Search Documents

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By B. Andersen

An accurate knowledge of Interactions among mineral particles and between such particles and dissolved and precipitated species Is Important in developing efficient separation processes. In this investigation interactions in Florida phosphatic clay waste, that are relevant to dispersion and selective reagent adsorption, the two main prerequisites for selective flocculation, were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slime were due to unselective polyacryllc acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Ai and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. Further increase in separation of natural slime is likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1992

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By E. Pizarro

Division Andina has considered in its long range planning, the exploitation by panel caving method of "Third Panel" mine, which was started its production stage during the second half of 1995. This mine has two production levels, the first is grizzly level and another is L.H.D. level. Both sectors use the same haulage level where mineral is recollected through ore pass. For mineral loading and haulage its use 50ton diesel trucks combined with electro-hydraulic chutes. The automation has permitted what this operation is carrying out with remote control by driver's truck, in concordance to short range planning.

Jan 1, 1998

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

The removal of tritium from tritiated water (-0.5 µCiIL) was studied by metallothermic reduction using aluminum. The influence of the three variables namely the aluminum powder amount, the NaOH concentration and the reaction time has been studied on the tritium activity reduction. The experimental results and statistical analysis showed that more than 85% of tritium can be removed from the tritiated water. Further work on the tritium recovery as well as efforts to totally decontaminate water by incorporating a cryogenic concept is currently pursued.

Jan 1, 1998

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self-advancing hydraulic supports. U.S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology has greatly increased productivity. Past trends are used to predict future technological directions.

Jan 1, 1997

By J. T. Clancey

The potential inadequacy of natural gas reserves to supply projected requirements in the 1980's has been pointed out.(1,2) As a result, interest has arisen in the development of new, potentially low-cost processes for the conversion of coal into high BTU gas. In June, 1964, the office of Coal Research (U. S. Department of interior) and Consolidation Coal Company (now a subsidiary of Continental Oil Company) entered into a contract to continue work on coal gasification utilizing the Consol CO2 Acceptor Process. Work under this contract has been specifically directed toward the use of lignite as the carbonaceous feed, although the process is also applicable to non-caking subbituminous coals. The primary objective of this work was to establish the technical feasibility in continuous bench-scale equipment, of the novel features of the C02 Acceptor Process. Secondary objectives were the testing of commercially obtainable acceptors and the design and economic evaluation of a commercial facility. The bench-scale process development has been completed successfully and the construction of a large pilot plant at Rapid City, South Dakota, has been authorized. It is the purpose of this paper to review the technology of this new gasification process and to present the current projected economics of a plant producing 250 MM SCFD of pipeline quality gas.

Jan 1, 1969

By R. Day

Nahcolite is a naturally occurring sodium bicarbonate mineral found principally in the Piceance Creek Basin of northwest Colorado. An 8-m thick nahcolite bed, 610 m below the surface, is the target of this first commercial nahcolite mine. A chamber and pillar mining system is developed by solution mining parallel 8-m tall by 18-m wide by 450-m cavities initiated along horizontally drilled holes. Hot water leaching, cooling crystallization and flash drying is the process. The sodium bicarbonate product is consumed by the baking, animal feed, industrial and acid rain abatement markets. A project overview, emphasizing the combination of horizontal drilling and solution mining technologies, will be presented.

Jan 1, 1994

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010