Search Documents

By Alisson Paulo de Oliveira, Altair Lucio de Souza, Jacson Morais Borges, Cleiton Arlindo Martins

A customized version of the Microsim-PM software for one Steckel rolling mill was built and adapted for specific mill parameters. The focus of this study is to use this model, which predicts the austenite grain size distribution evolution during rolling, to understand and quantify metallurgical issues happening during hot rolling. This will allow the steel mill to optimize the rolling process and chemical composition before the first industrial trial. Materials rolled for final thicknesses of 4.75, 6.30 and 12.5 mm of a carbon manganese steel and a microalloyed steel were selected to tailor the equations used by the model and to accurately reproduce the reality of the Steckel mill. This paper analyses the results from the customized model and compares them to mill data and final microstructure. Measured and predicted Mean Flow Stress (MFS) values are compared. After rolling, the material is subjected to accelerated cooling using laminar cooling. These cooling curves obtained from mill data are also considered to analyze the final microstructure characterized for all the cases using EBSD. The quantification of the microstructure allows for a better understanding of the relationship between chemical composition, process parameters and mechanical properties.

Oct 1, 2019

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By Henry Rawdon

ONE of the most vital problems in the manufacture of steel at present is the occurrence of the defects that have been popularly termed "snow flakes," "flakes," or "scabs." Particularly is this the problem of many manufacturers who during the past 2 yr. have undertaken large-scale production for the first time. A study of the microstructure of such defective material throws considerable light upon the nature of these defects and is essential before measures may be taken for the elimination of the defects. Flakes do not appear to be found in the plain carbon steels; they have been found, however, in abundance in some of the simple alloy steels that are being used in such vast quantities; viz., nickel steel of the approximate composition, 0.40 carbon and 3.5 per cent. nickel, and in the chrome-nickel type. The present article summarizes the characteristic features of defective steel of the flaky type as they have been found by laboratory study of numerous specimens, and it aims to show the conditions within the metal that are favorable to the occurrence of this type of defect without entering into the details of mill practice (size of ingot, design of molds, rate of cooling, distribution of cooling stresses, etc.), all of which conditions appear to play a role in the production of these defects.

Jan 2, 1919

By S. L. I. Chan, M. Z. Quadir, D. C. Austin, P. J. Hazell, A. Chen, A. A. H. Ameri, D. East, J. P. Escobedo, M. A. Bevan, A. D. Brown

The microstructure and mechanical response of additive manufactured Ti64 under compression and tension has been investigated. Quasi-static and dynamic experiments were conducted on electron beam powder bed Arcam A1 (EBM) and blown powder laser Optomec LENS MR-7 (LMD) additive manufactured specimens. Hot isostatic pressing (HIP) was conducted on both of the additive manufactured specimens and results were compared with as-received specimens. Digital image correlation (DIC) was utilized to observe the in situ development of deformation fields during tensile loading. Optical microscopy was conducted on pristine and deformed specimens to examine the microstructure of the specimens. HIP treatment reduced the porosity by *90% with a concomitant increase in hardness by 40%. The results from tensile experiments show that additive manufactured Ti64 display a higher values for the yield stress, hardness, and ultimate tensile strength than conventionally manufactured Ti64. Under quasi-static compression, it was observed that EBM specimens exhibit a higher yield strength and ultimate tensile strength than LMD specimens.

Mar 1, 2017

By A. R. Farkoosh, J-P. Fortin, M. Pekguleryuz, S. Bagherpour

"Titanium aluminides are structural intermetallics which offer an attractive combination of high temperature strength and light weight. For such properties, these intermetallic alloys have become front-runners in replacing nickel-based superalloys used for several high temperature applications. These alloys are produced from metallic titanium, aluminum and master alloys involving an expensive and difficult process. A low cost alternative to current industrial production method is the new modified aluminothermic process which directly reduces titanium oxide (TiO2) to titanium aluminides. Nevertheless, this process has itself significant challenges in achieving alloys free of oxide inclusions; the close densities of the slag and the titanium aluminides makes slag/molten metal separation a challenging task. Usually, the alloy produced requires a second refining step. In this study, thermodynamic calculations based on CALPHAD method were performed to determine the solidification path and an attempt has been made to develop a criterion to increase the density deference between the slag and the alloy by alloying with appropriate elements. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were utilized to examine the microstructure and phase selection of three Ti-Al alloys produced by the aluminothermic reaction, including the as-cast, refined in a controlled atmosphere and inert-gas-refined alloys. The composition range of the alloys studied was restricted to the a2-Ti3Al + ?-TiAl phase field (Ti-30Al) in the binary Ti-Al phase diagram leading to a lamellar structure with different complex intermetallics as shown in Figure 1.INTRODUCTIONTiAl based alloys are promising structural materials for high temperature aerospace and automotive applications. This is due to some attractive properties such as low density, high specific strength, high specific stiffness and high temperature strength retention (Wen-bin, Xue-wen, Hong-fei, & Yong-feng, 2011). These alloys have become leading candidates to replace Ni-based super alloys in gas turbine engines. Replacement of Ni-based super alloy parts with titanium aluminides is expected to reduce the structural weight of high performance gas turbine engines by as much as 20–30% (Kothari, Radhakrishnan, Sudarshan, & Wereley, 2012)."

Jan 1, 2016

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015