Search Documents

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 4, 2010

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Somasundaran P., M. Vasudevan, Z. Dai, D. R. Nagaraj, T. Bhambani, P. Patra

Historically, efficient beneficiation of ultramafic ores has been challenging, partly due to a lack of clear scientific understanding of the effects of Mg silicates, particularly fibrous serpentines, on selective Ni recovery. Recent research at Columbia-Cytec as a part of a Vale JDP project has led to new insights into the mechanistic aspects of the adverse effects of Mg silicates. Our research has provided strong evidence to support the hypothesis that the adverse effects of Mg silicates are mediated through their large influence on pulp rheological properties, far more than any other pathway. The severity of the effect of Mg silicates is predominantly dependent on the aspect ratios of Mg silicates. For example, the pulp viscosity increases dramatically with increase in the fibrous nature of the gangue mineral leading to poor Ni separation. Various ways by which the suspension rheology affects flotation sub-processes, with implications for remedy are discussed. The insights and results have served to develop (or construct) a phenomenological model to adequately explain all of the ore flotation data, particularly the Mg silicate transport to the froth phase and the concentrate.

Jan 1, 2011

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By D Thornton, R Hodson, D Sprott

Blast fragmentation size distribution and thus blast design have been found to have a direct impact on the load and haul cycle through excavator dig time and bucket payload. Previous studies have demonstrated that by reducing the excavator dig time and increasing bucket payload, significant improvements can be made in both productivity and unit cost. Simulation work reported in the literature indicates that a 20 per cent improvement in dig time may result in only a three per cent improvement in load and haul productivity and unit cost. At the same time, a ten per cent improvement in bucket payload will directly translate to a ten per cent improvement in load and haul productivity and unit cost. Based upon these findings, extensive laboratory and field work have been undertaken in the past to correlate blast fragmentation distribution to bucket payload. In contrast, the literature reports limited studies quantifying the impact of blast fragmentation on excavator dig time. Field work was conducted at Placer Dome Asia PacificÆs Granny Smith Mine (Wallaby Pit) in Western Australia, concentrating on quantifying the impact of blast fragmentation on the dig time of a Liebherr 994 hydraulic excavator (shovel attachment with 14 m3 bucket). Fragmentation was assessed for each truck load of material using the Split Desktop system, while the excavator cycle analysis was conducted manually. Measured fragmentation P80 (fragment size at which 80 per cent of material passes) values ranged from 200 mm to 1200 mm. The field study investigated the impact of various fragmentation parameters (P20, P50, P80, cumulative per cent passing 250 mm size fraction, and uniformity index) on the average and total dig times. The results indicate that the fragmentation P80 provides the best correlation to average dig time (total dig time divided by the number of bucket passes to load a truck). The total dig time was found to be dependant upon the fragmentation P80 and the number of bucket passes to fill a truck. Monte Carlo simulation results, based upon these relationships, indicate a 26 per cent improvement in average dig time and a 12 per cent to 46 per cent improvement in total dig time (bucket passes ranging from 4 to 8), with a change in fragmentation P80 from 600 mm to 200 mm.

Jan 1, 2003

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016