Search Documents

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By Harri J. Lehto, Marja I. Oja

"The purpose of grinding circuits is to produce a particle size distribution that has as much as possible the wanted particle size class. In practise, however, the production of the wanted size class is not at all as simple as it sounds. In the case of industrial minerals for example the end user may give very tight specifications for the particle size distribution and for the chemical composition of the product. This leads in many cases to a very demanding grinding process, if we want to reach and maintain these specifications. In other words, the required size distribution is not necessary the best possible for the chemical composition.Screen models aim to predict the size distribution and flow of the products when a feed size distribution, feed tonnage, and grade efficiency curve are known. The approach used in this study was to select the most suitable empirical model for classification. Suitability of the existing models has been evaluated and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model.The performance of a screen was evaluated in order to minimize the amount of fine material in the screen overflow. The experiments were carried out using Derrick single-deck screen, first alone with recycling and then in the closed circuit with a rod mill using two different scales. The separate screen tests showed the expected behaviour of the grade efficiency curves. In the pilot tests the Leonard screen efficiencies stayed almost constant. This suggests that the screen works better in a milling circuit. However the loading of the screen turned the product of the mill coarser that helped screening. The grade efficiencies obtained from the pilot tests had the same general shape. The regression analysis of the pilot test runs did not give an acceptable correlation for the parameters. This suggests that pilot tests cannot be directly used to scale or to optimise industrial milling circuits. However they can be used to predict the trends of behaviour of an industrial circuit."

Jan 1, 2003

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998

By A. N. Lazaridi, S. I. Afanasenko, S. A. Safonov

"This scientific work presents the results of comparative tests of centrifugal concentrators with a vertical and horizontal axis of rotor spinning. The article also describes a qualitative analysis of the behavior of mineral particles in a centrifugal field with fluidization for concentrators with a horizontal axis. The analysis was aimed at studying the effect of the quantity of fluidization holes in the basket on the degree of magnetite recovery and the effect of the basket rotation speed. The experiment demonstrated that concentrators with a horizontal axis are not inferior in terms of the qualitative recovery indicators to concentrators with a vertical axis. The researches also provided facts about the wide practical application of concentrators with a horizontal rotor arrangement. INTRODUCTION Methods of gravity concentration, attractive for their ecological purity, see their revival. First of all, this is due to the invention of centrifugal concentrators with the fluidization of the layer of mineral particles. The creation of a new generation of gravitational centrifugal concentrators made it possible to achieve a tangible breakthrough toward the direction of reducing the grain size of mineral particles effectively divided by density, up to 10 µm at a high production capacity of the vessels reaching 500-600 tons per hour. Such separators enable dressing a crushed ore of flotation grade and in some cases replace the flotation process, especially in primary operations, in joint cycles. In the long term, this method of concentration should significantly expand the scope of application, replace partial flotation processing, ensure the introduction of environmentally friendly energy-saving technologies at ore-processing plants. Summarizing the international experience for the last 30 years, it can be confidently asserted that centrifugal methods of concentration have become widely used in processing schemes for the separation of finely dispersed products in the mining industry. An interest in the creation of installations using centrifugal acceleration for the separation of mineral particles by density has particularly grown. Dozens of centrifugal concentrator designs have been created and continue to be improved. Centrifugal concentrators have a number of obvious advantages, which are especially relevant today. Losses of fine gold during the process of mining are well known. Gold washers screw, spiral separators, jigging machines and sluices traditionally used in the production processes do not solve the problem of fine gold recovery. Table 1 shows the results of comparative tests of a centrifugal concentrator (ITOMAK) and other concentration equipment. According to the research conducted by the company GMRS, Krugersdorp, South Africa (2000), the initial material was gold ore crushed to 150 micrometers (90%)."

Jan 1, 2018

By Glaser. C., J. Balz, F. Logsch, R. Heiduschke, M. Leiker, P. Ay

The treatment of iron-hydroxide-containing water from ground water and surface water is achieved by a combination of the process steps of flocculation and subsequent mechanical dewatering. The aim is to create solid pellet structures by extending the structure forming flocculation process with a build-up pelletizing process which can be transferred directly into a drying unit. A Taylor-Couette-reactor (diameter of the inner cylinder – 40 mm, gap width – 5 mm) was used for these experimental studies. To produce the necessary flow profile the inner cylinder was rotated at a speed of 230 rpm. The iron hydroxide-containing suspension (dry matter content: 2 mass %) was added simultaneously with the addition of a cationic high-molecular flocculant in various flocculant dosages and residence times of 5 to 15 min. The pellets were examined for parameters such as geometric dimensions, dry substance content and dewatering behaviour. As the results show, there is a direct relationship between the residence time and the geometric dimensions of the pellets. After a residence time of 5 min, round pellets with an average diameter of 6 mm were formed. With an increase in the residence time up to 15 min, a compaction of the pellets could be observed, which resulted in an increase in the dry substance content of 8.0 to 11.2 mass % on average. After completion of the pelletizing process, the pellets were mechanically dewatered by filtration. By applying this innovative wet pelletizing of iron-hydroxide containing suspensions in a Taylor-Couette-reactor, it is possible to carry out the process of flocculation combined with the pellet formation with simultaneous pellet compaction in a single process step. The resulting pellet structures are distinguished from conventional floc structures by an improved water discharge capacity. After classification the pellets can be marked directly as easy-to-handle bulk material, suitable as feedstock in percolation columns for the purification of contaminated fluid streams

Jan 1, 2018

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.