Search Documents

Jan 1, 1946

Jan 1, 1967

Jan 1, 1970

Jan 1, 1963

Jan 1, 1969

Jan 1, 1967

Jan 1, 1968

Jan 1, 1970

Jan 1, 1970

Jan 1, 1969

Jan 1, 1963

Jan 1, 1967

Jan 1, 1948

Jan 1, 1948

By PáDeáBosscher, A Bruwier, M Weidenbach, C Philippe, T Ly, A Van Den Bosch

In the mining business the cost of grinding media represents up to 40 per cent of the total milling cost and therefore grinding media optimisation has a direct impact on the concentratorsÆ bottom line. In the process of optimising grinding media alloys, Magotteaux developed its own methodology which consists of a series of analyses, tests, calculations and evaluations and assist the concentrator in optimising their processes.This paper presents the Prominent Hill case study where this methodology has been applied on both the secondary ball mill and regrind IsaMill«.The analysis of the wear conditions in the secondary ball mill allows Magotteaux to select a series of grinding media alloys to be tested to reduce grinding media consumption. By marking these different grinding media types with a unique drilling pattern, one can quantify the relative wear performance and cost effectiveness of each grinding media type within the same milling environment. After selecting the most economical grinding media composition a full scale industrial trial, involving topping up the selected grinding media is carried out and the media wear performance closely monitored and analysed.For stirred grinding mills, suppliers propose different grinding media, mainly ceramic beads, with specific properties and cost. Therefore the concentratorsÆ choice is a compromise between grinding efficiency, wear resistance and cost. The selection of the correct grinding media for stirred milling and the assessment procedure will be presented in this paper. The test results of the new stirred grinding media type in the regrind IsaMill« at Prominent Hill are presented and analysed.CITATION:Weidenbach, M, Van Den Bosch, A, Bruwier, A, Ly, T, De Bosscher, P and Philippe, C, 2012. Forging ahead - A collaboration between the OZ Minerals Prominent Hill Concentrator and Magotteaux to improve plant performance, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 105-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be “land poor” but “coastline rich,” meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. Within international waters, mineral wealth is the “Common Heritage of Mankind” with additional benefits for sponsoring states and their people.The Solwara 1 Project build continues with significant progress over the last twelve months. The Seafloor Production Tools (SPTs), Subsea Slurry Lift Pump, riser pipe, launch and recovery systems and winches are now complete with delivery to test facilities and the vessel ongoing. Recent focus has been on submerged trials for the SPTs, but the vessel build continues to progress to schedule. Nautilus appreciates the great support thus far from our all our stakeholders.Our focus is to develop the world's first commercial high grade seafloor copper-gold project in an environmentally and socially responsible manner and to launch the deepwater seafloor resource production industry.Nautilus’s marine research continues, including a 3.5-month series of exploration cruises for Seafloor Massive Sulphides in the Bismarck Sea, as well as fabrication of purpose designed exploration equipment."

Jan 1, 2017

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn't any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn't any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992