Search Documents

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. Saki, J. F. Brune, J. W. Grubb

"Researchers at the Colorado School of Mines have studied the influence of headgate side ventilation controls near the longwall start-up room on the formation of explosive gas zones (EGZs) in underground coal longwall bleeder ventilated gobs. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) researchers developed a Computational Fluid Dynamics (CFD) model to study the formation of methane-air mixtures in the gob, start-up room, and bleeder entries. The relative change in size and location of EGZs are examined in response to ventilation controls in the headgate side bleeder entries near the start-up room. Modeling suggests that adjustments to the ventilation controls can be made to minimize the size of the EGZ. However the EGZ may form in or around active working areas regardless of the ventilation control settings. Research found regulators on the crosscuts into start-up room and first entry inby can force air into to crosscuts outby the start-up room causing more air to flow through the gob. INTRODUCTION Underground longwall mine ventilation systems may operate with either a bleeder ventilated gob or a progressively sealed gob. Bleeder ventilated gobs must meet the standards for safe operation of the bleeder system by examining bleeder system effectiveness. As defined in the United States Mine Safety and Health Administration (MSHA) Program Policy Letter (PPL) No. P13-V-12 (MSHA 2013), the pillared area or gob is “any area where a reduction in pillar size has occurred during retreat mining” and includes the “caved and broken material, the interstices within the caved material, and the open spaces surrounding the caved material.” The PPL further states that the intended purpose of ventilating the gob is “to protect active workings from the hazards of methane accumulations …” The requirements for operating a bleeder system as stated in The United States Code of Federal Regulations (CFR 2013) Title 30 §75.334(b) is to pass ventilation air though the gob “and to continuously dilute and move methane-air mixtures [from the gob] away from active workings and into a return air course …” where the concentration cannot exceed 2 percent methane (CFR 30 § 75.323). Further clarification of the bleeder system as described in the PPL states the following: “A bleeder system includes the area from which pillars are wholly or partially recovered, bleeder entries, bleeder connectors, and all associated ventilation control devices that control the air movement through the area. Bleeder entries are air courses designed and maintained as part of the bleeder system.”"

Jan 1, 2015

By M E. Pierce, T V. Garza-Cruz

Rock mass strength and brittleness generally have a significant impact on both cavability and fragmentation. Variability in these properties across a panel or block footprint is of particular interest because stronger units have the potential to significantly impact cave shape. This paper describes how FLAC3D™ was used to examine the impact of variability in rock mass properties on predicted cave performance to aid in assessing potential risks associated with the proposed design.A case study orebody was subdivided into a number of domains to reflect the heterogeneity of the rock mass at the scale of a proposed inclined cave. The results suggest that the presence of stronger units has the potential to impact cave shape significantly in the southern half of the cave footprint and could increase the potential for cave stalling at shallow depths. If this unit is stronger and less brittle than expected, an overhang is predicted to develop in the southern half of the inclined cave at depth. The effective hydraulic radius is significantly reduced due to the overhang in the south, and the cave could eventually stall at shallower depths in the north.CITATION:Garza-Cruz, T V and Pierce, M E, 2016. Impact of rock mass strength variability on caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 359–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. Kemeny, R. Fuentealba, C. Rodriguez, F. Fernandez, M. Rocha, T. BoBo

"Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations. The goal of the mine is a mill throughput of 95,000 tonnes (104,720 tons) per day (TPD). Based on this goal, run-of-mine fragmentation analysis was conducted for four blasting designs resulting in powder factors of 0.44, 0.54, 0.64, and 0.94 kg/t. The powder factor of 0.44 represents a standard blasting design, while the 0.54 and 0.64 kg/t designs are high-energy blasts specifically to assist with mill production. The 0.94 kg/t design was investigated for the one geologic unit with very high strength. The results of the run-of-mine fragmentation analysis was then input into a crushing and grinding simulation model to predict the mill throughput for the time periods of 1-5 years and 6-10 years. The results indicate that certain blast designs are able to achieve the 95,000 tonnes TPD (104,720 tons TPD) goal, while other blast designs were not. A standard blast design with a 0.44 kg/t powder factor, for example, was not able to achieve the throughput goal, while a design with a 0.64 kg/t powder factor was able to achieve the goal in both the 1-5 and 5-10 year time periods. INTRODUCTION In recent years, mathematical modeling in conjunction with mineral characterization has been widely used as a method for the design and optimization of comminution circuits. The Run-of-Mine Particle Size Distribution (ROM PSD) is a function of rock properties and design parameters of the blast and has a significant impact on the crushing and grinding treatment circuit. Traditionally, design of the grinding treatment is estimated using only the F80 value instead of the full distribution of sizes in the feed, but the finer sizes have great influence on the treatment of a grinder, particularly in the SAG mill."

Jan 1, 2015

By Massimiliano Zanin, William Skinner, Keith Quast

With the scarcity of fresh potable water on mining sites, particularly those in arid and remote regions, the use of sea water is being contemplated and actually used at a number of mineral concentrators worldwide. The use of sea water, with its associated high dissolved solids content and ionic strength will affect all aspects of processing (e.g. frothing and froth stability, buffering capacity for pH control, solubility of minerals and corrosion of media and equipment). Selective depression of pyrite is more difficult in sea water due to the increased lime addition to achieve a high pH. This results in a reduction in molybdenite recovery. The use of grinding media with various chromium contents and its effect on subsequent Cu and Mo flotation has been investigated in the current study, with both grinding and flotation testing conducted in artificial sea water. Pulp chemistry (pH, Eh and DO) have been logged during grinding, and flotation testing was conducted on subsequent slurries. The flotation results show that the system is remarkably robust and able to cope with wide ranges of pulp chemistry parameters. The effects of artificial sea water on the surfaces of minerals during grinding have been examined using X-Ray Photoelectron Spectroscopy

Jan 1, 2014

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By F. D. Agrensa, J. Hadjigeorgiou, E. Storimans, S. J. Thorpe

Reinforcement and surface support are part of an integrated system that transfers and shares loaduntil the excavation surface is stabilized or until the ground support system fails. Steel mesh is the most popular primary surface support element in underground hard rock mines in Canada. Mesh straps are a secondary surface support that provide additional containment as they distribute the load between and across the reinforcement elements. This investigation addresses the role of steel properties, and in particular steel chemistry, in the long-term performance of mesh and mesh straps when exposed to an aggressive corrosive environment. It reports on comparative accelerated corrosion studies to compare the resistance to corrosion of different surface support elements. This has significant implications on the choice of surface support and the anticipated rehabilitation requirements.

Oct 9, 2024

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining impacts those properties is important in developing effective management practices to control erosion during reclamation. Soils from undisturbed areas, roughly graded mine spoil, replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated to determine impacts on soil hydraulic properties. Field and laboratory studies were conducted to determine soil hydraulic properties, including particle-size distribution, organic matter content, and saturated hydraulic conductivity. WEPP simulations and risk analyses were performed on the soil hydraulic property data to determine the impacts of changes on soil erosion. The hydraulic properties of the soils in each representative area have significant differences due to the mining and reclamation practices at the mine. WEPP simulations show that the potential for soil erosion increases due to mining activities disturbing the soil. WEPP simulations also indicate that the potential for erosion may return to pre-mining levels over time with effective revegetation practices.

Feb 27, 2013

By C. S. Todd, R. L. McNearny, S. Dun, P. Clark, P. W. Conrad, X. Liu, J. Q. Wu, H. Rhee, W. J. Elliot

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining affects these properties is therefore important in developing effective management practices to control erosion during reclamation. To determine the impact of mining activities on soil hydraulic properties, soils from undisturbed areas, areas of roughly graded mine spoil, areas with replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated. Field and laboratory studies were conducted to determine the soil hydraulic properties of the four representative areas, including particle-size distribution, organic matter content and saturated hydraulic conductivity. Using this data, Water Erosion Prediction Project (WEPP) simulations and risk analyses were performed to investigate mining’s effects on changes in soil erosion potential. Significant differences were seen in the hydraulic properties of the soils in the representative areas due to the mining and reclamation practices at the mine. The WEPP simulations show that the potential for soil erosion increases as a result of mining activities disturbing the soil. The simulations also indicate that the erosion potential may return to pre-mining levels over time with effective revegetation practices.

Jan 1, 2015

By R. Eggert

Since the discovery of high temperature superconductors has led to extensive interest and conjecture regarding their potential to change contemporary technology, discussions of the impact on the metallurgical and other industries have naturally arisen. In this paper we present data showing the possible impact of these developments on the materials related to the fabrication and proliferation of devices based on superconductor materials. We observe that the largest volume of effort with LTSC will be for the demonstration of high power devices while applied research relating to processing will remain the principal HTSC activity. We also note that in the next decade copper consumption in the US is expected to remain essentially at the current level while the need for Nb and Sn,; two major components of LTSC, will grow at a faster rate both in the US and the world. Although the use of superconductor-based magnetic separation is anticipated to increase, no major impact of these components on the metallurgical industries is expected.

Jan 1, 1990

By C. Birch

"A mineral resource royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In South Africa, this payment is made to the State as holder of the mineral rights (The Mineral and Petroleum Resources Royalty Act of 2008). The principle purpose of this research paper is to identify if the State is benefitting from the mineral resource royalty by considering its impact on seven individual Witwatersrand gold mines.For this study, a simple financial optimiser model was created in Microsoft Excel that links the ore flow, block listing and the cash flow (excluding or including the cost of the mineral resource royalty). Mixed integer linear programing (the Excel Solver function) is utilised to optimise either profit or NPV (at 9% and 12%) by adjusting the cut-off grade.The impact on each of the seven mines mine was different but overall R7.9 billion is estimated to be paid in mineral resource royalty over their expected remaining lives. Due to the cost of the mineral resource royalty and increasing the cut-off grades, the total revenue decreases by R10 billion. A significant portion of this lost revenue would have been paid to the State in the forms of other taxation including company income tax which decreases by R2.8 billion. It is recommended that an industry wide investigation be conducted to determine if the resource royalty is adding to the State’s revenue, or destroying value including premature job losses. IntroductionTaxation of mining companies has become a very topical subject in the context of the postapartheid South African economy. There have been increasing calls for equitable re-distribution of mineral asset wealth for the benefit of all South African citizens and not just to an elite few. As part of the Mineral and Petroleum Resources Development Act (MRDPA) of 2002, the Mineral and Petroleum Resources Royalty Act of 2008 was introduced and came into effect in 2010 (South African Revenue Services, 2008). A mineral royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In the case where the holder of the mineral right is the State, then this payment is made to the State (Cawood, 1999). Studies on the potential impact of the mineral resource royalty on the minerals industry have been conducted during the formulation of the Act and subesquently. These include Cawood and Macfarlane (2003), who suggested a cap of no more than 3% (Cawood and Macfarlane, 2003), as well as Cawood (2011), who predicted rising cut-off grades and thus reducing mineral reserves. In 2013, Grobler completed a Masters in the Faculty of Economic and Management Sciences at the University of Pretoria and concluded that the impact of the mineral resource royalty on the economy is positive. She stated that the royalty has caused operating expenses to increase, but this does not appear to be significant. Furthermore, she stated that the royalty has not affected the way the mining industry operates (Grobler, 2014)."

Jan 1, 2016

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By Dallas Grubbs

Agenda ?Growth Projections ?Economic Indicators ?Mining Equipment Growth ?Tire Supply ?Michelin Actions to Increase Capacity ?Michelin?s Challenges & Recommendations

Jan 1, 2006

By G. Viggiani, J. Bel, H. Wong, N. Losacco, D. Branque

"Within the framework of the European project NeTTUN, the Laboratory of Civil Engineering and Building Sciences of ENTPE in Lyon (France) is in charge of a large experimental campaign to investigate the impact of tunneling on neighbouring piled structures. For this study, an original reduced-scale (around 1:10) physical model of EPBS is used. This ""1g"" laboratory model is able to reproduce the main features of the excavation method. For this new experimental program, the miniature EPBS advances inside a large tank filled with a model soil (dry sand), in which instrumented piles were pre-installed. In this paper, the authors describe briefly the original 3D device and present results concerning the impact of tunneling on a single pile located above the tunnel. Different tunneling face pressure are studied in connection with the practice. Machine parameters, pile solicitations and stress-strain behavior of the soil mass monitored under real time conditions are discussed. INTRODUCTION When tunnels are constructed in urban areas, they often come close to pre-existing structures, such as pile foundations. Perturbations of tunnel construction on these neighbouring structures must be considered during design and construction of the tunnel. Ground movements due to tunnelling may induce bending moments, lateral and vertical loads, settlements and lateral deflections in the piles, which may lead to structural damage or failure of the piles or the supported structure. The interaction between piles and a tunnel in construction is a complex three dimensional problem. To date, several experimental approaches have been carried out to analyse the effects of tunnelling on piled foundations (Bezuijen et al., 1994, Loganathan et al., 2000, Jacobsz et al. 2004, Lee and Basset, 2006, Marshall and Mair, 2011, ). These different studies carried out in the laboratory on 1 g or centrifuged models aim at a better understanding of tunnel - piles interaction and a quantification of the influence of each dominating parameter on the structural responses. Parameters like foundation type (single pile, group of piles) and geometry, relative tunnel – pile position, volume loss induced by tunnelling, ground characteristics, pile loading history were considered. However, most of these experiments were carried out under plane strain conditions by modelling the volume loss due to tunnel excavation by decreasing the tunnel diameter or the radial support pressure. As a result, these models do not adequately account for the variations of settlements both in the longitudinal and the transverse direction, which can induce significant flexional and torsional effects on the structures. These effects are particularly critical and detrimental in the case of historical monuments."

Jan 1, 2016

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014