Search Documents

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By F. C. Harris, S. J. Gaab, J. Sattarvand, S. Duzgun

Underground mines are inherently dangerous due to potential hazards such as fires, explosions, and caving of rock. Although these events are rare, once they occur a speedy and safe egress of mineworkers is critical to survival. Static evacuation systems use exit signs or directional lines but can get obstructed or be hardly visible in smoky or dusty conditions. This paper presents the investigation of the effectiveness of a smart evacuation technology in underground mining, where a real-time guidance system leads individuals on an optimised path to the egress while avoiding danger zones, compared to conventional practices. Participants simulated an evacuation from a virtual reality mine, using the conventional system and the smart evacuation system with real-time guidance. The highest reduction in evacuation time using the smart method amounted to nearly 40% on average. Moreover, 83% of participants preferred the smart guidance system, and agreed that it could enhance safety.

Sep 1, 2021

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

The purpose of this paper is to demonstrate how the Computational Fluid Dynamics (CFD) technique can be an attractive approach to evaluate the performance of face ventilation systems. To present the capability of the CFD for such a study and for design purposes, a series of simulations using CFD have been performed at the Department of Mining Engineering, University of Kentucky, for different face ventilation arrangements (e.g. different scrubber geometries, brattice (curtain) and continuous miners locations, airflow quantities, etc.). Results from these simulations are displayed as three dimensional graphs and discussed. Needs for the field validation of these results and refinements of design methodologies are also discussed.

Jan 1, 1998

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Zvi Rivlin

Classical nucleation theory states that in first order phase transformations, such as liquid to solid transition, nucleation of the product phase starts with the formation of small, unstable clusters (embryos). When the thermodynamic barrier to nucleation is overcome, the embryos grow and attain a critical size, beyond which they are stable, i.e. they become nuclei. If nucle- ation does not occur, the parent, liquid phase remains in metastable equilibrium. At temperature lowers, undercooling increase and atomic mobility decreases. The viscosity change in the undercooled liquid may result in the formation of glassy state. As demonstrated in previous papers [I-21, in solidification involving surface nucleation of the product phase, as the case is in rapid quenching by melt-spinning, both nucleation temperature and nucleation time depend upon the number of atoms available at the isothermal surface in contact with the substrate. As a result of the thinness of the melt-spun ribbons, the embryo clusters that form at the freezing temperature may not be supplied by the amount of atoms necessary for their growth to critical nuclei sizes. In such extreme conditions, the liquid does not crystallize, it forms a metallic glass. A numerical simulation method is proposed for the reactions involved in embryo cluster formation and growth, at the atomic level. The simulation enables the caIcuIation of either the nucleation or the glass transition temperatures. Calculations made for the well-known glass forming CuZr and FeB systems afford prediction of the geometrical and thermodynamically conditions necessary for the formation of either crystalline or amorphous ribbons in melt-spun ribbons.

Jan 1, 1994

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By A. Rejeb, A. Millard

ABSTRACT: An evaluation of the importance of the thermo-hydro-mechanical couplings (THM) on the performance assessment of a deep underground storage design has been made as part of the international DECOVALEX III project. It is a numerical study that simulates a generic repository configuration in the near field in a granite medium. The thermo-hydro-mechanical evolution of the whole configuration is simulated over a period of 100 years. The model used to represent the unsaturated behaviour of the various porous media makes allowance for moisture transfers through the effect of thermal and water gradients. The paper presents a comparison of the temperature, water pressure and stress fields obtained by TM, TH, HM and THM coupled calculations. The results demonstrate that temperature is hardly affected by the couplings. In contrast the influence of the couplings on the mechanical stresses is considerable. This is attributed to the key role that water has on bentonite swelling or shrinkage effects that are dependent on its saturation level variations. KEY WORDS: Modelling, thermo-hydro-mechanical couplings, temperature, pressure, stress. ZUSAMMENFASSUNG : Im Rahmen des internationalen Projekts DECOVALEX III wurde untersucht, wie groß der Einfluss thermisch-hydraulisch-mechanischer Kopplungen (THM) auf die Leistungsfähigkeit eines Konzeptes zur Lagerung hoch radioaktiver Abfälle zu bewerten ist. Bei dieser numerischen Behandlung wird eine generelle Lagerungskonfiguration in granitartigem Milieu simuliert. Die thermisch-hydraulisch-mechanischen Prozesse werden für eine Dauer von 100 Jahren simuliert. Bei dem Modell, mit dem das Verhalten der verschiedenen, unterschiedlich porösen Milieus in ungesättigtem Zustand dargestellt werden soll, werden die Feuchtigkeitstransporte infolge thermischer und hydraulischer Vorgänge berücksichtigt. Verglichen werden in diesem Artikel verschiedene Temperatur-, Wasserdruck- und Beanspruchungsfelder, die sich aus TM-, TH-, HM- und THM gekoppelten Berechnungen ergaben. Dabei stellte sich heraus, dass die Temperatur nur gering von den Kopplungen berührt wird. Die Einflüsse der Kopplungen auf die Mechanik sind hingegen bedeutend; ausschlaggebend dafür ist der Faktor Wasser, der den Bentonit je nach Sättigungsgrad quellen oder trocknen lässt. SCHLÜSSELWÖRTER: Modellbildung, thermisch-hydraulisch-mechanische Kopplungen, Temperatur, Druck, Beanspruchung. RESUME : Dans le cadre du projet international DECOVALEX III, une évaluation de l’importance des couplages thermo-hydro-mécaniques (THM) sur les performances d’un concept de stockage de déchets fortement radioactifs a été menée. Il s’agit d’une étude numérique simulant une configuration générique de stockage en champ proche dans un milieu granitique. L’évolution thermo-hydro-mécanique de l’ensemble est simulée sur une période de 100 ans. Le modèle utilisé pour représenter le comportement non saturé des différents milieux poreux prend en compte les transferts d’humidité sous l’effet de gradients thermiques et hydriques. L'article présente une comparaison des champs de température, de pression d’eau et de contraintes obtenues par des calculs couplés TM, TH, HM et THM. Les résultats montrent que la température est peu affectée par les couplages. En revanche, l’incidence des couplages sur la mécanique est importante; ce qui est attribué au rôle majeur joué par l’eau à travers les effets de gonflement ou de retrait de la bentonite selon la variation de son degré de saturation. MOTS-CLEFS : modélisation, couplages thermo-hydro-mécanique, température, pression, contrainte.

Jan 1, 2003

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By Giulio Antunes de Medeiros, Leonardo Martins Silva, Giselle de Mattos Araújo, Rayla de Souza Caldas

To analyze the direct reduction of self-reducting briquettes producted with different electric arc furnace dust contents, three sets of homogeneous mixtures were produced with elephant grass biomass, iron ore, cement and furnace dust in increasing levels, which were submitted to thermogravimetric tests in muffle furnace and TGA furnace at variable temperatures and times. The curves of degree of reduction were obtained and the reduced briquettes were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the reducibility of the agglomerates is diminished by the increase of furnace dust, with variations of this result at higher temperatures. The observed microstructures were spherical particles, porous structure or whiskers. Based on XRD results, it was considered probable that the decrease of the degree of reduction with the increase of furnace dust content is related to the reaction between hematite and zincite, which is expected to be controlled by zinc diffusion.

Oct 1, 2019

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By Ronald M. Tipton

Freeze and thaw deterioration is a serious problem In con¬crete pavements. The main cause of distress Is thought to be the pore structure of coarse aggregate. In an attempt to characterize deleterious pores, the Iowa Pore Index test and the Expected Durability Factor, as Calculated from the mer¬cury intrusion porosimeter, were devised. This study Included freeze-thaw and sodium and magnesium sulfate soundness testing of sixteen carbonate aggregate samples. In addition, the Iowa Pore Index and the Expected Durability factor were determined for each of the samples. All of the Above mentioned physicochemical parameters were examined using bivriate correlation analysis with the In¬tent to evaluate the effectiveness of the Iowa Pore Index and Expected Durability factor for predicting the frost dur¬ability of an aggregate. The results from the bivariate correlation analysis showed no significant correlation, between the Iowa Pore In¬dex And- Expected Durability factor with the other physico¬chemical parameters investigated. Rust interesting is that the Iowa Pore index predicted that All of the tested samples would resist freeze-thaw failure, whereas the Expected Durability factor predicted that -ash sample would he non-durable.

Jan 1, 1987

Evaluation of the Iron Blast Furnace Process using Heat and Material Balances of the Flame-Zone

Sep 13, 2010