Search Documents

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By K. Rajamani

The word adapt means "to change so that one's behavior will conform to new or changed circumstances." Applying this definition to process controllers suggests that an adaptive controller can change its behavior in response to changes in the dynamics and disturbances of the process. In the minerals industry there are many control cases where adaptive control will provide superior control as compared with more traditional PID (proportional, integral, derivative) control. A typical plant uses as many as 100 to 200 control loops for lprocess regulation. Therefore, the task of initially tuning and then periodically retuning these controllers is a formidable problem, During the time the controllers are "un-tuned", product quality may deteriorate and unstable operations may result. Adaptive controllers are capable of tuning themselves, thus avoiding this problem. The computers commonly used in distributed control systems are easily capable of implementing adaptive controllers. In addition to the possibility of using the control computer to implement adaptive controllers, many distributed control systems will offer adaptive control as a standard feature in the near future.

Jan 1, 1984

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By Y. Numata

2-Mercaptobenzothiazole (MBT) is a heterocyclic-mercaptan and belongs to a group of molecules containing nitrogen and sulfur as electron donor atoms. MBT has been employed as a collector in flotation under names of MBT, Captax, and Flotagen. It is a major constituent of reagents in the 400 series of the American Cyanamid Co. Current applications of the reagent include flotation of copper minerals, tarnished or oxidized lead, copper activated sphalerite, and nickel ores. It has been used successfully in the flotation of pyrite in acid circuits in the range of 4 to 5.

Jan 1, 1990

By M. A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970's, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the O.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6,560 Mm Id (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2,832 m Id (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm Id (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1993

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985

By H. C. Harrell

The Tennessee Valley Authority began employing geophysical well logging for foundation investigations in October 1973. Since that time more than 3,000 holes have been evaluated for engineering purposes. The Tennessee Valley Authority has not actively used geo-physical well logging for exploration of construction materials, but we feel that much of the information derived from geophysical logs for foundation exploration is applicable to the construction materials industry. This paper will then discuss geophysical logging as applied to foundation engineering and, by implication, the feasibility of use in construction materials exploration. The use of geophysical logging and percussion drilling instead of coring has greatly expanded TVA's data acquisition capabilities and has also resulted in substantial savings in time and money. Economical boreholes are obtained through the use of large percussion track drills (Figure 1). This equipment is capable of drilling through the overburden, setting steel casing on the top of rock, and drilling the rock beneath the casing. Holes as deep as 400 feet (121.9 m) have been drilled by this method.

Jan 1, 1977

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998