Search Documents

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By WALTER VOIGTLANDER

FOR nearly 100 years wire rope has been fabricated in much the same way. To the great majority of mine superintendents wire rope is just wire rope, little or no semblance of individuality or identifying characteristics. Such an impression was fairly justified until three or four years ago when a practical means was found of performing or preshaping the wires and strands. This discovery permitted a revolutionary change in wire rope manufacture. Instead of merely twisting a number of wires into a strand, then twisting several strands into a complete rope (which twisting would naturally result in great internal strain, thus reducing the resiliency and over-all efficiency of the completed rope), the preformed wires and strands were laid in place without force or twisting. The obvious result was a rope more nearly approximating mechanical perfection. The applied loads are more evenly distributed throughout the component wires and strands, thus reducing unbalanced wire stresses. This results in a higher safety factor. The fact that preformed rope will not unravel when untied at the ends proves the absence of a torsional stress that exists in ordinary rope. A greater useful allowable stress in the wires is therefore possible in actual operating service.

Jan 1, 1926

By AIME AIME

WHEN H. I. Smith joined the Institute back in 1908, he was an instructor in mining and metallurgy at Penn State the college from which he had graduated the year before with a B.S. degree. He had not gone far afield for his education, for he was born, February 15, 1984 at Finleyville, Pa., a small village some fourteen miles south of Pittsburgh and without doubt famous chiefly as H. I.'s birthplace. The summer that he graduated he took a trip to the copper mines Arizona and Mexico and en route worked for four weeks for the Portland Gold Mining Co. at Cripple Creek, Colo., as a mucker and trammer. The next summer he roamed farther afield mines and metallurgical works in Europe. Wishing to see more of Arizona, he left the Penn State faculty early in 1909 and went out to Wenden in that State to become mining engineer and assistant superintendent of something called the Corona Copper Co., with 72 mining claims and a one-mule-powered whim for a hoist. When that job folded he helped build the Santa Fe railroad from Parker. Ariza., to Danby Cialif., and then came back to Pennsylvania to enter Government services as a junior mining engineer with the Bureau of Mines.

Jan 1, 1943

Jan 1, 1948

Jan 1, 1933

By William Campbell

FiRst I must express my deep appreciation for the honor of being privileged to give the Howe Memorial Lecture this year and at the same time my feeling of inadequacy to do justice to the subject. The first Howe lecturer was most fittingly, Professor Sauveur, his contemporary and friend, and the subject was beta iron. Last year the second Howe lecture was delivered by Dr. Mathews, one of his most distinguished pupils, who spoke on austenite. This year, the Howe Professor of Metallurgy was chosen to deliver the third annual lecture, and the subject ought to be martensite. No one but Professor Sauveur could have brought to life what was considered by many to have been dead and buried, and he so persuasively and convincingly proved to us by his experiments the existence of something that the followers of that new cult "X-Ray and Crystal Structure " would have us believe is simply alpha iron. And Dr. Mathews from his wide practical experience was so easily able to convince us that austenite was not only the most wonderful of the iron-carbon series, but that it was the wonder alloy of the future. If I were to follow in the footsteps of my distinguished predecessors, I would talk to you about martensite. But when I had planned this lecture, I found that I was writing about Professor Howe and his work and his influence on the science of metals of today, and that martensite had become the secondary theme. And when finally I was obliged to choose a title, I remembered that it was in 1901 I came from Roberts-Austen with a letter of introduction to his very dear friend, Henry Marion Howe, at the Columbia School of Mines, to continue my work at the next bench to Dr. Mathews. Since then a quarter of a century has gone by, and during that time all branches of science seem to have been remade, so great has been our advancement in knowledge and discovery. And now that Metallography has finally established its place as an important branch of science, with its own textbooks and literature, I would like to review what seem to me to be the most important advances we have made in the last 25 years. To do this, I would start with Howe's "Iron, Steel and Other Alloys," and end with Jeffries and Archer's " Science of Metals." In the preface of the former, Professor Howe wrote: My warmest thanks are due to the friends who have aided me with their counsel and knowledge. In particular, let me thank most sincerely Prof. Margaret E. Maltby

Jan 1, 1926

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By H. Clare Horwood

"Fractures and fracture zones containing veins and stringers of auriferous quartz in a quartz porphyry dyke are the principal structural features at the Howey and Hasaga gold mines. The 'break' containing the dyke was produced by a force from the northwest, the fractures in the dyke by compressive stress from the west.Both mines are in the north-central part of Heyson township, in the Red Lake area. They lie close to the southeastern side of the Dome granite stock. The Howey mine exhausted its ore reserves and ceased operations in November 1941. The Hasaga mine is producing at the present time (June, 1946).Mineralization was first discovered in the dyke in 1925 by the Howey brothers. Lorne Howey's discovery, which became the Howey mine, came into production in April, 1930; Ray Howey's find, which is now the Hasaga mine, started production in November, 1938.The total production from the Howey mine was 421,324 oz. gold and 144,253 oz. silver from 5,158,376 tons of ore hoisted ( 4,319,331 tons milled) during its 11 years of operation.The total production from the Hasaga mine from November, 1938, to December 31, 1945, was 124,434 oz. gold and 51,009 oz. silver from a total of 901,098 tons hoisted (721,361 tons milled).GENERAL GEOLOGYThe porphyry dyke containing the orebodies at the Howey and Hasaga mines lies a short distance southeast of the contact of a granite-granodiorite mass known as the Dome stock. The dyke fills a fracture trending N.65°E. in a tongue of Keewatin volcanic breccia that extends in a rather irregular manner into an elongate intrusive stock of dioritic rock known as the Howey diorite. The accompanying table presents the geological succession."

Jan 1, 1954

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By Egbert Burchardt

The challenge of "ore bodies getting steadily harder and lower in grade" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all. Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what "to do" and what "not to do". This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today?s experience and analyse its implications for existing and new operations.

Jan 1, 2012

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By Antti Roine

HSC Chemistry is a widely-used therniochemical tool in the chemical and metallurgical industries and in universities. The main reasons for it's popularity is the easy user interface and the large integrated thermochemical database. This paper summarizes the main properties of the new HSC Chemistry version 3.0, and gives a short review of the new features: Some metallurgical applications with the new features are also presented. HSC Chemistry 3:0 contains seven calculation modules and a thermochemical database with more than 11 ,000 chemical compounds. The new spreadsheet type table editor gives more control to the user, the new graphics routines have fewer limitations and more formatting properties. The capability and speed of calculation routines have also been improved.

Jan 1, 1998

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By S. Liaghat, J. Rosenkranz, P. Semsari Parapari, S. Chehreh Chelgani, A. Tohry

It is commonly accepted that the energy consumption for comminution within mineral processing is responsible for around 3% of the global electrical energy usage. However, it was clearly noted that inside mills, less than 1% of this energy efficiency is actually consumed for particle size reduction. Therefore, monitoring of grinding parameters and modelling of product particle size distribution (e.g. characterised by the 80% passing size P80) play an essential role in operating costs of a mineral processing plant. Several empirical models have been introduced for the prediction of the P80. Since in the industrial scale usually a few numbers of grinding variables are monitored, these models cannot identically be used in plants. In addition, these empirical models do not always indicate the magnitude of correlations between milling variables. This study proposes to introduce the Hilbert-Schmidt independence criterion (HSIC) as an intelligent model for exploring linear and nonlinear relationships between grinding variables and P80 for an industrial scale data assessment. HSIC can rank variables based on their importance and help to select the most effective one for the generation of predictive models. HSIC modelling through various monitored grinding variables (ball charge, feed input rate, F80, power draw and work index) of an industrial plant indicated that F80 as a feed property has the highest effect on P80 of the ball mill products. Modelling results highlighted that the P80 can be accurately predicted, based on effective variables by using a HSIC model. These outcomes showed that HSIC as a powerful modelling tool can assess the relationships between monitored grinding parameters, select the most effective grinding parameters and satisfactorily predict the P80. Keywords: Product particle size, variable importance measurement, Hilbert-Schmidt independence criterion, mill charge

Jan 1, 2020