Search Documents

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By Zehong Wang

Selecting sodium polyacrylate (PAAS) as grinding aid, the effect of grinding aid on the grinding efficiency of bauxite taken from Shanxi province was studied and its mechanisms were analyzed by measuring the variation of adsorption characteristic, pulp viscosity, surface electric potential of the bauxite and the surface appearance of particles. The results showed that, compared with no grinding aids added the content of -0.074mm in the ground product was increased by 5.45 percentage points under the optimal grinding conditions adding PAAS as grinding aid when the amount of PAAS was 0.7%wt of bauxite. Because the physical adsorption and chemical adsorption were occurred on the bauxite surface, which could reduce the pulp viscosity, change the surface electric potential of the bauxite, enhance the surface appearance of particles and lower the surface hardness of the bauxite, the grinding efficiency of bauxite was increased by PAAS. Keywords: bauxite, grinding aids, grinding efficiency, mechanism

Sep 1, 2012

By G P. W Suyantara, Y Tanaka, T Hirajima, Y Aoki, K Sasaki, H Miki

The effect of sodium sulfite (Na2SO3) on the flotation behaviour of bornite and tennantite is reported in this work. Flotation tests were performed using pure minerals of bornite and tennantite under various concentrations of sodium sulfite at pH 9. The flotation results indicated that sodium sulfite exhibited a depressing effect on the floatability of bornite in the presence of 0.1 mM PAX. However, tennantite remained floatable after the addition of sodium sulfite in the presence of 0.1 mM PAX. The flotation tests using mixed bornite and tennantite confirmed the flotation results of single minerals. Surface characterisation using X-ray photoelectron spectroscopy (XPS) was performed to explain the flotation results. A mechanism is proposed based on the XPS analysis results.

Aug 24, 2022

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By Larry M. Southwick

Extraction of gold and other metals from ores suspended in liquid slurries often involves gases (such as oxygen) as a participant in the reaction. An important factor then in setting the rate of extraction can be mass transfer of the gas into the liquid and/or solids. A number of recent studies have indicated that as solids loadings increase, mass transfer rates of gas into solid-liquid mixtures decreases. This would seem to imply that lower solids loadings would be beneficial to increased reaction rates. However, since it is the solids which are being reacted, a most intriguing paradox is created. More solids should lead to more surface area to react, but it seemingly also provides less gas to react. So is the reaction faster or slower as solids loadings increases? The creation of this paradox is imbedded in how mass transfer and reaction data is collected and measured, how it is analyzed and correlated, and finally on the rate controlling steps in the reaction. An alternative analysis of these studies is presented which clarifies and eliminates the paradox. The analysis applies to water slurries as used in gold or other metal leaching processes or in bio-hydrometallurgy, as well as to molten metal/solid/gas mixtures such as might be encountered in submerged gas injection.

Jan 1, 1999

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By Ma F, Yang Q, Ujihira M

The effect of stresses and acoustic emissions on the gas permeability of coal was investigated in the field and the laboratory in order to find an estimative method of the practicability of gas drainage. In the field, acoustic emissions and gas emissions during gas drainage drilling were monitored tentatively at some coal mines in Japan and China.In the laboratory, acoustic emissions from coal specimens in addition to gas permeability were measured during the triaxial compression loading in order to interpret the results monitored in the field. Besides, the opening of gas permeation channels in coal was considered on the basis of the experimental results.

Jan 1, 1991

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005