Search Documents

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By Ehsan Alavi, Glen Frank, Michael DiPonio, Mike Mooney, Lisa Mori

"A study was conducted on the N125 project in Seattle to investigate the use of apparent density as an assessment tool for the effectiveness of soil conditioning. The formation of an air bubble as well as the plugging of cutterhead and excavation chamber can be a result of improper soil conditioning. Both air bubble formation at the top of the excavation chamber and developing plugging issues can be identified by analyzing the apparent densities in the excavation chamber. In this study, apparent densities less than unity were observed in the upper portion of both northbound and southbound TBMs, suggesting the presence of an air bubble. Apparent densities greater than the in-situ soil density were observed in the lower portion of the excavation chamber. Particularly high values of apparent density were coincident with clogging observed at multiple locations along the alignment. The combination of less than unity upper chamber apparent density and very high apparent density in the lower portion of the chamber are related, and indicate the inability of the TBM to effectively condition and mix the soil in the chamber.INTRODUCTIONProper soil conditioning in EPB tunneling offers many advantages to the quality and productivity of the project. There are few operational parameters that can be used to assess the soil conditioning performance such as advance rate, torque, thrust, chamber pressure signature, etc. One of the other parameters that potentially can be used is the apparent density. The apparent density of the material in the chamber was introduced by Guglielmetti et al. (2003) as the vertical chamber pressure gradient calculated from the physical relation between the horizontally measured chamber pressures and the vertical distance between the pressure sensors. Guglielmetti et al. (2003) introduced apparent density as a measure to ensure the excavation chamber is filled with material. To guarantee face stability the authors suggest to keep the apparent density over a certain limit so the material is able to transfer effective stress to the virgin soil, and thus provide support of the excavation face. They implemented this method at the Metro project in Porto, Portugal.Comparing the vertical gradient of the horizontal chamber pressures to the densities of excavation chamber samples, Bezuijen et al. (2005) discovered that the gradient is not necessarily representative of the muck density. They assumed that the yield stress of the muck as well as the adhesion between the muck and the cutterhead and bulkhead material have an influence on the vertical gradient during mining (Bezuijen et al. 2005, Bezuijen & Talmon 2014)."

Jan 1, 2016

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By M. A. Alan

The Bellavista Gold Deposit lies 75 Kms north west of San Jose, the capital of Costa Rica, Central America and 3 Kms north east of Miramar, in the Province of Puntarenas. The total road distance from San Jose to the deposit is 120 Kms all paved road except for a 2.5 Km graded, gravel road on the property (Figure 1). Infrastructure services in the Miramar-Puntarenas area are well developed with electrical power distribution, a modern port facility and community services being available. The deposit lies on the south west flank of the Tilaran Mountain Range between an elevation of 550 and 800 meters above sea level. The local topography is steep, originally covered with pre-montaine, tropical wet forest vegetation which has been largely destroyed due to clearing for cattle grazing. The annual rainfall is approximately 2,950 mms, 90% of which occurs between May and October.

Jan 1, 1992

By M. L. Leming

The mechanisms of Alkali-Silica Reactivity (ASR) are briefly reviewed, test methods are examined, and typical specifications are discussed. In addition, views on responsibility of the aggregate supplier regarding specifications are presented.

Jan 1, 1995

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By Gonzalo Barrientos

Instrumentation and observation of real mine structures helped define the pressure arch at White Pine, a large copper mine in sedimentary rocks. The pressure arch, which is attributed to inherent horizontal stresses, is used in the design of mine openings.

Jan 1, 1969

By Bahaa Alyosif, Turan Uysal, Muhammet Kürsat Aydemir, MURAT ERDEMOGLU

 The paper investigates the effect of intensive milling on the conversion of microcline to potassium chloride during chlorination roasting. The study aims to improve potassium recovery by reducing the chlorination roasting temperature through mechanical activation.

Aug 1, 2023

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Francis S. Kendorski

INTRODUCTION Drift design problems in caving operations are a re¬sult of the geologic factors contributing to the overall success of the system, of the engineering factors dictated by economic and technical considerations, and of ore production practices. Combining these factors, a rational underground sup¬port system of rock reinforcement, light steel channel section or welded wire fabric, and shotcrete can be de¬signed based on rock fracturing, rock load, abutment loadings, ground movement, expected repair and desired flexibility. The design concept uses the effect achieved by restraining, reinforcing, and maintaining some of the intrinsic strength of the fractured rock mass composed of interlocked blocks of intact rock and rock fractures. Three different examples of drift support design in hypo¬thetical mines using the caving system are given. Caving is a system of underground mining where ore is extracted by means of gravity after the ore body is allowed to fail by removing support from underneath. The rock mass of the ore body fractures and flows ver¬tically downward to let gravity do as much work as pos¬sible. Caving differs from many other mining systems in that blasting is used only to initiate the rock mass failure by removing the rock supporting the ore but not to break the ore itself. The initial movement of the rock mass dur¬ing failure and the consequent crushing and grinding during the continued movement serve to reduce the ore to particles of a manageable size, with only limited sec¬ondary blasting necessary. The broken ore is extracted from the bottom of the failed rock mass through funnels of some sort pre-excavated in the rock. Ore extraction must continue or the swell of the broken rock will even¬tually fill the cavity and stop further rock mass failure and movement. The excellent general discussion on block caving in the SME Mining Engineering Handbook (Julin and Tobie, 1973) adequately covers the principles and application of this type of underground mining. Many rock mechanics aspects of block caving have been covered by others (McMahon and Kendrick, 1969; Swaisgood, et al., 1972; Mahtab and Dixon, 1975; King, 1946) and will not be reviewed further. Maintaining the stability of production drifts is one of the most troublesome problems plaguing the mine manager in a caving operation. Many factors contrib¬ute to drift support problems, and identifying the causes of instability and producing a reasonable support design are two steps toward achieving stability consistent with the mine plan. This chapter sets forth a technique for the design of support systems for production drifts in caving opera¬tions. The basic support system elements employed are rock reinforcement, welded wire fabric, and shotcrete. Recognized as contributing to the design are the factors of rock load, additional load from mining activity, rock fracture characteristics, repair expected, and flexibility. It must be emphasized that the drift must first be stabilized as for a tunnel, and the additional strengthen¬ing for mining-induced loads cannot contribute to the initial premining stabilization, or the reserve of strength is used up. MINE PLANNING The efficient mine planning engineer not only must satisfy the economic, human, and environmental aspects of his task but must also consider the mechanical con¬sequences of his plan. The problems created for the mine by placing parallel drifts too close, by crossing drifts on different levels with inadequate, if any, separa¬tion, and by installing connections and crossovers in the haulage plan without regard for the effective spans cre¬ated, are only a few of the problems a mine planning engineer can create for himself and the mine. The effect on immediately adjacent mine areas when an area is caved is important to drift design because the removal of vertical support from a rock mass causes the weight of that rock mass to be shifted elsewhere. The adjacent rock mass will carry this load and reach a new equilibrium with the applied stress. The advancing front of stress increase that results from caving (and many other mining systems) is generally called the abutment load and is the increase in stress over the gravity or tec¬tonic stress that already exists, as shown in Fig. 1. In general, the abutment load will be similar in nature to the stress change found around an opening in rock and will be taken as causing an increase in the vertical prin¬cipal stress, due to an approaching caving boundary, so that

Jan 1, 1982

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By C. E. Brechtel

Bench cut-and-fill stopes with heights between 85 and 105 ft are being excavated in the lower levels of the B-NEATH Zone. Estimates of pillar strength and pillar loading indicated a high probability of pillar failure. Some changes in mining practice were made to minimize impacts of pillar failure and a rock mechanics instrumentation program was employed to monitor stability during mining of the first stopes. Limited pillar failure, in the form of destressing, was observed in the initial stopes; however, global stability during mining was good. Instrumentation data indicated that predictions of pillar strength and stress were quite close to field results.

Jan 1, 1989

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987