Search Documents

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America. The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By L. R. Plitt, A. J. Neale, B. C. Flintoff

"INTRODUCTIONThis is not a technical paper in the normal sense. It is an informal document which is intended to share the results of some recent cyclone research with our colleagues both in operations and in research.PILOT PLANT FACILITIESFigure 1 is a schematic of the closed circuit hydrocyclone pilot plant testing facility at the University of Alberta. In this figure the system is configured for some experimental work on wide angle cyclones which was recently completed. The rig is designed to study cyclones in the approximate range of 10 cm to 20 cm diameter. Notable features include the variable speed feed pump, the magnetic flowmeter and pressure sensors on the cyclone feed line and the travelling launder which permits simultaneous sampling of both product streams.ORGANIZATIONFor organizational convenience the subject matter has been divided into three parts:(1) Peculiar Partition Curves(2) Wide Angle Cyclones(3) Rope DischargePECULIAR PARTITION CURVESMuch of the initial empirical mathematical modelling work on cyclone classifiers dealt with homogeneous ores. A homogeneous ore is one in which all particles have substantially the same apparent density, or where one phase is very clearly predominant. In contrast, a heterogeneous ore is one in which there are at least two different density classes, each making a significant contribution to the ore composition. (Particle shape similarity is always assumed.)One of the problems which can arise when analysing the overall solids partition (selectivity, Tromp, etc ... ) curve for a heterogeneous ore is the peculiar shape which may be observed, when compared to partition curves for homogeneous ores. This is not an unusual occurrence and it has been documented by Lynch and Rao, Finch and Laplante and Larsen and Spring. The purpose of this section is to identify those operating conditions which may give rise to peculiar partition curves."

Jan 1, 1986

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By E. A. Cleveland

A glance at the map discloses the fact that the Pacific Great Eastern railway either traverses or crosses some of the most important rivers of the province: the Squamish with its branches the Stawamus, Mamquam and Cheakamus; and the Green, Lillooet, Birkenhead, Fraser and Quesnel rivers. Each of these and some of their tributary streams, having their ?sources and upper reaches in the higher altitudes in regions of abundant snowfall, is capable in greater or less degree of furnishing water under suitable heads for the economic production of power. Beginning at its present terminus at Squamish the railway has the only hydro-electric development within its territory among the whole list of streams mentioned. A 225 horsepower installation at the edge of the East branch of the Squamish river, using water from Stawamus river, a branch of the former, under a head of 418 feet, is a modest beginning. Two or three additional sites, where water may be used under somewhat similar heads, may be found on this little stream. Next above Squamish, along the route of the railway, is the Mamquam, a long tributary of the Squamish from the eastern slopes. It has a drainage area of something like 130 square miles with widely varying discharges of from less than 50 to about 14,000 cubic feet per second. The preliminary investigations so far have disclosed no suitable storage sites, so the Mamquam may be regarded as a small continuous power stream - probably less than 1000 horsepower.

Jan 1, 1925

By V. S. Gischig, G. Preisig

Hydraulic stimulation of deep reservoirs is an essential procedure for developing engineered/enhanced geothermal systems (EGS), but also in other Geo-energy contexts. The goal is enhancing permeability to such a degree that fluid flow rates within the reservoir are sufficiently high for an economically productive reservoir. Two fracture stimulation mechanisms are distinguished that may occur concurrently during the hydraulic treatment: 1) During hydro-fracturing (HF) new tensile fractures are propagated from the borehole by means of a fluid pressure overcoming the minimal principle stress d3 plus the tensile strength T0 of intact rock. In case of a pre-existing fracture oriented normal to d 3 , the fracture can be opened by exceeding d 3 only. Fluid injection is performed via small packed intervals for creating a stack of hydraulic fractures. 2) During hydro-shearing (HS), over-pressure induces slip along pre-existing fractures that are favourably oriented in the stress field for reactivation in shear. Such stimulation is usually performed in a large packed interval or in an open borehole. Which mechanism occurs predominantly during stimulation depends on the rock mass structure and in-situ stress field, but also on the orientation of discontinuities intersecting the open-hole section and thus being pressurized. Both mechanisms also differ in how they affect fracture permeability. While permeability gained by HS is mostly irreversible due to rearrangement of asperity contacts accompanied with shear dilation, permeability enhanced during HF reduces nearly reversible after pressurization unless proppant is used to ensure permanent apertures. In this contribution, we critically discuss the pros and cons of both mechanisms regarding efficiency of enhancing permeability and the associated hazard of induced earthquakes based on literature review and numerical modelling. We review literature that reports on how much permeability required for productive EGS reservoirs and how much permanent permeability can be gained by stimulation. We also compile information regarding the degree of seismicity induced during HFor HS-dominated stimulation procedures, together with conceptual studies that reveal characteristics of seismicity associated with the two mechanisms. Many observations and models indicate that HF may have a higher tendency of being aseismic, while felt seismic events are usually associated with HS. Further, we present a hydro-mechanically coupled fracture flow model that investigates, if and to what degree the stimulation strategy can be designed such that one of the two mechanisms is evoked and dominates over the other. It shows that HS may dominate in presence of larger persistent fractures nearly optimallyoriented in the stress field, even if HF is attempted in short packed intervals. The model further demonstrates that stress transfer during HS promotes the development of permeability across an anisotropic layer of the stimulated rock instead of a large volume. Hence, the study sheds light onto the feasibility of creating productive EGS reservoirs in crystalline rock at several kilometres depths.

Jan 1, 2015

By T. Belem

The main objective of this study is to better understand the effect of underground CPB placement conditions on its microstructural, hydro-mechanical and geochemical properties. To reach this objective, three PVC columns, each 3 m high, were built, and were filled with CPB material. The columns allow simulating undrained (UD), half-drained (HD) and fully-drained (FD) conditions along with the measurement of resulting self-weight consolidation settlement of the CPB. Bleed and drainage waters were also collected from each column for geochemical analyses (pH, Eh, EC, SO42- content). After 90-days of curing time, a total of sixty CPB samples were cored from the backfill columns and subjected to uniaxial compression tests followed by physical characterization (Gs, void ratio, water content, degree of saturation, specific surface area). The results showed that the total drainage water and the maximum observed settlement occur mainly within the first 72 hours after the columns are filled. The corresponding volumetric strains suggest that in situ backfilled stopes simulated behave in a similar way to the fully-drained (FD) or the half-drained (HD) conditions. The MIP test results show that the pore structure varies between the top and the bottom of each column.

May 1, 2007

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011