Search Documents

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By Reza Ghomashchi

Casting is the most economical route to transfer raw materials into readily usable components. The economics of casting would be more pronounced and better realized, if there are no or limited necessary post fabrication treatments. Therefore, there is an urge towards near or net-shaped casting as there are significant advantages over conventional casting including reduction of component weight, excellent surface finish, higher strength and integrity of the as-cast parts, closer tolerance, and the ability to produce pore-free parts by controlling the solidification shrinkage. The concept of near or net-shaped casting is currently employed for both semi-finished products such as strip-casting and finished shaped casting, as in case of high pressure die casting or squeeze casting. The full potential of this process yet to be explored and is expected to be realized within the next 10 years, especially in case of strip casting. The current article discusses different near or net-shaped casting routes currently employed for fabrication of high integrity finished products with main emphasis on aluminum-silicon alloys. In this regard, attempts will be made to identify the key parameters during fabrication and highlight the importance of process control and optimization in fabricating premium quality cast products. Keywords: Near Net Shape casting, Solidification, die casting, squeeze casting, rheocasting, thixocasting

Jan 1, 2003

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Jewel Andrew Gomes

Arsenic is considered as one of the toxic materials being controlled by Environmental Protection Agencies in several developed and developing countries. It is found in the nature as constituents of the soil, minerals and also in various organic forms. It enters the air, water, and land from wind-blown dust and gets into water from runoff, leaching, soil erosion and anthropogenically from chemicals used for wood preservation, insecticides, medicine, military purpose, pigments, and electronic circuitries. There are several techniques available for removal of Arsenic, such as coagulation/filtration, lime softening, ion exchange, reverse osmosis, nanofiltration, wet chemical, and electrochemical. Electrocoagulation has been found as one of the most efficient techniques to remove inorganic arsenic with more than 99% efficiency. In this paper, we present our work on electrochemical treatment of both the inorganic and organic arsenic from water using various sacrificial electrode materials, i.e., iron, aluminum, copper, and combination of them. The floc produced by this method has been also characterized using XRD, SEM/EDS, FTIR, and cyclic voltammetry.

Jan 1, 2010

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009