Search Documents

By Walter C. Holmes

IN the recently published book entitled "Man in a Chemical World," by A. Cressy Morrison, the several pages discussing explosives were included in the chapter on "Serving Industry." Such a classification is entirely correct, as blasting explosives function only as a tool for accomplishing certain useful work, a tool which is completely destroyed in one use. Explosives are so important to industry and to modern society, in fact, that it seems impossible to imagine the existence of civilized nations without access to commercial explosives as ready servants. Two main types of explosives are now in use, the low-velocity or deflagrating type, such as black powder, which is adapted for use in coal mining and other applications where a slow, heaving effect is desired, and high explosives of the dynamite type,

Jan 1, 1938

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By V Cullinan, D Buchanan

The Brunswick plant is located in Costerfield, approximately 40km east of Bendigo in central Victoria. Crushing, grinding, gravity gold concentration and flotation methods are used to produce a saleable gold concentrate and an antimony-gold flotation concentrate. This paper discusses the improvements made within the processing plant which have resulted in a 99% increase in throughput over nameplate capacity of 6 250 average tonnes per month to 12 445 average tonnes per month and increases of 12% gold (from 2007 average of 78% to 2014 average of 90%) and 16% antimony recovery (from 2007 average of 79% to 2015 average of 95%). This combined effort has resulted in an increase of equivalent gold ounces (AuEq oz) produced from 2010-2014 of 15 872 to 82 574 – a 66 702 increase.AuEq oz= Au oz +Sb t × Sb (US$/t)Au (US$/oz)CITATION:Buchanan, D and Cullinan, V, 2015. Improvements in bi-metal production at the Brunswick Plant, Costerfield, in Proceedings MetPlant 2015, pp 267–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Pradhan GK

Blasting is one of the most important operations involved in surface coal mining. The removal of over-burden waste in surface coal mines of India had experienced many improvements in terms of blasting, explosives selection, blast design, equipment selection, deployment. etc. Two case studies of very large surface coal mines have particular importance in their blasting operations. Both these units have been equipped with large capacity excavating machines, hauling units and also have some difficult mining situations. Blasting is done in benches in close proximity to human dwellings and over coal seams developed by underground methods with problems of high wall stability etc, as well. The various steps taken to improve the blasting operations ensure smooth operation of the equipment to meet the targetted coal production.

Jan 1, 1991

By Kelvin K. Wu

A coal waste disposal dam failed on Buffalo Creek near Saunders, West Virginia, on February 26, 1972. This accident resulted in the loss of 125 lives, left over 4000 people homeless, and resulted in millions of dollars in damage to several downstream communities. As a result of this tragic event, major changes occurred in the mine waste disposal practices used by the U.S. coal industry. This paper summarizes changes in U.S. coal-waste disposal practices in the nearly 35 years since the Buffalo Creek dam failure and identifies safety issues that need to be addressed for continued improvement. While many organizations and individuals have played roles in the improvements that have occurred, this paper focuses on the role played by MSHA and its predecessor agencies.

Jan 1, 2006

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By John A. Meech, J. G. Paterson

Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation system where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level used in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate pulp.

Jan 1, 1979

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By David R. Macedon

"Through the years, a wide variety of dust control methods have been utilized at mineral processing operations. While some have been successful, many have been highly ineffective. Dust Control systems currently in use include baghouse systems, fog systems, surfactant spray systems, and foam dust suppression. While baghouse systems can be effective, they are capitalintensive and costly to operate and maintain. Chemical dust control programs can be very effective. However, if applied incorrectly, they can have detrimental effect on mineral recovery. Thus, many operations utilize a combination of baghouses and water, often with limited success.Recent advancements in surfactant and polymer chemistry have resulted in substantially improved chemical dust suppression programs. These products range from non-corrosive surfactant/humectant combinations for road dust control to foam-based systems for crushers and transfer points, to advanced polymers for pile binding and soil stabilization. These advances are discussed in detail, citing results from fieldwork in the precious and base metals industries.INTRODUCTIONThe global nature of the mineral processing industry presents a unique set of challenges. Traditional thinking would tell us what works in one place should work in another. This could not be further from the truth in the area of dust control. We learn very quickly that there are a number of factors that can affect the efficiency and success of a dust control program and that these factors are not all chemical or equipment related. Some of these factors include facility maintenance, product selection, water quality and characteristics, and economic considerations.What has been learned from past experience is that each mineral processing plant presents a unique set of factors that will affect the ability to create an optimal dust control program. This paper presents a myriad of treatment options that will highlight the advancements in chemical dust suppression products and equipment."

Jan 1, 2004

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis- charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed arid built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, anti not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct the grinding and classification test program. It was the author's privilege

Jan 1, 1939

By M Bird, B Oats, M Sganzerla

Mining operations are continually aiming to reduce operating costs to improve plant profitability. One way in which the Cannington operation sought to achieve this was by increasing the wear life and reducing the energy consumption of their flotation mechanisms. This was made possible using Outotec’s FloatForce mechanism. The FloatForce mechanism has been developed by Outotec over a six year period involving both CFD modelling and rigorous site testing. FloatForce delivers improved air dispersion and cell agitation efficiency; as such it can be operated at lower rotor tip speeds when compared to Outotec’s previous mechanism.Cannington trialled three FloatForce mechanisms in a train of ten OK38 zinc roughers. The mechanisms’ rotational speed was reduced by 10% compared to the previously installed MultiMix mechanisms. The purpose of the trial was to quantify the energy saving and assess whether there was any reduction in plant metallurgical performance.The trial was successful with FloatForce delivering a 17% reduction in power, an improvement in wear and improved recovery. Analysis of pre and post-installation metallurgical accounting data showed the following:The FloatForce installation resulted in a recovery increase of zinc to zinc final concentrate of 0.4 – 4.0%*The FloatForce installation resulted in a recovery increase of lead to zinc final concentrate of 0.0 – 0.3%*There was no statistically significant change in silver recovery to zinc final concentrate that can be attributed to FloatForce**95% confidence interval (CI) using multiple linear regression models.The Cannington operation is now in the process of further optimizing its power consumption and wear savings by changing the remaining OK38 zinc and lead rougher float cells to FloatForce mechanisms.CITATION:Bird, M, Oats, B and Sganzerla, M, 2015. Improvements in flotation cell maintenance, power consumption and operation at South32 Cannington, in Proceedings MetPlant 2015, pp 230–245 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By J. L. Arola

Since start-up of fluxed pellet production in August: 1987, the Minorca Mine has made a number of process changes to improve pellet quality and productivity. Quality improvements include: 1. Installation of a contraction t:ester. 2. Installation of on-line calcium and silica analyzers. 3. Process autocation changes. Productivity improvements include: 1. A second fluxstone storage bin and feeder. 2. A new vacuum pump and disc filter. 3. A filter aid addition system. 4. Enclosing the filter cake reclaim feeder. 5. A new grate bar cleaner.

Jan 1, 1989

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By C. S. Davis

In being asked to present this paper on the improvements in loading and hauling equipment and the effect on unit costs, Mr. Van De Water, your program chairman, stated that his reason for coming to a contractor was due to the wide experience of, and I quote: "a large contracting firm using a variety of equipment on varying types of earth moving jobs." We people in Utah Construction Company are flattered that Mr. Van De Water singled out our Company for this assignment. Utah Construction Company's participation in open pit mine stripping antedates the 1920's, when overburden was being removed from copper ore in Bingham Canyon, Utah. Our first stripping con¬tract for the Copper Company was finished in 1912. Since that early beginning, Utah has, as a contractor, been engaged to strip and mine iron ore properties, coal properties, copper properties, uranium properties, phosphate,-gypsum, limestone and dolomite properties. And, as you know, the Company has become a major producer of iron ore from Company-owned open pit mines. Utah Construction Company has been instrumental in the evolution of open pit mining tools. Some of the first tools were the old wood and coal fired stream shovels which had to be fired hours before a shift started to insure a full head of steam, providing power to excavate with the then large 1-1/2 cubic yard buckets. Today, Utah's strip mining is done, with 18 cubic yard and 10 cubic yard crawler shovels. Yesterday's horse and mule drawn, iron wheeled wagons, with 1 and 2 cubic yard capacity, which were hand dumped by removing the false bottom, one 2 x 4 at a time, have been replaced by today's- 50-ton capacity, hydraulic, rear dump trucks and giant 40-ton coal haulers. Utah Construction Company used the early fresnes and wheeled scrapers which were horse and mule drawn. Often, an operator holding too tightly to a handle was thrown into his horses when a hard spot turned the scraper, a contrast with today's 20 and 25 cubic yard, self-powered diesel and diesel electric Gargantuan rigs; with power controls that relieve the operator of practically all physical work. This Company has pioneered many of today's advances in equipment with shop made prototypes, features of which were adopted and elaborated upon by equipment manufacturers.

Jan 1, 1959