Search Documents

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009

By G. Van Weert, A. van Sandwijk, O. W. J. S. Rutten

"Cathodic and anodic reactions in an acidic nitrate medium were studied in reference to the production of electrolytic manganese dioxide from pyrolusite' (Mn02) ores by reductive leaching. Two USA ores were investigated. The reductant for the pyrolusite ore is produced cathodically in an electrolytic cell and can either be nitrous acid (HN02) or nitric oxide gas (NO). In this work emphasis was placed on the nitrous acid leach. In a high-temperature leach in a nitrous/nitric acid medium, manganese and silver are solubilized and iron is not. Anodic electrowinning of manganese dioxide from the acidic manganese nitrate electrolyte yields flaky y-Mn02, similar to that produced from sulfate and chloride electrolytes. Cathodic regeneration of nitrorts acid was studied in a membrane cell in 1.0 M nitric acid and 0.0 to 0.1 M nitrous acid on a' platinized titanium cathode. At cathode potentials ranging from +950 to +700 mV (SHE), cathodic reduction to nitrous acid takes place, at cathode potentials < +700 mV, cathodic reduction of nitrous acid to nitric oxide takes place. A conceptual process is presented and discussed.IntroductionManganiferous-silver oresLarge reserves of manganiferous-silver ores are present in the Southwestern United States and Latin America. These ores are generally refractory to hydrometallurgical methods of treatment, due to the insolubility of the higher oxides of manganese (Mn 4+) in all common lixiviants such as cyanide solutions, dilute sulfuric acid, nitric acid, ammonia, salt solution, thiosulfates, etc. The silver is either bound by the insoluble manganese, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization.Higher oxides of manganese will dissolve if they are first reduced pyrometallurgically to manganous oxide (Mn2+). This is a widely used pretreatment for manganese dioxide ores and subsequent dissolution in sulfuric acid is common. In order to avoid the pyrometallurgical pretreatment with its large energy requirements and gaseous emissions, fully hydrometallurgical processes have been proposed. These processes are based on the presence of a reductant in solution, in order to reduce the insoluble higher oxides of manganese to soluble lower oxides. Aqueous S02 has been proposed and tested on industrial scale by the U.S. Bureau of Mines. After washing, silver could be extracted by cyanidation. The neutralization of the pulp prior to cyanidation however causes problems in filtration and the reagent consumptions are high [1]. More recently, acidified thiourea and bacteria were proposed for the solubilization of both manganese and silver in a single leach step. High extractions were obtained, but drawbacks of these methods are high reagent consumption or slow kinetics [2,3]. For the options of manganese recovery from the leach filtrate, precipitation with persulfate or ammonium carbonate and ion exchange have been proposed. The proposed options for silver reclaim are precipitation with either zinc or Na2S and adsorption onto activated carbon."

Jan 1, 1997

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By Satu Strömberg

A single-particle laminar-flow technique was used to study oxidation of two nickel concentrates and a granulated nickel matte (43 wt% of Ni). Experimental conditions were: reaction gas from N2 to N2 + 75 vol% O2; gas preheating temperatures ranging from 500 to 1100°C. The major nickel-bearing minerals in the two concentrates were pentlandite and violarite, respectively. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology and mineralogy. Total desulfurization of the nickel concentrates was achieved under the most oxidizing conditions, while the sulfur removal from the nickel matte was not as efficient, especially with the coarse size fraction. Pentlandite-based concentrate was found to be less reactive than the violarite-based.

Jan 1, 1995

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By Heikki K. Jalkanen

Thermodynamic properties of copper-iron mattes and slag-matte distribution of copper and some minor matte constituents (Ni, Co, Mo, As, Sb and Bi) are discussed on? the basis of equilibrium measurements: a change from. oxidic to sulfidic solubility as the predominant form of dissolution of copper takes place as matte grade decreases. Distribution coefficients of minor matte constituents are complex functions of sulfur and/or oxygen potentials?. The distribution behaviour of different? metals can be qualitatively derived from their affinities to copper and stabilities. of their sulfides and oxides. The equilibrium results are compared with commercially observed values. from Outokumpu.Oy flash smelting furnace.

Jan 1, 1983

By Z. R. Llanos

This paper presents a review of industrial and experimental processes for the recovery of molybdenum, vanadium, nickel, cobalt and aluminum from spent hydrotreating or hydrodesulfurization catalysts. Numerous processes have been developed in a laboratory and pilot scale. However, worldwide, there are only four well established commercial facilities currently in operation. The installed capacity of these facilities exceeds the availability of spent catalysts and may be sufficient to assimilate future increases of spent catalysts. Despite liability risks; significant quantities of spent catalysts are still being landfilled. Changing regulations that may affect the future handling and disposal of spent catalysts are also reviewed.

Jan 1, 1995

By Jr. Langhans, J. S. McPartland

"The presence of zinc in cyanide solutions is generally thought to not have an adverse effect on precious metal recovery or recovery rate by heap leach processing. However, analytical interferences of zinc in solution can cause problems in accurately determining and controlling cyanide concentration in the leach solution, leading to increased cyanide consumption. Analytical methods and the chemistry of cyanide in the presence of zinc are reviewed. The effects of solution pH and zinc concentration on the free cyanide determination were evaluated in detail. Use of the standard silver nitrate titration and a modified titration method for controlling cyanide concentration during heap leaching were investigated experimentally. The practical implications of cyanide heap leaching in the presence of cyanide soluble zinc minerals are discussed.IntroductionThe presence of zinc in precious metal cyanidation circuits is not uncommon. Zinc can be introduced into cyanide leach solutions through dissolution of various zinc minerals1>, or through the use of a Merrill Crowe (zinc precipitation) circuit. Zinc minerals typically occur infrequently and in low concentration in gold ores, but are more abundant in silver ores. Merrill Crowe systems are most commonly employed for recovery of precious metals from solution for relatively high silver ores. It is desirable to control the amount of dissolved zinc in a cyanidation circuit for several reasons. Excessive zinc build-up in cyanide leach solution can, under certain circumstances, inhibit precious metal dissolution and adversely affect solution recovery systems. Additionally, high zinc concentrations can lead to excessive in-process cyanide inventories and potentially, to higher cyanide consumption"

Jan 1, 1999

By A. Kiziltas, D. J. Gardner, C. W. Mcllwraith, J. W. Bridge, M. L. Peterson

"Dynamic mechanical thermal analysis (DMTA) tests were conducted on high-oil content, paraffin-based wax used in wax-coated granular composites. These composites make up the surface of synthetic Thoroughbred horse racetracks used in North America. The modulus and damping response from the DMTA tests were correlated with the dynamic triaxial shear strength response of the bulk track material taken at two different operational temperatures and at four strain rates. The purpose of these tests is to understand the mechanisms of shear strengthening of the bulk track material as the wax is heated through the first crystalline solid to liquid nominal transition temperature. Previous work using differential scanning calorimetry confirmed that under common operational surface temperatures, the wax coatings undergo distinct thermal transitions. The resulting increase in triaxial shear strength values affects the consistency of the racetrack which, in turn, can potentially affect Thoroughbred racing performance and safety of the track surface.IntroductionSynthetic granular composite materials are being used in nine Thoroughbred horse racetracks in the United States as well as in other tracks around the world. In one case, their use was mandated by the state of California in 2007 due to testimony that these tracks were significantly safer than traditional dirt tracks [1]. Several synthetic tracks have shown substantial reductions in injuries since switching to synthetics; one California track showed a 75% reduction in catastrophic horse injuries during the first year as compared to the previous year racing on a dirt track [2]. The composition of the tracks in the U.S. generally consist of silica sand (>70%), polymer fibers (<5%), and rubber particles (0-15%) all coated with a paraffin-based, high oil content wax [3, 4]. In a recent study of several synthetic racetracks, to include the track location in this study, the oil content ranged from 34 to over 44% by mass [5]."

Jan 1, 2011

By Dinesh Agrawal

Microwave energy has been in use for variety of applications for over 50 years. These applications include communication, food processing, wood drying, rubber vulcanization, medical therapy, polymers, etc. In the last two decades microwave heating has been also applied very effectively and efficiently to heat and sinter ceramic materials. Microwave heating is recognized for its various advantages, such as: time and energy saving, very rapid heating rates, considerably reduced processing cycle time and temperature, fine microstructures and improved mechanical properties, better product performance, etc. The most recent application of microwaves has been in the field of metallic materials for sintering, brazing/joining and melting. Several common steel compositions, pure metals and refractory metals have been sintered in microwaves to nearly full density with improved mechanical properties. Many commercial powder-metal components of various alloy compositions including iron and steel, copper, aluminum, nickel, Mo, Co, Ti, W, Sn, etc., and their alloys have also been sintered in microwaves producing better properties than their conventional counterparts by using a 2.45 GHz multimode microwave system. This work has been further extended to join and braze bulk metal pieces, especially super alloy based turbine blades. Further, in a specially designed microwave cavity, even the bulk metals can be made to couple with the microwave field and melted. The implications of these findings are obvious in the field of powder metal technology.

Jan 1, 2006

By Do-Hyeong Kim, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

"Thermodynamic relations among Mn, Al and N in liquid iron were studied by measuring the effect of Mn on the solubility product of AlN in liquid Fe-Mn-Al-N alloys in the temperature range from 1773 to 1873 K. The critical Al and N contents for AlN formation were determined by the metal-nitride-gas equilibration technique over wide ranges of melt composition and temperature. The effects of Mn on N solubility in Fe-Mn and Fe-Mn-Al melts containing Mn up to 26 mass% were separately determined in the same temperature range. The experimental results were thermodynamically analyzed using the Wagner's formalism to estimate the critical Al and N contents for the onset of A1N formation. The validity was checked by the observation of inclusion evolution in Fe-20%Mn-1.5%Al-0.6%C-0.3%Si-0.012%N melt during cooling and solidification.IntroductionRecently, high manganese steels such as Twinning Induced Plasticity (TWIP) steels have been developed as next generation steels because of their high formability as well as excellent strength and ductility.[1•2l In these steel grades, a large amount of Mn (15-20 mass%) and Al (1-2 mass%) are added to liquid steels, and such high Mn and Al concentration bring the great challenges to the steelmaking and casting processes. Mn significantly increases the N solubility in liquid iron and the AlN inclusions can be easily formed at such high Al concentrations due to high affinity of Al and Mn with N in liquid steels. Although the AlN inclusion is known to be a dominating and considered as a detrimental phase for the hot ductility of steels,l3l thermodynamics of AlN formation in high Mn-Al alloyed liquid steels was not well known.Moreover, the melting point of these steels decreases down to near 1623 K as increasing Mn content up to 20 mass%. However, most of thermodynamic data has been measured at the steelmaking temperature around 1873 K. Even at steelmaking temperature, there are huge scatters in thermodynamic interactions of Mn and Al on N in liquid iron. The nitrogen solubility in Fe-Mn alloy melts has been measured using the Sieverts' method[4l and the samplinij method[5-7J in the temperature range of 1813 to 1973 K. In the authors' recent study,[8•9 the N solubility in Fe-Al alloy melts was measured using the sampling method in the temperature range of 1823 to 1973 K. However, the simultaneous effect of Mn and Al at high concentrations on Nin liquid Fe-Mn-Al-N alloys is still not known. Also, there remains uncertainty about the temperature dependence of the interaction parameter of Mn on N in liquid Fe-Mn alloys. Therefore, it is worthwhile to check the temperature dependence of this parameter at a low temperature near the melting point of Fe-Mn alloys. There have been few studies on the characterization of non-metallic"

Jan 1, 2014

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Ryszard Prajsnar

During copper production in shaft and flash smelting processes at KGHM Polska Miedz S.A., lead bearing material of sulfide, sulfate, and oxide character is generated in forms such as slime from shaft furnace gas handling systems, converter dusts, and dusts from an electric furnace for copper removal from flash smelting slag. These materials are polymetallic concentrates of Pb, Zn, and Cu, with As, Cl, and Cd as impurities. Shaft furnace slime, containing. about 50% PbS and 15% bituminous substances, is the main lead-bearing material. At the Glogów copper mill, a new plant was commissioned in June 2001 to process 80,000 tonnes per year of lead bearing materials to produce 26,000 tonnes per year of crude lead. The plant consists of a feed conditioning system, three (3) rotary rocking furnaces with a capacity of sixteen (16) tonnes of lead feed fired with natural gas and oxygen-enriched air containing up to 45 vol% O2, and a gas handling system. The gas handling system includes a post-combustion chamber, a gas cooling chamber with Cl neutralization, gas mixing chamber, bag filter, and dry limestone scrubbing system for SO2 removal. The lead-bearing feed is smelted with five (5) wt% Na2CO3 and thirteen (13) wt% iron scrap at a temperature of 950 to 1050°C for three (3) hours. The smelting process consists of four (4) stages; feed drying, firing of gaseous hydrocarbons and solid coal from the feed, lead reduction from slag, and separation of molten products. The flow rates of natural gas and oxygen to the burners are controlled to ensure combustion of the bituminous material in the furnace. The process produces crude lead bullion containing (wt%) 0.1 to 0.5% Cu, 0.02 to 0.5% As, 0.05 to 0.07% Bi, 0.1 to 0.5% Sb, and 0.1 to 0.6%Sn. The process also produces a mixture of sodium silicate slag, Fe-Zn-Pb-Cu-S matte, and Fe-As speiss containing (wt%) 5 to 10% Pb, 2 to 6% Cu, 10 to 15% Zn, 1 to 3% As, 10 to 15% S, 0.5 to 3.0% Cl, 2 to 4% K, 4 to 7% Na, 20 to 30% Fe, and 5 to 10% SiO2. The dust is made up of PbO, ZnO, PbSO4, and PbCI2, KCI, and NaCI with a chemical composition (wt%) of 35 to 50% Pb, 5 to 15% Zn, 3 to 6% As, 4 to 8% Cl, 2 to 5% K, and 2 to 5% Na. The construction of the new lead production plant at the Glogów copper mill will process both current lead-bearing materials as well as lead-bearing material that have been stockpiled over the last fifteen (15) years to give a significant improvement in protection of the natural environment.

Jan 1, 2002

By Zhendong Tao, Wei Huang, Zhongxi Yang, Hang Guo, Haoran Geng, Jingxiang Yao

"CaSO3.0.5H2O typed Flue Gas Desulfurization (FGD) gypsum is a by-product formed in flue gas desulfuration by double-cycle fluid bed method, its composition is different remarkably from that of gypsum yield by normal desulfuration methods, and few studies using it as cement retarder have been carried out. In this paper, the experimental study using CaSO3•0.5H2O typed FGD gypsum as cement retarder was carried out. The experimental results indicate that, when FGD gypsum is added solely into cement, the retarding action is not satisfactory because of its slow dissolution rate; The composite retarder composed of FGD gypsum and natural gypsum can regulate efficiently setting time of cement over a wide range of addition and rate of both each other, and the mechanical property of cement can be improved significantly.Fire-power plants have discharged a lot of harmful gases such as SO2 etc., which has resulted in serious pollution on the environment. To reduce harmful gas containing sulfur in the flue gas, various flue gas desulfuration (FGD) techniques have been developed. At present, the FGD method used widely is to add desulfuration agents such as limestone powder or other calcareous-contained materials during the coal burning or in the flue gas so that the components containing sulfur react with them to form solid sulfate or sulfite and to be separated from the flue gas by collectors. CaSO3•0.5H2O and CaSO4•2H2O typed FGDgypsum can be obtained respectively by dry and wet FGD process[1,2]. As a by-product of fire-power plant, features of of FGD gypsum and its applications have been paid great attention. Pavel Tesa'rek et al [3] presented in full the characters and properties of FGD gypsum; Zofia Konik et al[4] prepared expansive additive used to cemnent industry by using FGD gypsum and aluminate clinker; A. K. Alva et al [5] investigated the effects of FGD gypsum and fly ash on soil properties and found the growth of seedlings of either rootstock improved significantly in soils amended with FGD gypsum and fly ash. FGD gypsum also can be used in gypsum binders, plasters and plasterboard manufacture [2.6]. C. S. Poon et al [7] investigated the effects of FGD sludge on the pozzolanic reaction of reject-fly-ash-blended cement pastes. Many studies using CaSO4•2H2O typed FGD gypsum as cement retarder has been reported[2,8-12]. Howevere, few studies using FGDG as retarder were reported so far. In present study, the chemical compositon, phase composition, structure and features of CaSO3•0.5H2O typed FGD gypsum have been analyzed, and its application characters used as cement retarder have been investigated experimentally."

Jan 1, 2008