Search Documents

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov, D. V. Magazanik

Based on theoretical and experimental researches of phosphate and carbonate minerals flotation in the presence of soluable glass at various pH values and sodium silicate concentrations, it has been established that the presence of soluble glass in solution leads to formation of silicate compounds on the surface of phosphate and carbonate minerals causing change in their floatability for the worse. The harmful influence of soluable salts is done by tying of collector as metallic soaps, forming precipitates on the surface of minerals to be floated and causing their depression of flotation, and breaching of the froth etc. Depressing action of slimes and products of interaction with collector depends on the ratio of values and signs of potentials of the mineral surfaces. The possibility of phosphate and gangue minerals separation can be evaluated by comparing the minimum-necessary concentrations of collector required for their flotation.

Jan 1, 2002

By Frew J. A, Harris M. C, Manlapig E. V

The recovery achieved in a flotation process is a function of both the characteristics of the feed stream and the operating conditions within the flotation cell. In this paper, the flotation characteristics of the streams within the Red Dog le

Jan 1, 1997

By R. S. Wang

The flotation of pyrite which be pretreated by electrochemical ways under external controlled voltages in different pH is explored. The floatability of pyrite is increased indistinctively after being pretreated in acidic and xanthate environment; Whereas, it is increased obviously between 400~800 millivolt in alkaline and xanthate condition. The reason for higher recovery of pyrite is that oxida-tion reaction, which results in S0 and S02, takes place on its surface, and that ethyl xanthate is oxi-dized into dixanthogen. In the meantime, the kinetics and mechanism is also studied.

Jan 1, 2014

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

Although mining, particularly of gold and coal, played a significant role in the development of New Zealand, from the time of the spectacular gold rushes of the 1860s its economic importance to the country as a whole has decreased substantially since that time. Gold, coal and non-metallic agricultural and industrial minerals have been found in economically significant quantities, however, the search for base metals has not been successful.

Jan 1, 1982

By Max Kraut

UNTIL VERY RECENTLY the flotation process has not found much application in the treatment of gold ores. No appreciable improvement has been made lately in the technology of this application; but the possibilities of flotation have been more fully appreciated. Excellent results were obtained long ago, but few operators paid much attention to them. For instance, in 1915 extensive experiments were carried out by Mr. Beauchamp and Minerals Separation on ores from the Dutch-Sweeney mine near Jimtown, Calif. The ore contained gold-bearing pyrite and laboratory tests indicated a 10c. tailing on a $6 head. In 1918 a 300-ton flotation mill using Minerals Separation machines was built based on the results obtained. However, when the mill began full-scale operation, mill heads did not come up to expectation, being only $4; also the-tonnage was considerably less than had been expected. Flotation mill tailing assayed 15c., indicating a recovery of over 96 per cent, so that excellent metallurgical results were obtained. The operation was a success but the patient died.

Jan 1, 1932

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979