Search Documents

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By E. H. Ahrens

This paper deals with the daily work of operating geologists and should be of interest to recent graduates. Working with development and production is quite different from exploration and many of the required skills and techniques must be learned on the job. Try to obtain your first position at a mine where good geological work is being done because it is important that you establish a solid foundation by learning valid techniques. Many do not! Those who desire to work in exploration are well advised to spend the initial two or three years at an operating mine where they will deal daily with an orebody during development and mining. Attempt to understand the controls of ore deposition and be interested in all phases of the operation. Learn something about factors which can adversely affect profitability and you will be a better explorationist.

Jan 1, 1983

By C. Wayne Burnham

Much has been written about hydrothermal alteration and the compositional changes induced by it in the wallrocks of mineral deposits, especially in alummino-silicate wallrocks. So much has been written and the descriptions so varied, in fact, that the casual reader frequently is bewildered by the extreme complexities and lack of uniformity, real or apparent. Certainly the mineralogy and chemistry of altered rocks are not as simple as most of us would like, but neither are they as complex in their principal aspects as pa of what has been written would lead us to believe. The trend until recently seems to have been toward greater complexity and hence greater confusion, but the straightforward presentation of Creasey (1959), it is hoped, marks a reversal in this trend.

Jan 1, 1962

By Michel Gauthier

Several zinc showings, exhibiting many similarities to the well-known Balmat-Edwards zinc deposits of New York State, occur within the Grenville Supergroup strata of the Mont-Laurier Basin, Quebec. Metallogenic mapping programs have revealed much of the stratigraphic control of this mineralization. This control is observed on both regional and local scales. At the regional scale, these showings are confined to the perimeter of the Mt.-Laurier Basin, while at the local scale, a definite association between the zinc mineralization and dolomitic marble horizons is clearly exhibited from detailed mapping. These new exploration guidelines have proven to be useful for base-metal exploration in the Mt.-Laurier Basin and should be applicable to the entire Grenville Province.

Jan 1, 1983

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By Richard S. Kunter

The Bulldog CIP plant treats the slime portion of current tailings and reclaimed flotation tailings from the adjoining 350 tpd (3.67 kg/s) silver-lead flotation mill. Changes to the dredge reclaimer, pulp storage tank and trash removal system have allowed an increase in tonnage treated to a sustained 460tpd (4.83kg/s). CIP feed is 3-4 oz/T Ag (102.9-137.1 ppm). Following conventional cyanidation, carbon is added to the slurry. Silver loaded carbon is stripped in atmospheric-pressure vessels using hot caustic cyanide. Silver recovery from this solution is by Zadra- type cells. Some of the modifications to the plant and operating techniques are discussed.

Jan 1, 1981

By D. Lauriski, E. D. Thimons, A. C. Smith, D. C. Fredley

The National Institute for Occupational Safety and Health (NIOSH) and Northwest Barricade LLC (NWB) conducted a study to evaluate the effectiveness of a novel fire blocking gel for use in underground coal mines to extinguish or retard the growth of a coal fire. The gel agent was subjected to controlled laboratory testing to assess its ability to delay coal ignition. It was then evaluated to determine if manual fire hose application could be used to apply the agent to mine roofs and ribs to provide a safe egress for mine rescue teams from a fire area. The gel agent was also evaluated in a water sprinkler system to determine its potential for use in conveyor belt fire suppression systems. The agent was then tested in live-fire exercises to examine its effectiveness in retarding and extinguishing a deep-seated coal fire and wood fire. Lastly, the ability of a mine rescue team to quickly and safely apply the gel agent to a mine entry during a simulated mine fire exercise was determined.

Jan 1, 2011

By E. K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. While providing a useful tool for the investigation of mine planning problems, the availability of graphic output was limited or non-existent. Computer graphics is a natural extension of mine simulation methods and provides a more dramatic level of understanding and interface with an engineer. With today's high cost of venture development, the need for an easy to use but complete systems model which includes the major elements of mine planning with an interactive graphics interface has never been more apparent. In this paper, the underlying philosophy of design of an interactive interface to a complete surface mining simulation model is described. The basic structures of the surface mining system and the simulation model are discussed. The methods and algorithms used to implement the various subsystems are presented. Practical considerations of the design of displays and user interaction are illustrated, especially as they apply to the application of the package by a mining engineer. A simple example is provided to demonstrate the concepts embodied in the model and to show how a simulation is built from mine data.

Jan 1, 1984

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By Whitmell J. Smithwick

Lime is one of the most extensively used chemicals in industry. Other than sulfuric acid, it is used in greater quantities than any other man-made industrial chemical. In 1974 there were 20,368,000 tons of lime used in the United States, which amounts to approximately 190 pounds for each man, woman and child in our nation. Lime also is perhaps the most diversely used of any industrial chemical. It is used in such areas as pharmaceutical, chemical, steel making, glass making, production of copper and aluminum, sugar refining, agriculture, construction, ecological endeavors, potable water treatment and sanitation. Figure I lists the major uses of lime for 1974, which is the latest year for which this data is available. The impact of the use of lime for ecological reasons did not show up to any appreciable extent in 1974, but we expect this to be a significant factor within the next few years. Fortunately, in the United States and also in most of the world, there are many deposits of high quality limestone available for the production of hood quality lime. For this discussion, we will assure that a limestone of a suitable quality and size consist will be available in a storage bin or stockpile near the kiln. Quality requirements for the lime product will be covered. We also will give a brief description of the three most popular types of lime calcining systems, how they function, and expected lime product quality from each of these. Commercial fuels and major accessory equipment will be discussed briefly.

Jan 1, 1976

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By D. Robert Weir, Verner B. Sefton

The reduction roast-ammonium carbonate leach-hydrogen reduction process for laterites has been under development by Sherritt Gordon for the past 20 years. The process can treat high iron or low iron laterites, with some process modification, and gives extractions of 88-93% Ni or 82-88% Ni, respectively. Five campaigns on a 1 tonne per day Pilot Plant and four campaigns on a 35 t/d Demonstration Plant have been carried out on laterite from three different deposits, and many other laterites have been investigated in the laboratory. The Marinduque Surigao Nickel Refinery in the Philippines was designed on the basis of this work. The process comprises roasting to selectively reduce the nickel and cobalt in the laterite, leaching the calcine in ammonium carbonate to dissolve the metals, recovery of cobalt by precipitation of a mixed metal sulphide, concentration of nickel from the carbonate solution by basic nickel carbonate precipitation and recovery of high purity nickel by hydrogen reduction of nickel from ammonium sulphate solution. Ion exchange has been developed as an alternative to BNC and for recovery of trace nickel from BNC barren liquor. Details of the development of some of the process steps through the laboratory to commercial plant are discussed. The process metallurgy has been confirmed in the commercial plant.

Jan 1, 1979

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed