Search Documents

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015

Operation of a pilot-scale Floatex density separator was studied using a pyrite concentrate slurry feed. Experimental measurements were further utilized in parameterization of a hindered settling simulation model. The model incorporates particle slip velocity calculation and also a separation efficiency function, adjusted to describe the feed material characteristics. The model was used to compute the overflow and underflow compositions when both fluidization bed pressure and teeter water flow rates were varied. In addition, prediction accuracy and the model validity were evaluated. The simulations gave good results when the teeter interstitial velocities were moderate enough to avoid excessive turbulence in the fluidization. Prediction of the cumulative overflow and underflow size distributions in most experiments yielded essentially less than 10% relative error between the sample data and the estimated value of the 50% passing sizes.

Jan 1, 2011

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By R. J. Watters

Many rock sass classification systems exist' to assist the engineer in assessing the rock support requirements for underground design. Our ongoing research in this area is directed at attempting to utilize the fractal dimension and the acoustic emission' response of the tuffs at Yucca Mountain, Nevada to further aid in rock mass classification. The Topopah Spring' member, the proposed nuclear waste horizon, is characterized by welded and partly welded tuffs, exhibiting a wide range in moduli, strength, porosity and degree of fracturing. Differentiating between the different' types of porosity can be extremely difficult if not impossible. An attempt was made to correlate the acoustic emission response with the porosity of the sample. Events and the peak amplitude may offer a means-to distinguish between, fracture porosity and pore porosity. In addition-, fractal dimension were calculated for several fractures in densely welded tuffs. Two techniques for calculating fractal dimension were-applied' to describe-fracture geometry and roughness. Fractures in-welded-tuff were-found to be relatively smooth.

Jan 1, 1989

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By Niles E. Grosvenor

Several methods have been proposed for determining the tensile strength of rock. These have been tried out over the past several years, but the results have been erratic and of doubtful value. The tensile strength of rock is its weakest property, and this property apparently enters into all failure phenomena whether underground or on the slope of an open pit. Therefore, it is essential that detailed quantitative information is known about the tensile strength of rock if the design engineer is going to select the proper pit' slope, pit orientation, or orientation of underground workings so as to give the most economical and safest mining condition. This quantitative information may be used to orient the pit in such a manner as to allow steep slopes along two sides. This information may possibly be used to orient the direction of either underground workings or open pits so as to decrease powder consumption and to increase blasting efficiency. Hence it is of prime importance that a method of determining accurately the tensile strength of rocks be developed.

Jan 1, 1960

By T. Kretschmer, F. Villwock

Conveyor systems are an essential part of many material movements in all conceivable areas of application. They are used to transport goods in raw materials extraction, agriculture, and even articles for daily use. In the process, not only distances of several kilometers but also differences in altitude of several hundred meters are bridged. The layout of the conveyor usually follows the topography at the respective installation site. Particularly in the case of large height differences, safety devices must be provided to prevent uncontrolled movement. Backstops can take over this task in predominantly ascending overland conveyors and are used either as a primary or as a secondary safety system in conjunction with a service brake. They are always used when the system comes to an unplanned standstill, whether due to a power failure, an emergency stop or a defect. When designing backstops, it must be ensured in any case that all conceivable circumstances are taken into account so that failure is ruled out without the product being unnecessarily large in size. Various safety factors are applied, some of which are even prescribed by authorities. One example is the Australian standard on machine safety for bulk material belt conveyors (AS/NZS 4024). This stipulates a redundant acceleration safety device that can absorb at least 150% of the maximum load. ALTRA Industrial Motion with its sister companies Marland and Stieber manufacture backstops for a wide range of applications. With more than 85 years of business activity in freewheeling and backstop applications, they are among the most known and experienced companies and provide a great know-how.

Mar 2, 2022