Search Documents

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By W J. Rankin, D R. Swinbourne

There are large tonnages of low-grade manganese ores in India fromwhich it is uneconomic to produce ferroalloys by conventionalsubmerged arc furnace smelting. A possible way to utilise these ores is to smelt them with carbon to produce pig iron and a manganese-rich slag, then to metallothermically reduce the molten slag to silicomanganese. Thermodynamic modelling of the metallothermic reduction stage using aluminium, silicon or aluminium-silicon alloy as the reductant at 1450¦C showed that an acceptable grade of silicomanganese could be produced. Manganese recoveries were predicted to be about 80 per cent. Heat balances indicated that silicothermic reduction may not produce enough heat to maintain reaction temperature. Small-scale laboratory experiments showed that the manganese grade of the alloys, and the manganese recoveries, were close to those predicted, but those for silicon were muchlower. Aluminothermic reduction produced the highest grade manganesealloy. The slag-metal equilibrium involving manganese, silicon and their oxides was investigated and it was found that equilibrium was not attained in any of the experiments, due probably to the very low rate of reactions involving silicon. This could be used to advantage in practice to achieve higher manganese levels in the alloys.

Jan 1, 1998

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By W. M. Jansen

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the 'AMIRA P754-Metal Accounting and Reconciliation' project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called `the propagation of error'.

Jan 1, 2007

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

This paper aims to collate the metallurgical test work undertaken on the Barrytown mineral sands deposit. It is intended to serve as a summary of mineral dressing work undertaken by all interested parties up to the time of writing. Areas requiring further investigation are: in situ grades and recoveries of accessory minerals,the question of 'rank' of ilmenite within the deposit,flow sheet development for the recovery of gold and monazite, andcost analysis to investigate the relative worth of other minerals; notably rutile. Flow sheet development with respect to the Accessory Minerals cannot be accurately defined until the importance of each mineral in terms of grade, recovery and expected revenue is determined. To date, ilmenite and zircon flows are well documented. Further work is needed to quantify recovery's and flows of the other minerals; notably monazite, gold and rutile.

Jan 1, 1989

By L. Joncourt, N. Touchard, G. Pochart, C. Perdon

Worldwide, the major Manganese ores can be separated into three different types: ?Oxidized ores (MnO2): in Australia, Gabon, Brazil,?. ?Semi-oxidized ores (Mn2O3): in South-Africa, Australia,?. ?Carbonated ore (MnCO3): in Ghana, South Africa, Kazhakstan?. The other Manganese ores are less rich but can be used locally or in the neighbour countries (China, Ukraina, India?). Since the beginning of the 20th Century, Manganese has played a big role in the steel industry process average usage ratio: 9,5 kg/mt of steel). The recent grow-up of this industry has led to an increase of Manganese ores demand. In parallel, several companies have increased their Manganese ore producing capacity. In this presentation, we explain the link between the main Manganese ores characteristics and the key different factors for an effective and low cost Mn alloys production (HCFeMn and SiMn): ?Chemistry ?Size ?Reactivity Then we will point out the advantages of Comilog ore and Sintec ® usages in various Manganese alloy metallurgical process compared with the other main ores and with the local ores. Some advised formulations for the different kinds of furnaces and alloys will be also discussed.

Jan 1, 2007

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

High pressure roll grinding (HPGR) is a mature but still expanding comminution technology. In the metals mining industry, HPGR is slowly gaining acceptance as a cost-efficient, high-throughput alternative for plant optimization. The increasing need to treat ores with progressively lower grades, complex mineralogies, refractory metal occurrence and variable rock types requires an energy-efficient comminution technology that reduces metallurgical problems inherent in conventional crushing and grinding, while stabilizing leach and flotation circuits and increasing metals extraction. This paper will summarize our latest HPGR pilot test results for gold and copper projects in the United States and South America and their confirmation through the first HPGR operation in copper mining. This paper will also stress the use of the high pressure grinding roll as a metallurgical tool. The application of HPGR for the treatment of heap leach SX-EW ores, semi-refractory gold ores, waste rock material and concentrator feeds will be illustrated.

Jan 1, 1998

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

By J. Alexis, G. Ye, E. Burström

Over the past twenty years the 3 MW DC arc furnace at MEFOS has been frequently used for development of new processes. These processes include recovery of valuable metals from slag, sludge and dust from steel and other metallurgical industry, treatment of ashes from power plant and incinerators, smelting reduction of minerals and zinc recovery from EAF dust. The process characteristics of the DC arc furnace operation in terms of: ? selective reduction, ? total reduction, ? process stability and flexibility, ? dust carry-over, ? thermodynamic conditions provided in the hot spot area, ? precision in composing slag products These are analysed and described in this paper based on technical results from selected test campaigns over the years and thermodynamic considerations. The electromagnetic properties of DC arcs beneath the electrode have been studied by CFD simulation. The calculated result enables us to understand some interesting technical phenomena observed. The heat balance has also been considered based on data obtained from test campaigns and heat balance calculation.

Jan 1, 2004

By F. Henríquez, V. Iriarte, L. Vinnett, J. Yianatos, F. Díaz

Metallurgical characterizations of the collective (Cu/Mo) and selective flotation plants were carried out in Minera Los Pelambres, Chile. The selective plant allows the valuable minerals of Cu and Mo to be separated. The evaluation involved two surveys consisting of metallurgical sampling as well as residence time distribution (RTD) measurements to determine load distribution. The RTD data were obtained in real-time by means of the radioactive tracer technique. In addition, metallurgical data was reconciled and supported by effective residence times. In the collective plant, a performance comparison of parallel rougher circuits was carried out, which included a bank of six mechanical cells of 250 m3 and banks of nine mechanical cells of 130 m3. In the selective plant, the Cu and Mo evolution along the plant was evaluated. The results in the selective plant allowed for performance evaluation of mechanical and pneumatic cells in primary flotation. In both plants, mineral losses were evaluated and their relationship with circuit configuration (cell types and circuit layout) was determined. The metallurgical characterization was a powerful tool to evaluate circuit performance and to detect improvement opportunities at industrial scale.

Jan 1, 2015

By C. Carreno, A. D. Gonzalez Escarcega, M. A. Neri, A. Martinez –Villafane, O. Cobarrubias-Alvarado

"Waspaloy is a superalloy used to manufacture some aeronautical parts subjected to high temperatures and stresses. During thermo-mechanical processing cracks are generated, causing some parts to be rejected. In order to determine the causes of these cracks, this alloy was characterized using techniques such as chemical analysis, optical microscopy, scanning electron microscopy, and EDX analysis. Heterogeneous grain sizes in the microstructure cause a non-uniform strain distribution in these parts, creating cracks in zones with different grain sizes.IntroductionNickel-base superalloys are important materials for high-temperature service applications. The manufacture of components from these materials is typically based on solidification or powder-metallurgy processes [1]. Solidification techniques comprise either the direct casting of parts or the casting of ingots which subsequently undergo a series of thermo-mechanical-processing steps to refine the microstructure. During solidification, microsegregation is usually unavoidable. The primary solidification product is a disordered nickel solid solution with an fee crystal structure (?). In many alloys, the material which solidifies last is a mixture of ã and an ordered fee phase (? '). In prototypical nickel-base superalloys, the ?'-phase is Ni3(Al,Ti) [2-3].Waspaloy is a superalloy that is used in demanding high-temperature environments in which good creep and fatigue resistance are required. One of the most common applications of Waspaloy is for turbine engine rings. To ensure the required mechanical properties, the rings are usually forged and heat treated (Figure 1). Two distinct types of microstructures are usually found to be attractive for such applications: a) A microstructure with a grain size of ASTM 10 to 14 for tensile strength, ductility, and resistance to crack nucleation in low-cycle fatigue; or b) A microstructure with a grain size of ASTM 4 to 8 required for creep strength and resistance to crack propagation [4]. Because it is impossible to refine the grain size through heat treatment, a skillfully designed forging process is crucial for the control of the grain size and, hence the properties of the forged ring [5-6]."

Jan 1, 2012

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951