Search Documents

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By Leon D. Keller

Fine screening, as discussed in this paper, pertains to the use of the Rapifine DSM Screen to make a 65 to 325-mesh separation at production tonnages. The greatest number of Rapifine Screen installations are in magnetic taconite plants where the unusual relationship between the grinding mill, cyclone classifier, magnetic separators, and fine screens makes the Rapifine Screen application unique. Since the initial fine screening installation on magnetite in 1961, (1) additional installations and further testwork have contributed to the fund of information which is the basis of this paper. The addition of fine screens to the grinding-classifying circuit of a magnetic taconite plant creates a change that effects all components of the circuit. Pine screens in a non-magnetic plant have also been investigated, but here the benefits have not&apos; been as clearly defined. Screens classify according to the particle size. Hydrocyclones classify by a combination of particle size and particle weight. The change in the type of classification minimizes overgrinding of the mineral. The resultant savings in grinding power can be used to increase the throughput, upgrade the product, or increase recovery.

Jan 1, 1971

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By Robert B. Parsons

"The tax reform process marches on. The December 16, 1987 measures tabled by Finance Minister Michael Wilson represent one more step toward the objective of total reform of Canada&apos;s income and sales taxes. While the income tax changes are taking shape, much work still needs to be done on the sales tax side of the coin.IntroductionOn December 16, 1987 Finance Minister Michael Wilson tabled measures to implement the changes to Canada&apos;s income tax system that were proposed in the June 18, 1987 White Paper on Tax Reform. The measures were set out in a Notice of Ways and Means Motion; draft legislation relating to preferred shares, research and development expenditures; and draft regulations regarding capital cost allowance, certified films, flow-through shares, and the resource sector. The reaction of the government to the recommendations made by the Finance and Economic Affairs Committee Report on Tax Reform (the Blenkarn Committee), the Report of the Standing Senate Committee on Banking, Trade and Commerce and through consultations with interested groups and organizations, business, labour and individual Canadians is set out in a booklet of supplementary information.The basic features of the reformed income tax system set out in the White Paper remain. However, a number of significant changes have been incorporated in the Notice of Ways and Means Motion and other material. The following comments address those area s where changes have been made to the original White Paper proposals."

Jan 1, 1988

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By W. L. Remick

THE hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past 2 years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co., Pottsville, Pa. This plant is now operating. APPLICATION The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from %2 in. down to and including "dust." (Anthracite passing a 32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes. from 3/8 in. down to "dust. 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and _washing. processes which may be considered outside the realm of coal cleaning. PRINCIPLE OF OPERATION Fig. 1 shows the method of classification practised under the Hydrotator patent:1 In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical &apos;equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

By M. I. Novgorodova

Most of the gold in the earth&apos;s crust occurs as finely-dispersed gold and accounts for much of the gold lost in extraction processes and during exploration for gold. The Compositions, sizes, and morphology of fine gold particles (0.01 to 10 ~m in diameter) were studied with high resolution electron microscopy coupled with electron microprobe and microdiffraction devices, using colloidal carbon replicas. Correlations were made between fine gold, mineral associations and ore genesis. The results provide qualitative information on the proportions of finely dispersed, invisible and visible gold distribution in ores. Such knowledge is fundamental when planning an optimum technological recovery process.

Jan 1, 1991

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

By Shibu John

Rising energy demand and steadily decreasing quality of raw materials due to the global resource depletion are great challenges to the steel production today. The FINEX® Process has been developed jointly by POSCO, Korea and PRIMETALS Technologies Austria, to provide the iron making sector with the capability to lower hot metal production costs, environmental pollutions and to increase the flexibility in terms of operation and the choice of raw materials. FINEX® is a new technology combining a gas-based reduction in a series of fluidized bed reactors and a reduction smelting in a melter gasifier. Commenced in April 2007, the first 1.5Mtpa commercial plant has demonstrated the competiveness as an alternative iron making route. Another 2.0 Mtpa, third generation FINEX® (3G) plant was recently installed at POSCO, Pohang Works and has been operating satisfactorily since its blow-in in January 2014. Based on the well-proven plant concept, new process features, the highly competitive production costs and environmental advantages, the FINEX® Process can be considered as a competitive alternative to the conventional blast furnace iron making route.

Aug 17, 2017

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

By Ron Stewart, Richard Youmaran, Andy Adler

In the current context of heightened concerns with explosives security, there is significant interest in technological controls to improve security. It is important to be able to control what is fired, by whom, where and when. This paper describes research Orica has performed to investigate and test biometric systems to address the question of "by whom". The goal of this research is to incorporate the most suitable biometric system onto the 'blaster' unit of an electronic initiation system. This approach will ensure that only authorized personnel can initiate a blast involving electronic detonators. Requirements analysis: we initially explored many different biometric technologies to evaluate them against the requirements, including security, usability, ruggedness, size, form factor, privacy, and operational temperature range, This analysis identified chip based fingerprint sensors as the best candidate. Development of prototype units: in order to test the identified sensors, we modified standard, commercially-available, electronic blast initiation units ("blaster") to incorporate a fingerprint reader. Testing and evaluation: Biometric We conducted a biometric scenario evaluation in order to determine: 1) security level (measured by false accept rate (FAR)); 2) usability (measured by failure to enroll (FTE) and false reject rates (FRR)), and to 3) discover environment specific issues and challenges (such as temperature, humidity, dirt, or those related to the usage patterns of the user group). Tests were conducted at quarry sites in eastern Ontario, Canada. Results show rates of: FAR= 0%, FTE= 1.67%, FRR= 28.81%. Overall, these results suggest that this fingerprint biometric technology has a good level of usability in this application of electronic blast initiation control.

Jan 1, 2007

By C Bonini, A Markham, P Whittle, B Pearson

"Mine-derived sedimentation in rivers can have significant impacts on the processes and features of the receiving environment and impact on communities reliant on this environment. However, identifying and quantifying the contribution of mine-derived sediment to the receiving environment can be complex. This is particularly the case in remote environments and where little/no baseline assessments have been undertaken. One approach that can be used involves sediment fingerprinting, whereby a unique tracer is identified within the mine-derived sediment to discriminate between mine- and non-mine derived sediment sources downstream. The technique typically involves sampling of sediment at upstream, control and impact sites and sites within the mine deposit. Laboratory analyses are run on all the samples to determine whether the chemical signature (eg presence/concentration of specific metals) differs between each group of samples. In complex environments where the mine-derived signature may be difficult to detect from a basic review of the data, or where sampling constraints may limit the number of samples for analyses, statistical methods can be used to help identify sediment groups. This paper provides a mine case study to show how such an assessment can be undertaken despite the logistical challenges faced while working in remote environments.CITATION:Pearson, B, Markham, A, Bonini, C and Whittle, P, 2013. Fingerprinting and signatures - tracing mine impacts in complex aquatic systems, in Proceedings Water in Mining 2013, pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013