Search Documents

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By Keith Rozenburg, Ivar Reimanis, Jesus Chapa

"Experiments in conjunction with finite element analysis (FEA) are used to better predict crack propagation in ductile/brittle graded composites. Cu/W graded composites were fabricated by stacking discrete layers of powders and hot pressing. Crack propagation was studied by loading a notched beam in four point bending and examining the subsequent crack deflection. The notch was placed within a particular composition of material, oriented in a direction perpendicular to the gradient direction. Elastic and plastic mismatch between different constituents in the graded composite induce shifts in the phase angle of loading, thereby causing the crack to deflect. FEA indicates that thermal residual stress has a negligible ""influence on the crack path. The combined FEA and experimental results suggest that elastic mismatch is the single most important material property-related factor in controlling crack deflection.IntroductionMany 'applications would benefit or may even require materials whose performance or functionality must vary spatially. While the concept of functionally graded materials has existed for nearly one hundred years, it is only within the last fifteen years, that research efforts have focused on generic issues in processing, properties and performance of functionally graded materials. This generic research effort has brought together scientists and engineers from traditionally different disciplines to address common issues with graded composites. The current work focuses on issues in structural joining. A wide variety of applications require some type of joining between dissimilar materials. Examples include thermal barrier coatings for turbine engines, wear resistant coatings for tools, ceramic engine parts, and microeiectronic devices, as well as many traditional applications involving metallic welding. The joints may either be discrete, involving a single interface, or they may· be spatially graded in composition. Extensive theoretical and experimental information exists on discrete bimaterial and trimaterial joints, but relatively little exists for graded joints or composites"

Jan 1, 2000

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989

By R. H. Thielemann

THE conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompany-ing failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installa-tions of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and tempera-tures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties.

Jan 1, 1939

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By Xiang (Frank) Chen, Mikhail A. Sokolov, Randy K. Nanstad

"Nickel-base Alloy 617 is being considered as a structural material for application in the secondary heat exchanger of the New Generation Nuclear Plant, a very high temperature gascooled reactor. Thermal aging of Alloy 617 plate and welds is being performed with tensile, Charpy impact, and fracture toughness tests conducted at temperatures to 950°C. Results of testing for thermal aging to 5,300 h have been obtained and are presented; varying effects of thermal aging temperature and time on fracture toughness are observed. The 9Cr-1MoV (Grade 91) ferritic steel is a candidate for structural applications in the sodium fast reactor. Fracture toughness testing of unaged Grade 91 steel has been performed to evaluate specimen size effects in preparation for future testing of the material in the thermally aged condition. Results for material in the mill-annealed and heat treated conditions are presented and show that this heat of Grade 91 steel does not indicate a small specimen bias on the fracture toughness Master Curve reference temperature.IntroductionThe behavior of advanced engineering materials will be a critical factor in the performance of Generation IV reactors. In the case of materials utilized for reactor internals and pressure vessels, the effects of irradiation and long time thermal aging are major issues. The environmental conditions for some of the Gen IV reactors are generally beyond present day reactor technology, requiring new experimental data as well as analytical predictions of expected behavior of candidate materials at conditions for which there are only sparse or no experimental data. The radiation environments and several key materials issues for some Gen IV systems are summarized in Section 5 of [l] as a starting point for modeling and microstructural analysis of Generation IV materials. More detailed descriptions of materials research and development needs and recommended activities for the SCWR, VHTR, and GFR are provided in references [2, 3, 4], respectively. Mansur, et. al. provide an interesting comparison of materials needs for Generation IV reactors to corresponding needs for fusion reactors and spallation neutron sources in [5]. The two primary candidate reactor systems currently undergoing significant research and development by the U.S. Department of Energy (DOE) are the New Generation Nuclear Plant"

Jan 1, 2012

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By Mahyera A, Sakashita B, Ahmed U, Abou-Sayed AS

Gas in U.S. coals is primarily composed of 90 to 99 percent methane and up to 10 per- cent carbon dioxide. In composition and heat- ing value, this coal-bed gas is similar to natural gas and can be introduced directly into commercial pipelines after standard condition- ing. The high permeability cleat system in the virgin coal can be exploited in order to drain the coal gas well in advance of mining. Two premining drainage methods have been extensive- ly evaluated in the U.S.; they are 1) horizon- tal boreholes collared from within the mine, and 2) vertical drilling from the surface with fracturing. Limited-size fracture treatments are advocated in order to prevent potential roof damage and the need for added support. An engineering approach to predicting gas flow for different drainage techniques near mining locations is presented. Results can be used in design, i.e. pipeline, compressor. Coal gas drainage from a horizontal borehole and a treated (contained fracture) vertical well for a 6 foot seam have been evaluated. Based on these results, it was concluded that selection of gas drainage techniques will depend primar

Jan 1, 1982