces of information. These include the compressional and shear wave particle velocities initiated by blasting, the Body Wave travel velocities in both the shear and longitudinal direction, and the densities of the rock in question. A series of equations based on wave theory can then be used to determine the stress and strain affecting the highwalls. The Blasting Engineer can then use this information to design blasts that create peak particle velocities less than levels that maintain the integrity of the highwalls. This paper first discusses the experiment used to measure the Body Wave velocities. It then traces through the subsequent calculations necessary to generate the information needed by the Blasting Engineers, the Mining Engineers, the Geological Engineers, and the Geophysicists to design blasts and develop open pit plans to alleviate unstable highwall conditions.

Jan 1, 1989

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996

By Rick Coleman, Chelvan (Chevy) Veloo

"P.T. Freeport Indonesia's lrian Jaya Operation has been producing copper concentrate continuously since 1972. Numerous ore discoveries and five mill expansion programs have seen the initial milling rate of 7,200 MTPD escalate to the present rate of 125,000 MTPD, producing 2.5 million pounds of copper and 3,500 troy ounces of gold per day. The latest expansion, commissioned in February 1995, incorporates a 34 foot Semi- Autogenous Grinding (SAG) Mill, two 20'x30' Ball Mills, conventional roughing, cleaner column flotation, and attendant upgrades to the existing concentrate pumping and dewatering facilities. This paper will describe the SAG Plant flowsheet, and focus on the key training issues which contributed to a successful plant start-up.IntroductionP.T. Freeport Indonesia's operations in the Ertsberg mining district are located in the Jayawijaya Mountains of Irian Jaya, the easternmost province of the Republic of Indonesia. P.T. Freeport Indonesia (PTFI), the operator, is owned by Freeport MacMoRan Copper and Gold (81.3%), the Government of Indonesia (9.4%), and private Indonesian investors (9.4%). Geographical location, and sailing distances are provided on the attached location map.The operation stretches over 7 4 miles ( 114 km) from the dewatering and concentrate shipping facility at the Port of Amamapare on the Arafura Sea to the Grasberg open pit located at 3400m. The regional geology is covered in detail by Van Nort et al (1991 ), with current proven and probable reserves estimated at 1.13 billion metric tonnes grading 1.30% Copper, 1.42 ppm Gold, and 4.06 ppm Silver. The Grasberg open pit mining operation provides 92% of the mill feed, and is described in detail by Hickson (1991). The remainder of the mill feed is derived from several underground block caving operations. Current production rates provide a mine life in excess of 25 years. However, very favorable geology in the area leads to expectations that additional reserves will extend the life of the operation considerably."

Jan 1, 1996

By L. Hacini

The start-up is the most critical phase of the cell life, as an uncontrolled start-up could lead to early infiltrations, instabilities, and in some cases to the cell death. Lots of efforts are put to increase the lifespan of cells, as it has a major impact on both the operating costs and the environmental footprint of the aluminum industry. Obviously, a true size test on a cell is a resources- and time-consuming approach that could be used only to validate mature concepts. Moreover, numerical modelling is a low-cost and versatile tool capable to test a wide range of potential ideas and concepts. In the present article, a thermal electrical mechanical slice model is presented. This model describes the preheating and bath periods of a P155 aluminum cell start-up, as used at the Grande Baie smelter. The impact of sodium diffusion and expansion is also included in the model. This model will be useful to study different problematical issues such as the global behaviour of lining materials, shell and cradle deformations during start-up and several start-up scenarios. Such a model will also be able to answer some interrogations regarding early infiltrations and their impact on the lifespan of the electrolysis cell.

Jan 1, 2011

By Jerry Luttman, Mark Dubay, Anvesha Dogra, Elizabeth Dwyre, Wei Hu

The I-75 Modernization Project (Segment 3) just north of Detroit, MI is being delivered as a Design-Build-Finance-Maintain (DBFM), which is a Public Private Partnership (P3). The project includes design and reconstruction of 5.5 miles of freeway, including a depressed section with a 20,630-ft long, 14.5-ft inside diameter, up to 100-ft deep stormwater tunnel, multiple drop shafts, and a pump station. The project also includes a maintenance term of 25-years. This is the first time MDOT has used a P3 delivery method for a major highway and tunnel project. This paper describes the development of the P3 documents, including performance-based tunnel and shaft technical requirements, and the approach to project risk management, financing, and insurance coverage.

Jun 23, 2024

By A M. Mueller

St Helena tunnel is the centrepiece of the Pacific Highway upgrade from Tintenbar to Ewingsdale, abbreviated and commonly known as T2E. At the deepest point the twin tunnels run 45 m below the ridge line of St Helena Hill, located about 5 km west of Byron Bay. The tunnel breakthrough was achieved early in 2014 and the works for permanent lining will be completed in early 2015.Once the project will be handed over to the public in 2015, T2E will deliver a safer highway and uninterrupted traffic flow between New South Wales and Queensland. The design speed in the project area has been set to 110 km/h by the client Roads and Maritime Services (RMS), which will reduce the travel times between Brisbane and Ballina to just over two hours.The two tubes of the tunnel have been designed to accommodate three lanes in each direction with shoulders and walkways on either side of the carriageway. These requirements result in a huge cross-section of about 20 m width and an excavated area of about 210 m2.With the tunnel alignment being situated in basaltic rock, St Helena tunnel is conventionally driven. The selected excavation method was predominantly drill-and-blast with temporary support being installed immediately after the excavation. Despite the wide span of the tunnel, the geology allowed the tunnel perimeter to be supported by only rock bolts and a layer of shotcrete over the majority of its length.Due to environmental reasons one of the approval criteria of the project was that the tunnel must not have a detrimental long-term impact on the groundwater system within St Helena Hill. Consequently the tunnel has been designed as a fully tanked structure with a waterproofing sheet membrane installed on the temporary shotcrete.The permanent structure of the tunnel has to meet a 100-year design life and it is designed as a cast in situ concrete lining. Considering the water pressure on the lining the concrete is reinforced with a significant amount of bar reinforcement.The presented paper provides a more detailed explanation of the geology and the consequential temporary and permanent support measures together with the waterproofing system.CITATION:Mueller, A M, 2014. Pacific Highway upgrade from Tintenbar to Ewingsdale (T2E), St Helena Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 419–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

The eastern third of Australia contains an unrivalled Phanerozoic rock record generated by the regional interaction of Gondwanaland with the Pacific and by the global effect of the 400 m.y. Pangaea - Panthalassa cycle. Between the latest Proterozoic (600 Ma) breakup of Proto-Pangaea and the mid-Carboniferous coalescence of the dispersed continents in Pangaea, the Lachlan and Thomson Foldbelts accreted to the craton by Mariana-type (backarc basin) and Chilean-type (continental margin) subduction from eastward jumps of the Palaeo- Pacific rim. Further jumps of the rim of the Permian and Mesozoic Pacific, now expanded to Panthalassa, accreted the New England Foldbelt to the craton. An Early Permian rift basin was succeeded by a Late Permian to mid-Triassic foreland basin which extended between the craton and the foldbelt behind the 10000 km Panthalassan rim, from the Bowen Basin of Queensland to South America, and was host to the productive coal measures of eastern Australia, as the succeeding Jurassic and Early Cretaceous foreland and epicratonic basins included the coal measures, hydrocarbon reservoirs, and aquifers of the Great Artesian Basin. The magmatic arc on the Australian margin ended after the mid-Cretaceous uplift along the Queensland coast that initiated southwestward drainage from the high Pacific rim. The Chilean-type subduction that had prevailed since the Devonian was superseded shortly afterwards by Mariana-type subduction with the successive generation of the back-arc basins of the Tasman Sea, Coral Sea, and other southwest Pacific basins by the migration of the island arc to its present position 2500 km eastward of Australia.

Jan 1, 1990

By James R. Strong

Before getting into the subject of packaging and materials management, please permit me to introduce you to MICRO SWITCH. MICRO SWITCH, A Division of Honeywell Inc. is located in Freeport, Illinois. We manufacture and market thousands of types of precision snap-action electrical switches. Most of them are used as components by other manufacturers in industrial and commercial products. MICRO SWITCH also offers a broad line of industrial control devices including heavy- duty limit switches, relays, manual controls and proximity switches. Other product lines are solid state keyboards for the computer industry and high-performance d.c. motors used in computer related equipment. So you can see that we are a component manufacturer. With the exception of the keyboards, every one of our products would "fit comfortably into a breadbox." Some are so tiny that one could easily fit several thousand into a man's hat. In my position as supervisor-packaging. package design, and materials handling engineering, I am actively involved in package design projects, parts handling design projects, and numerous activities involving departmental layouts, storage facilities, and material handling equipment. Two package design technicians, a materials handling engineer, and a materials handling technician make up the technical staff.

Jan 1, 1973

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By Alessandro Martinis

The performance requirements for modern steelmaking facilities are ever more stringent, as customers and markets are continuously pushing for technologies which allow having high quality steel produced in an economic and sustainable way. In the details, this paper has the aim to present the excellent results obtained by integrated steel plant where an EAF is fed with high quality hot ENERGIRON DRI. The recent technology developments, combined with the affirmed basic process design, contributed to further maximize the energy of the DRI, reaching the EAF at temperatures above 600°C with a carbon content up to 3.5%, as confirmed by plant data. These improved input material characteristics resulted in reduced electrical energy consumption and increased liquid steel production.

Aug 16, 2017

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987