Search Documents

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),

Jan 1, 1966

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.&apos; The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.&apos; The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.&apos; Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By J. P. Myers, A. H. Flagg, E. S. Mardock, J. L. P. Campbell, J. M. Terry

The development process for the use of radioactive tracers as a means of locating zones of permeability is discussed. The general techniques for the safe handling of radioactive materials is given as developed by the Lane-Wells Co. and Well Surveys, Inc. The prob1em and. successes with tracers in waterflood systetns, oil and gas injection profiles, fracture sand tracing, squeeze (ement tracing. lost circulution, and cement top localion are discussed and illustrated. INTRODUCTION The exact location of the permeable zones lying within the productive horizon has been a major problem faced by the petroleum engineer for decades, and it has been a problem which has seldom been solved with certainty. Reservoir engineers usually have to incorporate a question mark in their estimates of future reservoir performance because of blanks in the core data. Although the use of radioactivity or electrical logs for the estimation of porosity has been of great assistance in furnishing a record for the reservoir engineer, this application of logging data has not completely solved the problem. In short, the industry needs an in-situ well surveying method which can locate and estimate the permeability of the zones existing within a given pay section. The initial development work with radioactive tracers has been towards filling the need for permeability information. Progress to date permits the location of permeable zones with a qualitative estimate of their relative importance with respect to permeability. The calibration of the method is still incomplete. but present development work on tracer preparations, borehole effect correction factors, and instrument limitations give a promise of quantitative "permeability profiles" in the near future. The development work on the radioactive tracer method discussed here began several years ago in the laboratories of Well Surveys, Inc., in Tulsa. At the outset of this work, three approaches to the problem were visualized as follows: 1. A fluid carrying a soluble, chemically inert, gamma ray emitting isotope is pumped down the borehole and out into the permeable zones of the formation. The greater gamma activity of the permeable zones thus permits them to be differentiated from the impermeable zones which contain no active tracer. It was found difficult to obtain a tracer material which was chemically inert. Absorption to some degree was noted in all experiments. Also, it proved impossible to hold the tracer near the horehole where it could be logged. 2. A fluid carrying a soluble, gamma ray emitting isotope is pumped down the borehole into the permeable formations. In contrast with proposal 1, above. the tracer is chemically active with the fluids and materials in the pore spaces of the permeable zones. The permeable zones are thus indicated by their higher radioactivity level. The main difficulty in this proposal was finding a tracer material which would not be absorbed by shale as well as in the permeable porosity. Very little field work was done with this system. 3. Radioactive particles suspended within the injection fluid are pumped down the well. As the fluid enters the permeable formations, the radioactive particles are filtered out on borehole wall. The permeable zones are differentiated from the impermeable by the gamma ray activity deposited on the formation wall.

Jan 1, 1956

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.&apos; In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.&apos; Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years&apos; experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8&apos;9&apos;11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth&apos;s magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR&apos;s of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert&apos;. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR&apos;s, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.&apos;s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Justo Germán Ramón Rojas

El presente texto describe la importancia de la gestión de seguridad en valor y ventaja competitiva de la empresa para así disminuir las pérdidas económicas causadas por los siniestros, accidentes y daños a la salud del trabajador. La forma de evaluación de la cultura de seguridad es mediante los indicadores de clima y cultura de seguridad y el trabajo responsable y comprometido del equipo de SSO.

Mar 1, 2013

By Américo Pérez

La política ambiental de Centromin Perú S.A. promueve el aprovechamiento de los recursos minerales sin comprometer la capacidad de las futuras generaciones para satisfacer sus necesidades y desarrollo. En ese sentido, los objetivos de la empresa comprenden la protección de la salud y seguridad pública, la prevención del medio ambiente a largo plazo y el uso productivo de las áreas afectadas, retornándolas a su estado inicial. Por ello, el presente trabajo señala los avances en la resolución de los pasivos ambientales de la ex unidad de Casapalca y el Programa de Adecuación Ambiental de la unidad de Morococha, en actual operación.

Sep 13, 2001

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

By Marcos Figueiredo Nicolau

O fluxo de produção da VSB contempla um alto-forno a carvão vegetal e uma aciaria elétrica. Para melhor sincronizar a programação do alto-forno (AF) e a do forno elétrico (FEA) é importante ter um conhecimento prévio de quais corridas do FEA usarão gusa líquido. Foi desenvolvido este projeto visando auxiliar na tomada de decisões da programação do AF e do FEA, a partir de uma simulação da logística de movimentação das panelas de gusa em cenários pré-determinados. Dentre as respostas que podem ser obtidas por essa contribuição técnica destacam-se: o número mínimo de panelas que devem ser utilizadas no circuito, quantas e quais corridas do forno elétrico serão atendidas com gusa líquido e a contribuição de cada meio de transferência de calor para a perda térmica total.

Aug 1, 2018

By Peter Smith

One New Change is a landmark retail / commercial development in the City of London. Integral to the structure is the three double storey basement from which the building is serviced. The building construction involved a ?top down? (up down) construction technique to give programme benefits. In addition, the planning authority stipulated that 10% of the energy demand had to be met by Renewable technology. Cementation Skanska has not only delivered the foundation package - comprising secant piling and foundation bearing piles including Cemloc® plunged columns - but, alongside subcontractor Geothermal International, also installed a 1.7MW ground source heating and cooling system using Energy Piles® and open?loop wells to provide the renewable energy. The works were successfully installed and completed within a tight programme, and within the logistical constraints imposed by an inner-city location, concurrent demolition works and multi contractor involvement in the basement construction.

Jan 1, 2010

By Albert Ladd Colby

PAGE I. Introduction,...........577 11. PRocess of Manufacture. 1. American Specifications. 2. Foreign Specifications, . ......... 580 III. Chemical Properties. I. Chemical Composition: (a) American Specifications ; (b) Foreign Specifications. 2. Chemical Analysis: (a) American Specifications ; (b) Foreign Specifications ; (c) Number of Analyses Required ; (d) Sample for Analysis ; (e) Check-Analyses Impracticable ; (f) Rejection Solely on Variation in Com-&apos; position,............581 IV. Physical Properties. 1. Drop-Test and Drop-Testing Hachine: (a) American Specifications ; (b) Foreign Specifications ; (c) Limits in Deflection. 2. Tensile Test: (a) American Specifications; (b) Foreign Specifications ; (c) Test-Pieces are not Representative ; (d) Specified Tensile Strength is Affected by the Section ; (e) BpeciBed Tensile Strength is Often Inconsistent with Specified Chemistry ; (f) Specified Tensile Strength is Often Inconsistent with Specified Elongation ; (g) Amount of Tensile Testing Required is Excessive ; (11) Conclusions. 3. Dead-Weight Test: (a) American Specifications; (b) Foreign Specifications; (c) Number of Tests Specified. 4. Bending-Test: ((1) American Specifications ; (b) Foreign Specifications,..........589 V. Section. 1. American Specifications. 2. Foreign Specifications: (a) Templets ; (b) Sample Piece of Rail; (c) Allowable Variation from Templet,...........601 VI. Weight. 1. American Specifications. 2. Foreign Specifications,. . 603 VII. Length. 1. American Specifications. 2. Foreign Specifications, . . 604 VIII. Drilling. 1. American Specifications. 2. Foreign Specifications, . 604 IX. Finish. 1. American Specifications. 2. Foreign Specifications, . . 50.5 X. Branding. 1. American Specifications. 2. Foreign Specifications : (a) Data to be Rolled in Raised Letters on Web of Rail ; (b) Marking of the Blow-Number on Each Rail; (c) Additional Marking and Painting of Rails,........605 XI. Inspection. 1. American Specifications. 2. Foreign Specifications: (a) Prior Notice of Rolling; (b) Free Access to the Works ; (c) Cost of Inspection, Analyses and Tests to be Borne by the Manufacturer ; (d) Rails after Inspection by Manufacturer to be Sorted into Lots Prior to Inspection by the Engineer ; (e) Disposition of Rejected

Jan 1, 1907