Search Documents

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Martin Herrenknecht

The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge to provide efficient traffic infrastructure, such as a modern public transportation system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are also essential. Additionally, supra-regional transportation routes such as long distance water diversion schemes are the challenges for the future. All these projects are as demanding as they are characterized by a tight time schedule.

Jan 1, 2010

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By Christopher Bambridge

The Washington State Department of Transportation (WSDOT) is constructing a new tunneled route under Seattle to replace the existing State Route 99, Alaskan Way Viaduct (AWV), which follows the historic waterfront for several miles. The viaduct separates the businesses that rely upon the tourist trade from the down-town area. The reconnection of the city to the waterfront areas will occur following the completion of the SR99 Re-placement program that replaces the aging structure that was severely impacted by the 2001 Nisqually earthquake, with a state-of-the-art, twin-deck highway with a world record-breaking 17.4-m (57.3-ft) bored tunnel. Constructed in the 1950s, the double-tiered viaduct is nearly 3.2 km (2 miles) long and runs parallel to city?s waterfront. The viaduct, which is partially supported by the seawall, is a vital local and regional transportation link and carries about 110,000 vehicles each day. The seawall, built from concrete and timber in the 1930s, extends along Seattle?s waterfront and supports the soil behind it. Studies in the 1990s showed that the viaduct was nearing the end of its useful life, apparent by its exposed rebar and weakened columns. The 2001 Nisqually earth-quake further damaged the viaduct, forcing WSDOT to temporarily close it for inspection and limited repairs. The viaduct and nearby seawall are vulnerable to an-other earthquake and continue to show signs of age and deterioration. Following a collaborative process, WSDOT developed the following guiding principles to the viaduct replace-ment:

Sep 1, 2013

By M. J. Hrebar

In the summer of 1990, a study was conducted to document large tractor (i.e., Caterpillar Dl1N) utilization in surface coal mining. The tractors were found to be utilized as primary production machines and in combination systems with blast casting and draglines and blast casting and excavator/truck systems. In addition, dozers were used to prebench ahead of a primary dragline system. The study also established ranges and averages for Dl1N operating costs and mechanical availability. Based on simulated production of various tractor dozing applications, the potential for low cost coal stripping was suggested (Hrebar, 1991). A follow-up study, also funded by Caterpillar Inc., was conducted in the summer of 1991 to determine actual production rates in two dozer stripping applications. These actual production rates would then serve as a foundation for estimates of stripping costs. This paper presents the results of the studies in a contour and a cast application.

Jan 1, 1992

By W. K. Chan, R. Lahaie

"The Suncor Oil Sands Mine located north of Fort McMurray, Alberta, produces about 80000 m' per day of tailings waste which must be disposed of economically in an environmentally acceptable manner. To date, this has been accomplished by impounding the high water content tailings wastes behind large dykes, many of which approach 100 m in height .The dykes are constructed using suitable overburden material stripped prior to the mining of the oil sands feed and/ or the coarse sandy fraction of the tailings waste itself. Although the above is common practice at many mining operations, the large volumes handled and the resultant costs require designs to be meticulously fine-tuned toward the optimum. As a result, considerable effort is expended on planning, designing and construction, and performance monitoring. The lack of precedent experience (Suncor pioneered oil sands mining), coupled with the realities of long, harsh winters and a variety of troublesome site conditions and construction materials, has led to some very unique dyke construction.This paper overviews current tailings disposal plans as welt as some of the key issues related to the design, construction and performance of these large dykes."

Jan 1, 1988

By S. P. Vanka, B. G. Thomas, S. Sivaramakrishnan

"During the continuous casting of steel, transient 'flow events can be very important to the generation of quality problems, such as shear entrainment, surface level fluctuations and bubble entrainment. These phenomena can be better predicted using Large Eddy Simulation (LES) models than the K-E models, which have been extensively studied. In this work the turbulent transient flow in a water model of a continuous caster has been both simulated using LES models and measured using Particle Image Velocimetry (PIV). The results of PIV and LES have been compared to validate the LES model and also to enhance the understanding of the prominent transient features of the flow field. The flow near the top surface in PIV was found to contain periods of 5-1 Os when the velocities were three to four times their mean values, which is of importance to the shear entrainment of the liquid flux. In both simulation and PIV the upper roll structure is found to change chaotically from a single large recirculation structure to a set of distinct vortices. The inlet swirl in PIV is seen to persist more than halfway across the mold, causing a characteristic staircase velocity vector pattern when viewed in a plane parallel to the wide faces. The lower rolls in PIV are significantly asymmetric for very long periods of time (- I-hour) and go through a repeating sequence of features. One of these features involving a short circuit between the upward and downward flow in the lower roll is also seen in the simulation and is of significance to bubble entrapment.IntroductionThe turbulent flow through the nozzle and in the mold of the continuous caster has been studied extensively using computational Reynolds Averaged Navier Stokes (RANS) models of turbulent flow [1,2]. Defects, such as internal inclusion of liquid fl4x through surface shear, pencil pipe defects due to bubble entrapment, surface defects due to level fluctuations are caused by transient flow phenomena oc'curring in the mold. These phenomena can be better predicted using transient Large Eddy Simulation [3] or ""LES"" models."

Jan 1, 2000

By D S. Collins, Z Hosseini, I Pinnock, Y Toya

Microseismic monitoring is regularly used in the mining and geotechnical industries to provide detailed information about rock mass response to operational activities. This paper implements a variable 3D velocity model (VM) at a North American hard rock mine with the aim of further improving the accuracy of seismic event locations. A collapsing method is also used to help analyse two individual seismic event clusters at another North American hard rock mine. In the first case study, the location accuracy of events is shown to improve by moving from a conventional single VM to a variable 3D VM that accounts for voids and different geological domains. The modal average for the event location accuracy improved from 14 m to 5 m when the 3D VM was used. Additionally, the single VM failed to locate 26 per cent of the seismic events that were located by the 3D VM. In the second case study, the distribution of seismic events was further enhanced by using a collapsing method that highlighted planar structures. The collapsing method was performed on two large event sequences that occurred in close proximity and identified different seismic event distributions. One aftershock sequence aligned along a plane, suggesting an activated structure, while the other large event sequence had a more 3D distribution of events, suggesting a complex stress redistribution on smaller structures.CITATION:Pinnock, I, Collins, D S, Toya, Y and Hosseini, Z, 2016. Large event sequence analysis and 3D velocity models for seismic event location accuracy, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 879–884 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By J. R. Maxwell

In 1970 expansion was completed increasing mill capacity from 2,000 to 3,000 T.P.D. Actual grinding capacity is 3,400 T,P,D. at a grind of 60% -200 mesh,The ore bodies are vein type, containing about 12% sulphides, with mill heads averaging 2.25% Cu, 0.015 oz.Au, and O.4O oz, Ag. per ton.Summary and Conclusions:During the period Jnnuar-1 1971 to December 1973 inclusive the use of large cells at Opeminka have shown that metallurgy is comparable to when using conventional cells, Operating and maintenance costs are lower, An on stream analyzer with reagents controlled by computer, are being assessed further.Opej1atljn Of Cells:!lo cell level adjustments are required when tonnage is adjusted 20 to 25%.Depending on mill heads and grade of concentrate reagents are adjusted to the first rougher for metallurgical control. Reagents to second rougher and scavengers are seldom adjusted as feed to this section has a maximum variation of about 0.2'~ Cu.Power – Maintenance and Space Requirement :Our total power consumption for 3,400 T.P,D. flotation circuit for operation and air supply is 280 H.P. Previous power drawn using conventional cells was 400 H.P. at 2,000 T.P.D.Total maintenance costs for flotation circuit has averaged $1,100.00 per year for the 3 years of operation, this cost should remain constant.Floor space required for cells and walkways is 2,000 sq.ft.

Jan 1, 1974

By J. Kallioinen

The development of mechanical flotation cells has resulted in larger and better cells. This has led to flotation banks with only a few units, even in large-scale operations. This equipment development makes the old operational considerations ineffective. The flotation cell must be considered as a single reactor unit capable of handling specific tasks and getting excellent metallurgical performance. The result of the unit reactor concept development was the new large TankCell that comes in sizes up to 113 m3 (4,000 cu ft). The TankCell construction includes new modified rotor-stator designs, new tank geometries and a froth-handling capability independent from subprocesses taking place in the pulp (i.e., air addition). The conventional idea of a single flotation cell type for fine, intermediate and coarse materials does not give optimal results. Optimal flotation of coarse and fine particles needs different mechanism designs, impeller tip speeds and different froth control objectives.

Jan 1, 1995

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

By M. Churchill, V. R. Degner

"Over the past two decades, declining ore body grades, increased operating costs and increased construction costs have provided an incentive for the development of progressively larger flotation machines. As a consequence, the 60 to 100 cubic foot flotation machine of the l950's and l960's is being rapidly replaced by large volume machines, with a resulting improvement in the flotation machine specific capacity (TPH processed per square foot floor space), specific power (HP per TPH processed) and process control simplicity. The recent development, and satisfactory plant evaluation, of the WEMCO 1000 cubic foot flotation machine provides the means by which further economic and operating advantages may be incorporated in high tonnage mill applications.The systematic development of the large 1000 cubic foot flotation machine, and its subsequent performance evaluation in beneficiating metalliferous ores (copper, zinc and iron) will be reviewed in this paper and recently completed plant results will also be provided."

Jan 1, 1982

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By R. L. Guerguerian

Critical fasteners are described as they apply to the specification, manufacture, and assembly on large grinding mill bolted joints. The importance of adequate design methods, related joint diagrams and pivot analyses, and special emphasis on the quality of manufacturing and the tightening procedures in the field, are discussed; all in an effort to ensure high availability plant operation.

Jan 1, 2001

By John Berney-Ficklin

Large scale grinding mills can reduce both capital and operating costs for concentrators. These mills can be effectively used, but they must be free from design and manufacturing deficiencies if they are to reach their full potential and avoid costly downtime. This paper presents the evolution of today's complex grinding mill specifications and discusses the most important items to look for when buying new equipment. It emphasizes the need to monitor specification requirements during design and manufacture. It also discusses the growing trend to have grinding mills fabricated in overseas plants, and the importance of recognizing this when preparing specifications.

Jan 1, 1987