Search Documents

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

By Wm. H. Woodhead

Improved methods of mining have accompanied the introduction of mechanical loading, of which there are a great many varieties, but this multiplicity of mining brings new problems and greatly increases the importance of managing over a few years ago. Few mines operating today have been opened with the intention of mechanizing throughout. The problem of mechanization is to change over a mine heretofore operated by hand methods and to select machinery that will fit the old system with the least number of changes, the aim being not to disrupt or to completely change the original plan. The organization of mechanical and electrical forces is a problem in mechanical loading, and each individual mine presents its own problems. Plans which may succeed in one mine may fail in another and upon the management rests the responsibility of deciding the best method in each case.

Jan 1, 1930

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By Wenxue Chen

This paper presents a new type of bolt with full thread and uniform strength, and fabricated with a Glass Fiber Reinforced Polymer (GFRP) bolt-making machine designed by the authors. The mechanical performance of the new bolt is assessed with strength tests conducted with the bolt in acid, alkaline and saline water conditions, with increasing concentration. The purpose is to test the new GFRP bolt?s mechanical performance in harsh conditions, especially metal mines with acid or alkaline environments. Comparison of the color, weight, size and antistatic ability of the GFRP bolt before and after it is immersion in solution is presented. Changes in tensile and shear strength, torsion, and anchoring force were evaluated in the laboratory. The results show that the mechanical properties of the GFRP bolt are more sensitive in alkaline than in acid and saline water. However, the loss ratio of mechanical properties of the GFRP bolt is very small according to the results of tensile and shear strength, torsion and anchoring force. The new bolt can be useful for applications in acid or other harsh mines.

Aug 1, 2013

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By József Faitli, Imre Gombköto, Barnabás Csoke, Tamás Magyar, Beáta Oláh, Sándor Nagy

"Raw materials are among the main building blocks of a growing economy. Without raw materials, no matter whether it is primary or secondary, production is not possible. Products with high added value require special materials. Recently, worldwide production of some important raw materials mainly comes from a handful of countries, for example: China (Rare Earths Elements (REE)), Russia, South Africa (Platinum Group Elements (PGE)), Democratic Republic of Congo (Cobalt), etc. In the EU as well as in Hungary, the importance of the so called 14 critical raw materials has been recognized. Within the frame of the TÁMOP-4.2.2.A-11/1/KONV-2012-0005 - CriticEL project, the Institute of Raw Materials Preparation and Environmental Processing in cooperation with the Institute of Mineralogy and Geology of the University of Miskolc are working on the exploration of the primary and secondary sources and developing innovative preparation technologies of critical raw materials in Hungary. The research work showed in this article, focused on the recovery of critical materials from LCD TVs and monitors. There are high deviations in different literatures regarding to concentrations of critical elements in displays (e.g.: indium), probably because of the differences in production year, producers and recovery technologies. During the research - described in this study - a well specified sample of quite large amount of displays had been used. The exact place and shape of the ITO (indium-tin oxide) layer were determined by SEM analysis. The applied preparation technology was developed based on the results of our investigations and by technologies found in the literature. The developed process accomplishes two main parts: the mechanical preparation (mainly the liberation of different display layers, removal of liquid crystal) and the acidic dissolution of indium."

Jan 1, 2014

By Hideyuki Takahashi, Taro Aichi, Kazuyuki Tohji, Makoto Muramatsu, Rie Sato

"There are several ways to condition lead-based alloy anodes for zinc electrowinning: electrochemical treatment, chemical treatment and physical treatment. Two advantages of physical treatments are their productivity and variety. In this report, physical treatments, including blasting with silica, alumina, steel grit and cut zinc wire, were tested. The laboratory tests confirmed there were differences in the formation of anode scales during electrowinning and in the suppression of lead dissolution from the anodes. With an increase in the surface roughness, the misfit between the PbC""2 and the MnC>2 was mitigated and the anchor effect was promoted; these effects resulted in dense Mn oxide scales on the anode.IntroductionZinc is widely used for hot-dip zinc plating and for die casting alloys. As a supplier of materials, we have endeavored to produce zinc that is economical and contains as little impurity as possible. As a result of our efforts, a technology for consistently providing special high-grade (SHG) zinc has been established. However, as seen in the issuance of the Restriction of Hazardous Substances (RoHS) Directive, public awareness of the industrial impact of heavy metals on the environment has been heightened. Increasing efforts to control environmentally sensitive substances will be necessary for our production processes.Electrolytic SHG zinc is produced by electrodeposition in an acidic solution with a Pb-Ag or Pb-Ag-Ca alloy for the anode and an Al alloy for the cathode. Pb alloy anodes are widely used because of their excellent durability; however, they are a source of Pb, which is the main impurity of the product."

Jan 1, 2012

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By J. R. Rendón

Cylinders of commercial aluminium alloy 6063 were homogenized under different conditions. The experimental results indicated that the general mechanical behaviour as related to curves of 0.2% yield strength, ultimate tensile strength and Brunnell hardness versus homogeneizing process is the same in both cases. The mechanical properties as compared to those required by plant specifications, tend to be better with increasing values of % Mg2Si in the alloy, as expected. The electron microscopy investigations revealed that in both homogeneizing processes the resulting microstructure consist of significant spheroidizing of the alpha phase (AlFeSi) and fine-needle type structure of beta phase. The alpha phase was also present in a Chinese type scripture. Furthermore, the slow cooling within the furnace resulted in the nucleation and growth of Mg2Si precipitates generally along the grain boundaries.

Jan 1, 1997