Search Documents

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-expanding push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source found in the USA is bastnaesite, a rare earth bearing fluorocarbonate mineral, currently mined at the Mountain Pass Mine in California. To increase production, it is essential to optimize existing processes and create new ones to better utilize current resources. Therefore, a US Department of Energy Critical Materials Institute sponsored research program was carried out at the Kroll Institute for Extractive Metallurgy to expand the fundamental understanding of the industrial bastnaesite concentrate leaching system. With the help of prior knowledge, thermodynamic calculations and design of experimentation based lab testing, a novel single-stage hydrochloric leach system was created to optimize the rare earth extraction from bastnaesite. Historically, the existing industrial process has utilized a two-stage leach system involving a high-temperature hydrochloric acid leach with liquid solid separations followed by a caustic crack stage of the leach residues. A series of single-stage leach experiments were run by reacting locked cycle flotation concentrates with hydrochloric acid to test common leaching parameters. The results of these patent pending single-stage tests have shown rare earth recoveries significantly higher than reported recoveries of historic two-stage caustic crack processes, all while decreasing the equipment required and the type and amount of reagents needed.

Jan 31, 2022

By Robert E. Murray

The title of my paper, "A Company's Response to Federal Coal Leasing," brings to mind a picture of a dog chasing its tail. This is what the coal industry, has been doing since the Federal coal leasing moratorium went into effect in 1971. We've gone around in many circles, but we are only very slowly, if at all, getting closer to catching our tails, i.e., efficient, economical, and rational Federal coal leasing. My companies, The North American Coal Corporation and its four Subsidiaries, The Falkirk and Western Plains Mining Companies and The Coteau and Missouri Valley Properties Companies, together hold in excess of 4.5 billion tons of lignite reserves in North Dakota. Some of our North Dakota properties are substantially interspersed with Federal coal, with the government holding title to the minerals in every other section. This checkerboard pattern of Federal ownership has made it difficult to develop and market some of our reserves, and, as a result, it has become imperative that we be familiar with and active in the Federal Coal Leasing Program.

Jan 1, 1982

By Raymond S. Shrode

Transportation is one of several important increments in the total market cost of most commodities. On a national average it has been reported that transportation accounts for about 25% of the total cost of a product at the market place. And industrial minerals are no exception. In fact, the proportionate cost frequently exceeds the 25% average. Further, it may actually determine the economic value of a deposit. Transportation may possibly be thought of as a specialized subject of concern only to a traffic manager and of only nominal interest to the mining engineer, the geologist or other technically oriented member of mineral producers' staff. However, in the industrial minerals field, interest is not commonly confined to exploration, development, production or marketing, but is in contrast an overlapping one. In a very real sense this broad area of interest in the total economics of the business is the specialty of the industrial minerals man. And transportation is a vital part of the total picture. Comments in this paper deal with rail transportation.

Jan 1, 1969

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By David Wright, Jerome Chamfray, Anthony Harding, Brian Boye

Conway’s Law states that unless we intentionally design automation tools around what we need, we will simply replicate our existing processes. While we may achieve some savings this way, there is an opportunity for greater benefits if we re-imagine the way we, as an industry, perform design. This paper examines current technology and shows how even small departures from merely encoding what we currently do could reap significant benefits. From these examples a framework is developed for a new and innovative approach tvo automation that will allow us to design more quickly, to a higher quality, and communicate outcomes more effectively.

Dec 1, 2022

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By M. A. Trevits, G. W. Luxbacher, L. D. Patts

"It is almost a given that post-disaster mine conditions will have compromised the mine ventilation system, resulting in a hazardous atmosphere in portions of the mine, and often complicated travel through debris fields and roof falls. Robotic technologies provide the opportunity to gather valuable information to assist decision making or lessen exposure to dangerous conditions. MSHA's Mine Emergency Operations Division (MEO) has utilized a fully permissible mine robot, the V2, for a number of years, constantly updating the unit as new technologies became available. The National Institute for Occupational Safety and Health, as part of the MINER Act Extramural Contract Program, examined the need for additional robotic units and ultimately funded three different types of prototype technologies: two robots, the Snake Robot and the Gemini-Scout, and a mine rescue robotic assist vehicle known as the ""Mule"". The Snake Robot is designed to be lowered through a borehole and to conduct surveillance (gas monitoring, video and audio) in the immediate vicinity, while the Gemini-Scout, designed to be deployed in the mine opening, serves as a more mobile and agile exploratory tool as compared to the MSHA V2 robot. The Mule was developed in response to needs expressed by mine rescue teams for a versatile remotely operated support vehicle and it will move from prototype to MEO utilization in the near future. This paper describes the development of the robot prototypes and discusses their limitations in the prototype stage, possible enhancements and potential applications, as well as the utilization of the Mule. INTRODUCTION The conditions in a coal mine may be dramatically altered after a mine fire or explosion. For example, the ventilation system may not be functioning correctly as control devices may be compromised or damaged beyond repair. The visibility in the mine opening may be limited due to accumulated smoke and dust. Roof support systems may be damaged or no longer functional. Equipment and materials may be strewn about the mine opening. Debris fields, blocked openings, roof falls, flooded areas, gas accumulations and active burning make it very difficult or impossible for those managing the post-event emergency to permit mine rescue teams to enter the mine to conduct search and rescue operations. With the evolution of robots and robotic assist technology there has been a proliferation of purpose-built units for the military, police and law enforcement agencies, urban search and rescue and those contending with hazardous environmental conditions. In each case, the technology used is designed to limit human exposure to the unsafe conditions or to provide access to areas under difficult conditions. For example, a specially-designed marine robot has been deployed into the damaged core of the Japan’s Fukushima Daiichi Nuclear Power Plant to assess the conditions of the containment vessels, where melted fuel is believed to have accumulated. Human access to the area is prohibited due to dangerously elevated levels of radioactivity [1]. Multiple robots were deployed in Amatrice, Italy, to assist in the response after the 6.2-magnitude earthquake devastated the town. The robots were used to explore two medieval churches that were severely damaged and deemed too dangerous for human entry [2]. Tactical robots are regularly used by police and law enforcement agencies when the conditions of the emergency place intervening officers directly in harm's way [3]."

Jan 1, 2018

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By David Mast, Amanda Foote, Mina Shinouda

The Michigan DOT’s I‑75 Modernization Project, Segment 3, is a 30-year, $1.2 Billion design-build-finance-maintain project in Southeast Michigan. The scope includes building a nearly 4-mile long, 14.5-foot ID stormwater storage tunnel. The tunnel and pump station are being built concurrent with new roads and bridges, requiring multiple levels of design and construction coordination. Underground risks include the poten‑ tial for encountering granular soils, groundwater, and explosive gases. The new tunnel will be mined by a new open-face TBM and lined with a one-pass steel-fiber-reinforced precast concrete segmental lining. Shaft construction began in early 2020 and tunnel mining in July 2020.

Jun 13, 2021

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By G. F. Weaton

1.1 The purpose of this paper is to show the way by which estimates are made of the tonnage and grade of iron ore and taconite reserves of Minnesota. 1.2 The procedures include those of estimating the open pit reserves of: (a) Natural iron ore, and (b) Taconite 1.3 The methods of estimation which will be discussed are primarily based on the information from exploring iron ore deposits. They consider the geology of the deposit as well as the contained mineral of potential value. 2.0 Some geologic, engineering, and economic principles. 2.1 Ore 2.11 "In the broad economic sense, and from a legal standpoint as well, ore is mineralized rock, which under appropriate conditions of time, space, technology, economics, and politics, can be mined, processed, and made to yield a saleable metal , or other mineral products at a profit."(Parks, 1957) Stated differently, metallic ore is rock material from which presently known methods of beneficiation, a merchantable concentrate, suitable for use in the manufacture of metals at a profit, can be produced. Crude ores as low as 0.38% metal, as in the case of copper and even lower in the case of the precious metals.

Jan 1, 1985

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By Steve Kral

The mining industry has waited a long time for the resurgence in commodity prices and demand for its products that it is now experiencing. Base and precious metals prices have reached levels not seen before. Coal prices have also shot up. And there are encouraging signs in the uranium market. China’s nearly out-of-control economic growth is said to be the leading driver for much of this resurgence. But demand for energy, metals and building materials in the United States and elsewhere are also major factors. The result is that expansions and new mines for nearly every commodity are in the works.

Jan 1, 2005