Search Documents

The copper and zinc contents of herbarium specimens of 11 of the 12 Australian species of Polycarpaea were determined in order to establish background and anomalous values of potential use in biogeochemical prospecting.Cumulative frequency curves were used to establish appropriate threshold concentrations for six species including the "copper plant"' P spirostylis. Collection localities of Polycarpaea specimens with anomalous copper or copper-and-zinc values are under investigation.

Jan 1, 1978

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By P. V. Avotins, I. Djurkovic, D. R. Nagaraj, M. Grunjic, A. Day

"As part of a major reconstruction and expansion of the Majdanpek Copper Mine, an investigation and optimization of the flotation collector regime was undertaken. The flotation response of the major minerals to various reagents and the effect of pulp chemistry was studied from both a fundamental and practical point of view. These studies led to plant trials and the eventual adoption of a modified collector suite which improved both copper and gold recoveries.INTRODUCTIONThe Majdanpek Copper Mine processes 40,000 tons per day of ore containing about 0.43% cu. In addition to copper, the ore also contains recoverable quantities of molybdenite and gold. The mine has been in operation since 1961 and is the largest in Yugoslavia. It is currently undergoing major reconstruction and expansion. The flowsheet of the Majdanpek concentrator is shown on Figure 1.The ore body is variable in composition and changes in mill feed require proper control of operating variables to achieve the optimum metallurgical results. A detailed study including grindability, flotation response, and solid-liquid separation was carried out on several samples of the ore. Flotation response and the choice of reagent chemistry were found to be very important in achieving the highest recoveries of metal values. An automatic reagent control scheme insured that optimum dosages were used in the plant.The flotation collectors used at the present time include sodium isopropyl xanthate (SIPX), AERO 3302 Promoter and AERO 5415 Promoter. The addition of AERO 5415 to the reagent suite is a recent development and was based on the favorable results obtained in the extensive laboratory testing program conducted to establish the optimum reagent combination and dosages. Subsequent plant tests confirmed that AERO 5415 provided significant improvements in copper and gold recoveries. A description of the mineralogy of the Majdanpek ore and details of laboratory and plant metallurgical data are given in this paper. The chemistry of AERO 5415 Promoter and its interaction with minerals relevant to Majdanpek ore are also discussed."

Jan 1, 1992

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

An Evaluation of Froth Recovery Measurement Techniques

Sep 13, 2010

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By Dr. Anthony J. Konya

The modern era has seen a boom in virtual training platforms. This study details the effectiveness & applicability of online training in comparison to in-person training for the drill & blast industry.

Feb 1, 2020

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

The Crown Minerals Act provides a new+framework for the management of Crown owned minerals and requires that regard be had for the principles of the Treaty of Waitangi. The Act requires the preparation of Minerals Programmes to achieve the Act's objectives of efficient allocation of rights and the recovery of a fair financial return on its minerals. Efficient allocation requires that a permit is allocated to the party which values it most highly. A fair financial return to the Crown must be considered in the context of the economic rent available from individual mineral projects, with the proviso that a nil return to the Crown as the owner of the resource will not be considered a fair return from the community's perspective.

Jan 1, 1992

By Yoginder P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15 percent to a maximum depth of 150 feet. The pit orientations along the dip (dipline), strike (strikeline) and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas, and also to furnish a data base-for the computer simulation models. A dragline micro- simulation model (Fluor), a shovel/truck simulation model and a cost analysis model were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and angle of dip. The productivity (Cu.yds/hour) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity larger size trucks were preferable to smaller size trucks in the pit configuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip.

Jan 1, 1984

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006