Search Documents

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.&apos; Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.&apos;&apos; As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By William D. Klopp

A study was conducted of the tensile and creep properties of are-melted and electron-beam-melted tungsten over the temperature range 2250° to 4140°F. The tensile and creep strengths vary with pain size, the finer -grained materials being stronger. The activation energy for transient creep at 2250° to 3500°F is 95,000 cal per (g)(mole), while that for steady creep at 3300o to 4000°F is 141,000 cal per (g)(mole). At 2875o to 3300°F the apparent activation energy for steady creep decreased with decreasing temperature. It is suggested that cross slip is rate controlling during transient creep, while dislocation climb is rate controlling during steady creep above 3300° F. ALTHOUGH considerable data have been generated on the high-temperature tensile properties of powder-metallurgy tungsten,1 relative few data have been published on the properties of are-melted2 or electron-beam melted tungsten.3 Furthermore, the available data show a fairly large amount of scatter at high temperatures. The effects of structure and purity have not yet been defined, aside from observations that high-purity electron-beam (EB)-melted tungsten3 and single-crystal-plasma-flame tungsten4 are weaker than less pure powder-metallurgy tungsten. The creep behavior of powder-metallurgy tungsten has been studied, but no data are available on the creep behavior of tungsten consolidated by melting. Green5 found that powder-metallurgy tungsten exhibited linear creep at 4082° to 5072°F with an activation energy of 160,000 cal per (g) (mole). The similarity of this activation energy to that of 153,000 cal per (g)(mole) for volume self-diffusion6 suggests that recovery of strain hardening by dislocation climb is rate controlling in this temperature range. In studies at 4800°F, Sutherland and Klopp7 concluded that grain size significantly affected the creep behavior of commercial powder-metallurgy materials. This grain-size effect was suggested by sherby,8 although the opposite relation had been reported for aluminum.&apos; The purpose of the present study was twofold: first, to provide baseline data on high-temperature tensile and creep properties of are-melted and EB-melted tungsten for concurrent tungsten alloy studies, and, second, to determine the phenomenolo-gical effects of structural and purity variables on the high - temperature mechanical properties of tungsten. EXPERIMENTAL The are-melted tungsten materials were prepared by melting sintered 1-1/4-in.-diam electrodes into 2-1/2-in.-diam by 5-in.-long ingots. The are-melting facility has been described previously.&apos; Eight ingots were melted, machined, and hot-extruded at

Jan 1, 1965

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder&apos; showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.&apos; The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.&apos; Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others&apos; found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer&apos; found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By S. I. Liu

THE effects of strain histories, consisting of several prestrains in opposite directions, on the flow and fracturing characteristics of metals determined in a final test have been investigated previously.&apos;" Such strain histories vary from a single prestrain in tension or compression to the number of strain cycles leading to fatigue failure.&apos; Between these two limits, various strain histories could be visualized and some can be attained readily. One such example is a strain history consisting of a first prestrain in tension of various magnitudes and a second prestrain in compression also of various mag-nitude. In this investigation the strain history was extended to the combination of these two limits, i.e., a single prestrain in tension or compression followed by balanced strain cycles of a selected magnitude e, = k0.12. It was found in this case that only compressive initial prestrains could be investigated with sufficient accuracy.* Such strain histories can be considered also as (low cycle) fatigue tests of a metal subjected to various amounts of cold working. It appears from previous publications that cold working within a wide range of reductions usually raises the un-notched fatigue strength of many metals.&apos;-&apos; This effect, however, has been found to be inconsistent and sometimes reversed for other metals?.7 Furthermore, Ludwik reports that the yield strength of cold-worked specimens may be reduced by cyclic strains, while that of materials without cold work is generally increased in the initial cycles." " In addition to the above tests, a study was made of the effect of intermediate re-solution heat treatment on low cycle fatigue behavior. Such anneals should eliminate the strain hardening induced by the cyclic strains. As far as their effect on the fracture characteristics is concerned, a few previous tests seemed to indicate that the damage resulting from cyclic strains is retained only partially after heat treatment." A further investigation was made in which one specimen was subjected to repeated unbalanced tension cycles in which the strain interval was approximately $ 0.013. This repetition of plastic tension damages the material slightly. This result appears to confirm Ludwik&apos;s observations." " Commercial 3/4-in. rod of the aluminum alloy 24ST4 was selected for this investigation. The material was subjected to the following treatments before machining: 1—Re-solution treatment at 920" ± 10°F for 45 min, 2—water quench at room temperature, and 3—aging for four days at room tem-perature.? The treated material then was machined to desired specimen contour and tested. A coolant was used during machining to minimize any artificial aging effects of heating during machining. In some cases the 24ST4 specimens were reheat treated after having been strained. In these cases, the heat treatment was the same as the re-solution heat treatment described above. Procedure As shown in Fig. 1, threaded end specimens with a minimum diameter of 0.266 in. and a contour radius of 2 in. were used for prestraining to an axial compressive strain ranging from 6, = —0.10 to E, = —0.48. For large prestrains, two consecutive corn-

Jan 1, 1952

By J. P. Hammond, C. J. McHargue, S. E. Adair

Cold-rolled sheet textures have been determined for binary solid solutions of aluminum, columbium, tantalum, and zirconium in titanium. An alloy containing 3.8 pct Al had a (0002) [10101 texture, whereas alloys with the other elements had rotated (0002) [10101 textures similar to that of iodide titanium. THERE have been relatively few studies of the effect of alloying on deformation textures. A second element may be present in the base metal in solid solution and/or as a second phase. The literature offers no satisfactory explanation for the effects of solid solution alloying on textures noted thus far. For example, there is no satisfactory explanation of the difference in the textures of copper and a brass. The most complete study of the effects of solid solution alloying on deformation textures has been that of Brick, Martin, and Angier.¹ These investigators reported that the copper texture was retained by alloys of copper with up to 30 pct Ni, less than 5 pct Zn, less than 2 pct A1 or Co up to the limit of solubility. Copper containing more than 5 pct Zn, more than 2 pct Al, or the maximum soluble concentration of tin, silicon, or manganese showed the deformation texture of a brass. Bakarian² reported that additions of 0.20 pct Ca to 99.98 pct Mg or 2.0 pct Mn plus 0.15 pct Ca to magnesium resulted in entirely different textures than for the pure magnesium. The texture obtained for high-purity magnesium sheet showed the basal plane to be concentrated parallel to the rolling plane. The texture obtained for the alloy containing 0.20 pct Ca had the basal planes concentrated in elliptical areas whose centers were tilted 15" from the center of the pole figure toward the rolling direction. This split basal orientation was even more pronounced in the alloy containing 2.0 pct Mn and 0.15 pct Ca. Fuller and Edmunds" studied the rolled sheet textures in a zinc alloy containing 1 pct Cu and 0.01 pct Mn. The basal pole figure of this alloy contained a region of strong concentration not found in the pole figure for pure zinc.&apos; In the above cases, results were discussed in terms of possible changes in slip and/or twinning systems and critical shear stresses. However, there were no experimental data to relate these speculations with the observed textures. It has been suggested that the deformation textures of titanium, zirconium, and beryllium could be directly ascribed to their low c/a ratios. The complex deformation mechanisms of titanium" also have been suggested to be characteristic of hexagonal close-packed metals with low c/a ratios. The purpose of this investigation was to study the cold-rolled sheet textures in binary titanium-base a alloys in which the c/a ratios were greater than, less than, and about the same as the c/a for iodide titanium. The annealed textures of these alloys will be reported in a subsequent article. Materials and Methods The chemical analyses of the metals used in this investigation are given in Table I. The alloys were prepared as 15 g buttons on a water-cooled copper block in a vacuum arc-furnace. The furnace was evacuated to pressures of the order of 10.&apos; mm Hg, flushed with 99.98 pct pure argon, and melting was carried out in 0.2 atm pressure argon. Each button was remelted until radiographs and chemical analyses indicated complete solution of the solute elements. All buttons were forged and homogenized 72 hr at 500°C. The buttons to be rolled were ground and etched to sizes and shapes suitable for the rolling

Jan 1, 1954

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By R. J. Arsenault

The yield drop that occurs in tantalum, Cu-AZ. and Ag-Al was investigated as a function of strain rate and at several temperatures. From the strain-rate dependence of the yield drop an activation volume was calculated and found to agree with that obtained from differential strain-mte tests. The temperature dependence of the yield drop can he explained in terms of the parameter temperature divided by activation volume. The yield drop is attributed to the rapid multiplication of dislocations during their motion. THE yield-point or yield-drop (upper yield stress minus the lower yield stress) phenomenon has been the subject of numerous investigations1-9 in both bcc and fcc metals. Also, there is no dearth of theoretical explanations10-20 to account for the yield-point phenomenon. The present explanations can be divided into two categories: the concept of dislocation locking and subsequent unlocking and the concept of multiplication of dislocations due to their motion. The Vottrell10,11mechanism of locking and unlocking, as applied to bcc metals, is the best known of the three proposed locking mechanisms. The two additional mechanisms, short-range order (SRO)7,16,17 and Suzuki-type locking,14,15 have been employed to account for the existence of yield points in fcc metals. The experimental evidence supporting the locking of dislocations, especially in bcc metals, is well-established. The dependence of the yield point on interstitial concentrations,&apos; the kinetics of strain aging,2 and the observations by electron-transmission microscopy18 are some of these experimental results. The number of experimental observations supporting dislocation locking in fcc metals is not as extensive as in bcc metals. The unlocking of dislocations, which actually is supposed to account for the yield drop, is by no means well-established by experimental results for either bcc or fcc metals. The similar temperature dependence6 of the yielding and plastic flow is one of the experimental factors that cannot be explained in terms of the unlocking of dislocations. The mechanism based on the rapid multiplication of dislocations has been proposed by several investigators. 18-20 Johnston and Gilman19 have proposed a detailed model of yielding, which was later employed by Hahn21 to predict quantitatively the yield drop in iron. This mechanism was discussed in a previous paper22 and several limitations were pointed out. In the same paper it was shown that an activation volume could be obtained from the strain-rate dependence of the yield drop and that a correlation existed between the activation volumes obtained from the yield-drop tests and from differen-

Jan 1, 1964

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases&apos;-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-&apos;&apos; Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By C. S. Barrett

Measurements of impact hardness of ß-brass are reported for a wide range of temperatures. Abrupt softening is observed when temperatures are raised above 425ºC, accompanied by abrupt widening of deformation bands in the deformed samples. Current theories of these effects, and of the lack of twinning, are discussed. HARDNESS1 and flow stress2 of a sample of ß-brass at room temperature depend upon the temperature from which the sample is quenched. It is believed that the state of order in the superlattice is responsible for this dependence—not the order within individual domains, which reaches near-perfection during the quench from any temperature, but the size of the domains which is presumed to be a minimum in the hardest samples, those quenched from temperatures near the critical disordering temperature of 468°C. Measurements of impact hardness made over a range of temperatures and microstructural studies of samples deformed both rapidly and slowly over a range of temperatures, reported herein, should be of aid in reaching a more complete understanding of the underlying factors controlling the properties of the disordered body-centered-cubic material and the ordered material. It appears that such data have not

Jan 1, 1955

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.&apos; Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

By E. F. Bailey, L. S. Birks

The effect of stress on the austenite to ferrite transformation in carbon steel was studied by X-ray diffraction techniques. Tensile stress was found to cause reorienta-tion of austenite above the transformation temperature, to accelerate equilibrium conditions at the transformation temperature, and to cause precipitation of large carbides at a critical value of stress. IN the past, a number of papers&apos; have discussed the effect of stress on the austenite to martensite transformation at relatively low temperatures. In general, it has been shown that tensile stress induces some transformation at a given temperature, while compressive stress retards the transformation. Very little work has been reported on the effect of stress on the transformation from austenite to ferrite plus carbide near the A, point in steel. One of the few papers in the literature2 reports an increase in A1 of about 1°C in pearlitic steel upon the application of tensile stress. In this paper, the effect of tensile stress on eutec-toid steel at, and above, the A, point was studied in

Jan 1, 1956

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".&apos; that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By Dell P. Williams, Howard G. Nelson

The tensile behavior of magnesium single crystals at a temperature of 26º ± 2ºC was investigated at varying pressure levels from 760 to 8 X 10-8 tow. For crystals deformed at a constant linear strain rate of 0.061 min-1. there was no apparent effect of the vacuum environment down to 10-8 torr. However, from a vacuum of 10-5 torr down to the lowest pressure attained (8 x 10-8 tor,), the effect of the vacuum environment was to increase the strain at the end of the first linear (or easy-glide) stage and to decrease the slope of this stage; the magnitude of this effect was found to be dependent on pressure. The slope of the second linear stage was also decreased at the lower pressure levels; however, this effect appears to be caused primarity by the vacuum effect on the first linear stage. The magnitude of the vacuum-environmrnt effect was also found to be dependent upon strain rate. The reduction in flow stress at 5 x 10-8 torr, as compared to the stress in air, was obserced to be about 10 pct for a strain rate of 0.0250 min-&apos; and 70 pct for a strain rate of 0.67 min-1. No systematic effect of pressure on the critical resolvled shear stress was observed. The data interpreted in terms of a modified form of Mott&apos;s work-hardening mechanism for hexagonal metals. It has long been known that surface conditions influence the mechanical behavior of materials. Roscoe 1 demonstrated the importance of surface conditions on mechanical behavior by testing cadmium crystals with oxide layers. He found that the "apparent" critical resolved shear stress for cadmium was increased approximately 2.5 times by the presence of an oxide layer 1000 atoms thick. The magnitude of this effect was dependent on film thickness with crystals having films less than 20 atoms thick still showing a definite increase. This observed strengthening could not be attributed to any strength of the oxide film because of 1) the thinness of the films and 2) an observed increase in the flow stress as deformation proceeded. Harper and cottrel12 obtained similar results on zinc crystals which had been etched and steamed to give artificially thick oxide films. However, in the course of this study, they also carefully examined the very early stages of plastic flow for zinc crystals which in one case had been electrolytically polished and in the other had been lightly etched to produce a thin film. They then found that the critical resolved shear stress for both surface treatments of the crystals was actually identical but that the etched crystal exhibited a much more rapid initial hardening rate. This had not been noted previously. This result indicated that, in fact, the film caused an increase in the stress for continuation of slip, rather than for the initiation of slip. Lipsett and King3 investigated the effect of evaporated gold films on the plastic behavior of cadmium single crystals. For large angles (=75 deg) between the specimen axis and the normal to the slip plane, they found that the stress-strain curve of the coated specimen always lies above that for a clean specimen. The shear strain at the end of the first linear stage was greater in clean specimens than in coated specimens and the slope of the second linear stage was

Jan 1, 1965

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson&apos;s ratio, and Young&apos;s modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young&apos;s modulus, s is Poisson&apos;s ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman&apos;s measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958