Search Documents

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable capacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine owners and environmentalists alike.

Jan 1, 1976

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the high funding level program plan.

Jan 1, 1980

By Robert A. Cummings

A rock mass classification system has been developed for recommending drift support requirements in block caving mines. This development follows a two-year program incorporating field observations of support practice and performance in rocks of different classes, at several U. S. block caving mines. Popular rock mass classification systems presently in use for tunneling were applied at the various field sites; and were evaluated for conformance with caving mine support requirements and for general utility to caving mine operations. The developed system (MBR System) accepts readily-obtainable engineering and geologic data to yield a rational estimate of support requirements. The background and development of the MBR system is described in this report (Volume I). The use of the system is given in the Manual, a separate volume (Volume II).

Jan 1, 1984

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the mid funding level program plan.

Jan 1, 1980

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the low funding level program plan.

Jan 1, 1980

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. face drill. The instructions are based upon an actual installation made in the mine on face drill model 460-S. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other face drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other face drills and can determine any necessary modifications if they are not.

Jan 1, 1973

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

Through a contract, the Bureau of Mines has funded the development of an Automated Breathing Metabolic Simulator (ABMS). The ABMS simulates man in all of the breathing and metabolic parameters for monitoring support and resuscitation equipment. For the first time, complete breathing and metabolic simulation are incorporated in the same device. Breathing rate, breathing depth, breath velocity contour, oxygen uptake, and carbon dioxide release are all variable over wide ranges, simulating conditions from sleep to hard work with respiratory exchange ratios covering the range of hypoventilation to hyperventilation. In addition, all of these parameters are remotely controlled to facilitate the use of the device in hostile test environments. The exhaled breath is also at body temperature and completely saturated. The simulation in faith¬ful to the extent of having a variable functional residual capacity and an anatomical dead space equivalent to that of humans. The ABMS will be used as a stand-in for humans in test and validation of respiratory equipment, permitting more extensive and safer evaluation in hazardous environments where human testing would have to be limited. In addition, it will greatly reduce the cost of prolonged testing in cases where simulation chambers with human subjects require three shifts of crews, including standby physicians. Perhaps most importantly, it will provide a calculated and reproducible test and validation facility. The ABMS is under complete computer control. Through a typewriter terminal the test sequence can be input into the computer which will then automatically adjust the ABMS to simulate any desired sequence of metabolic activities for time durations up to 15 hours. The computer also monitors the test procedures and provides test results printout.

Jan 1, 1973

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

Four taconite plants were studied to establish the extent of hazard to plant personnel which exists based on long-term exposure to noise. The criteria for evaluation include the 90 dBA and 85 dBA summations of partial exposures. Data from extensive interviews were used to determine all work stations or locations which employees occupied and how much time they spent in ach location in a typical working day. Noise level measurements at every designated location were then made. By means of a computer program, these time and noise level data were us d to find the optimum noise reductions which would be required throughout each plant to meet both noise criteria. Subsequently, each plant was examined in detail so that the apparent sources of noise for each of the locations requiring noise reduction could be delineated. In tabular form, this report presents the hazardous locations for each plant, the existing noise level, the optimum noise reduction which would be required to meet the current and proposed laws, and the sources of noise which produce the existing noise level.

Jan 1, 1977

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982