Search Documents

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Lachezar Tsotsorkov

Being a mining company, Assarel-Medet has a significant impact upon the environmental components. In order to meet the legal requirements and the requirements stipulated by the effective permits as well as to reduce the environmental imprint throughout the years, the policy of the company to implement a number of projects to improve the environmental components quality and the environmental state in the company?s region. The projects associated with atmospheric air quality management and reduction of the impact exercised by Assarel-Medet JSC by implementing various measures to eliminate the potential sources of the impact, preventive and rehabilitation initiatives as well as organizational and administrative activities are among the most important ones. A stable improvement of atmospheric air quality in the region and minimization of the company impact upon the ground air state in the region was observed in the period from 2005 to 2012 due to the applied measures. This project is a contribution to the environmental protection, in particular to atmospheric air protection, by applying integral monitoring and modeling methods to identify the negative impact by the mining companies and plan measures to reduce and restrict it as well as to improve the quality of the environment and living area of people working and living in the impact range as an element of sustainable development.

Aug 1, 2013

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Shuji Owada, Keisuke Yasukawa

Electrostatic and/or high tension separation has been used for the separation of rare metal bearing minerals, foods, industrial wastes and so on. Since the separation is achieved by the difference mainly in surface conductivity of particles, the efficiency in humid circumstances is very low, and then, the applicability is considerably limited. We applied the following two-stage pretreatment technique to the separation process, which involves (1) adjustment of surface wettability by adsorbing surfactant on the particle surface and (2) control of the surface conductivity by spraying with electrolyte aqueous solution. The addition of this pretreatment technique has been found to have a great advantage over conventional methods. Separation efficiency is achieved even in humid circumstances and selectivity can also be obtained between insulator minerals. The selectivity is very similar to that of flotation in wet process. This separation technique will be applied not only to mineral processing but the processing of industrial waste such as electric and electronic waste materials.

Jan 1, 1995

By G. Deschenes, W. Yen

Ammonium thiosulphate is a non-cyanide lixiviant for gold leaching. The major problem is the high reagent consumption. A combination of 0.3M (NH4)2S2O3, 0.03M CuSO4, 3M NH3 was used to leach a copper-bearing gold ore at pH 10.2 for 24 hours. 30 kg/t of thiosulphate was consumed. Oxygen and copper species were found to be responsible for thiosulphate decomposition. The thiosulphate consumption could be reduced to around 17 kg/t by adding chelating agent, reducing copper sulphate concentration to 0.001 M and replacing CuSO4 by NiSO4. The increase of pulp density might reduce the thiosulphate consumption to around 17 kg/t. By regulating the oxygen supply, the thiosulphate consumption could be reduced to 10 kg/t.

Jan 1, 2002

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By B. A. Kutlin

29% of the total ore mined in the Russian Federation for copper production is finely disseminated copper-zinc-pyrite ores of the Ural Region. Physical and chemical characteristics of pyrite copper-zinc ores make for difficulties in obtaining high indices during processing. At present, the authors have elaborated the technology to improve the quality of copper concentrates up to 20.0% for the ones obtained during pyrite copper-zinc ore processing (based on the example of the ore mining and processing enterprise ?Uchalinsky GOK?, Russian Federation). There are examples of use of fair-sized pneumo-mechanical flotation machines by modernization of processing plants. Keywords: copper-zinc-pyrite ores, Ural region Russian, selective flotation, pneumo- mechanical flotation machines

Sep 1, 2012

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

"Mine ventilation is in every underground mine a crucial process to ensure mine safety as well as acceptable working conditions. On the other hand is also a major cost factor depending on air requirement and air resistance. Due to the fact that the special layout of mines develop over time, ventilation systems change as well. This may result in complex systems which are suffering severe problems and low efficiency. With attention to the mine safety and costs, ventilation systems have to be controlled repeatedly and optimized continuously to fit changing conditions. The project “Improvement of ventilation systems in narrow vein mines” has been commenced with measuring and data collection in the Bogala Mine, Sri Lanka. This over 150 year’s old graphite mine consists of about 20 levels. The resulting ventilation system is highly complex and suffers problems like high temperatures and humidity as well as a mixing of fresh and used air on lower levels. To solve these problems and to optimize the system the complete ventilation system had been measured on-site first. The gained data have been used for simulations to develop and select an optimal and cost efficient solution. OBJECTIVE As an important process in mining ventilation is a major cost factor and can determine the economic feasibility of a mine. Due to the production mine layouts develop over time and mines increase in size and depth while the ventilation system becomes more complex and may suffer severe problems and inefficiency. Therefore mine ventilation systems have to be controlled and optimized regarding the general requirement of mine safety and health of the miners as well as the costs. Depending on the deposit type, depth, mining method, climate and as well corresponding laws and regulations the possible solutions are varying strongly. The work carried out paid special attention to the improvement of ventilation in narrow vein mines in tropical climate, in this case the graphite mine “Bogala” in Sri Lanka, South Asia."

Jan 1, 2015

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Xinyang Wang

It is believed that sulfur and volatile matter contents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal - three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014

By Min Chen, Lei Xu, Weijun Huang, Shuai Zhang

For the purpose of extending the service life of MgO-C bricks used as linings of vanadium-extraction converters, the effect of Fe addition on properties of MgO-C bricks was investigated. The results showed the addition of Fe could effectively improve the sinterability of the oxidized layer of the MgO-C refractory at 1400°C due to the effect of FeO (formed by oxidation of Fe) on formation of MgO-FeOss and modification of the microstructure, and excellent corrosion resistance against vanadium containing slag was also obtained due to the increase of compactness of the oxidized layer and concentration of FeO in the oxidized layer. Consequently, it is considered that MgO-C brick by introducing the new phase of Fe is a favorable substitute of MgO-C refractory to be used as linings of vanadium-extraction converters.

Jan 1, 2015

By Jorge Cárdenas Miranda, Hector Espinoza

Currently in open pit mining in Peru with double bench, it is a challenge to optimize fragmentation in the drill rows near to the slopes to ensure the performance in the loading and haulage operation along with the process in the plant. That is why the present paper addresses a previously unanalyzed variable on the effect of the discontinuity plane on the fragmentation results. From the numerical mathematical models applied through algorithms in advanced computational tools such as Elfen, it was quantified the improvement in fragmentation results as P80 through a correct pre-split plane both in its extension as well as in its width. The first results show an improvement of 30% in the P80 and ensuring the quality of the walls without damage to the matrix of the final wall. The basis developed in this paper is based on the concept of wave reflection in the free face zones where greater efforts are presented for fragmentation, a similar theory is presented in the variation of initiation sequences that seek a greater area of reflective planes in the form of "V". Cases were evaluated with a percentage of compliance of the pre-split planes from 0 to 100% evaluating the impact on the results and correlated with field information explaining the behavior and validating the benefit. From the quantification of the benefits, this work opens the possibility of focusing resources on optimizing the pre-split process to achieve an improvement in the fragmentation results, giving a greater tool in the decision to optimize the blasting process.

Feb 6, 2023

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023