Search Documents

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Chris T. Franke

The Waste Isolation Pilot Plant is a deep underground facility mined in bedded salt interspersed with persistent clay inter- beds. The clay seams delineate beams of salt above and below the excavations which strongly influence excavation performance. This paper reviews available rock mechanics information relevant to improving drift stability by removing the roof beam. Conceptual deformation mechanisms, relevant field data, and numerical analyses were used to investigate the effects of mining the roof of the excavations along a clay seam. Finally, a case study that applies the results of this investigation is presented.

Jan 1, 1997

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By Khaled Morsy

Longwall mining is one of the most widely practiced underground coal mining method. The behavior of the longwall gob is very critical in the understanding of the complex ground response to longwall mining. In the limited data available, the values of gob moduli used in numerical modeling ranged from 1,000 psi to over 300,000 psi. Such a wide variation in moduli would greatly affect the results of the numerical analysis. A better understanding of the behavior of the gob will allow numerical models to be more accurate for simulating longwall mining conditions. In this study, a gob model based on the Terzaghi's model was incorporated into the comprehensive finite element package, ABAQUS, to simulate the loading behavior of longwali gob material. A case study was used to verify the proposed gob model.

Jan 1, 2002

By Chris Strawson

Moranbah North is a modern longwall operation mining premium coking coal in the Northern Bowen Basin, Central Queensland. Australia Moranbah North Coal (MNC) is owned and operated by Anglo Coal Australia. Extracting approximately 4.5m of the Goonyella Middle seam using a single longwall, the mine produces 5 to 6 Mt per annum. The weak coal (4.5 MPa), low strength laminated immediate roof, and strong upper roof sandstones, make operation of the longwall at depths in excess of 250m geotechnically challenging. In the past, there have been a number of production delays due to geotechnical issues. Roof instability resulted in a long stoppage on Longwall 105, and the eventual relocation of the face further outbye in the block. (Figure 1). When mining commenced in LW106, there was a requirement for uninterrupted production, particularly in the more demanding inbye area of the panel. Following discussions with a number of Geotechnical experts, it was decided to narrow the face, and test the theories of reduced face weighting due to spanning of the goaf across the panel. A new on line chock monitoring system, and microseismic monitoring was installed in order to characterise the difference in the rockmass response, as the panel width changed from 175m, to 265m, and then 300m. The nature of the goaf formation and impacts on face loading and production are discussed, having the unique opportunity of three different face widths within the same area.

Jan 1, 2007

By James Pile

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan's geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro¬active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

Jan 1, 2003

By R. Fritschen

In order to investigate locations, source parameters, and source mechanisms of mining induced seismic events, a local network of seismic stations was installed at a coal mine in the eastern part of the Ruhr District (Germany). The recorded events were located with the help of an anisotropic velocity model, which accounts for the fine layering of the carboniferous strata. Most of the events took place about 50 m above the working Luise 76-10. Their locations correlated with the advancing working face, and the number of events increased when pillar edges were undercut. The source mechanism, i.e., the orientation of the fracture plane and the direction of displacement on this plane, could be determined for several seismic events. The majority of them was characterized by a fracture plane parallel to the working face and an almost vertical dislocation on this plane towards the goaf a mechanism resembling the breaking down of the hanging wall. The fracture plane had a dimension of about 100 m. Probably the fracturing of a sandstone layer, located approximately 40 m above seam Luise, was responsible for the observed seismicity

Jan 1, 1999

By Stephen P. Signer

A field test was conducted by the U.S. Bureau of Mines at the Cyprus Plateau Starpoint No. 2 Mine. near Price. UT. to study the support rock interaction mechanics. Twelve instrumented. fully grouted roof holts and eight sagmeters were installed in the roadway of a two-entry gate road to measure load changes and roof movements. Readings were taken during section development and as each longwall panel passed the test area. Loads that resulted from development of the en- tries were higher than would be expected if simple suspension of the roof rock was the sole cause of loading. When the first longwall face passed the test section massive beam behavior was exhibited over the entry and adjacent pillar. However, no significant localized bending was detected at any of the strain gauge locations. After the first panel passed the test section. all the roof bolts had at least one zone where the steel had yielded. Loading continued to increase. and when the face from the second panel was adjacent to the test section. 70 pct of the strain gauges at the 6-. 1%. and 30-in locations had passed the yield point of the steel roof bolt. However, even at these high load levels, the supporting pattern was sufficient to provide adequate reinforcement to the mine roof.

Jan 1, 1990

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Wolfgang Schott

The propagation velocity of in-seam seismic (ISS ) waves depends on frequency which is also known as dispersion. This dispersion is not only determined by the thickness of the coal seam and its dirt hand content (i.e. thickness and position), but also by the rock type and its condition (soft or compact) above and below the coal. A coal panel completely surrounded by roadways was investigated using the in-seam seismic transmission survey technique. Along the roadways the immediate roof was either sandstone and shale- The seam thickness varied between 1.20 m (sandstone in the roof) and 1.40 m (shale in the roof) and a fault system (normal faults) crossed the panel with a total throw of about the seam thickness. Below this coal seam another coal scam with a thickness of about 80 cm exists. Its interval shown by exploratory drilling changes from about 60 cm to more than 6 m (scam splitting). Tomographic inversion was applied to the dispersion of the measured ISS waves and velocity distributions were calculated at frequencies found to he most sensitive to changes in the seam thickness and the distance to the coal seam below. By correlating the velocity distributions with known values along the roadways approximate distributions of the coal seam thickness and the seam splitting within the panel were produced. The mining of the coal panel had already been finished and comparison was made between the survey results and the actual situation as far as it was documented. Prediction by the seismic survey was partly in good agreement with the actual held conditions or showed at least the same trends.

Jan 1, 2003

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Michael Karmis

During the last 25 years, technological advancement and subsidence research have resulted in more accurate and diverse prediction capabilities. The work presented in this paper focuses on the development of integrated prediction capabilities for dynamic deformation indices and for strains over sloping terrain. In order to assist subsidence engineers with accurate prediction methodologies, the research also addresses the development and validation of techniques that can enable model calibration using alternative measured subsidence parameters such as horizontal or ground strain instead of the traditional vertical subsidence values. This paper presents the basic concepts and validation of the above mentioned enhanced prediction and control methodologies, which are necessary for effective assessment and control of mining-induced subsidence, using examples and case studies. In addition, a risk assessment approach for evaluating landscape stability over mined areas is presented. The enhanced prediction methodologies have been incorporated into the Surface Deformation Prediction Software (SDPS) package.

Jan 1, 2008

Design and selection of support systems for longwall faces call for in-depth knowledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state-of-the-art datalogger system. The mechanised longwall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 K W DERD shearer. The datalogger system was capable of storing data simultaneously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build-up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Russell C. Frith

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings arc based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations. Results from the study illustrate periodic weighting cycles of varying severity and these are related to the overlying geology in terms of the strength of individual strata units, their thickness and proximity to the longwall extraction. Several different caving mechanisms are identified which contribute to periodic weighting cycles. The importance of recognising weighting cycles in relation to the operation of the longwall face will be discussed in detail. Longwall support design methods are critically examined in relation to the case histories of the monitoring program. The applicability of the said design methods to Australian coal mining conditions is discussed and an outline of design considerations to facilitate productive longwalling is presented. Overall, the paper only "scratches the surface" of the work currently being undertaken by ACIRL in this area, and the findings of that work.

Jan 1, 1992

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004