Search Documents

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

By N. Duru, C. Nesbitt

During the cyanide leaching process, gold and silver ores that come from the transition zones, which typically contains low levels of sulfide, may produce one or more of the following reduced sulfur species: sulfide ( HS−), polysulfides ( Sn 2−), thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−), pentathionate ( S5O6 2−), hexathionate ( S6O6 2−). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the redox potential, pH, cyanide levels, and existing sulfur species in recycled process water, as well as the presence of other reactive metal species. The development of an accurate analytical method for sulfur species in cyanide leaching units of gold ores where sulfur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and the development of ion chromatography method to analyze reduced sulfur species thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−) in cyanide leaching circuits for gold ores. The method developed has resulted in precise quantification of target sulfur species in leach solutions. Method development and validation results were illustrated on analytical graphs containing each species’ peak number, retention time (min), type, width (min), area (mAU*s), height (mAU), and area distribution (%) of the peak.

Mar 2, 2024

By K. A. Natarajan, Abha Kumari

"The effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. The effect of applied potentials and electrolytic currents on the activity and growth of bacterial cells was assessed. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and biocatalysis of anodic oxidation. IntroductionIn recent years, the bioleaching of low-grade chalcopyrite ores as well as their flotation concentrates has been receiving increased attention. Use of mesophilic bacteria such as Acidithiobacillus ferrooxidans in the bioleaching of chalcopyrite does not yield desirable copper extraction rates due to its easy passivation.Bioleaching of chalcopyrite using A. ferrooxidans has been reported to be very inefficient, and use of thermophilic bacteria at higher temperatures is recommended to improve its bioleaching rates. Bioleaching under imposed applied DC potentials or currents has been shown to enhance not only bioleaching kinetics but also to confer selectivity in mineral dissolution (Abhakumari, 1996; Chirpa Selvi and Natarajan, 1998; Natarajan, 1992a, b,c). Electrochemical principles governing electrobioleaching have been earlier illustrated (Jyothi et.al, 1989). The role of applied potentials on the activity and growth of A. ferrooxidans has also been studied (Natarajan, 1992b). Also, the electrochemical aspects of bioleaching of several sulfide minerals when present alone or in binary and ternary combinations have been reported (Jyothi et al., 1989). The electroleaching of copper-nickel concentrate (Natarajan et al., 1985) and electrobioleaching of sphalerite concentrates have already been studied (Selvi et al.,1998). However, it is possible to enhance the bioleaching rate of chalcopyrite in the presence of A. ferrooxidans under galvanic conditions in the presence of nobler minerals such as pyrite (Jyothi et al.,1989). Also, dissolution of chalcopyrite can be significantly enhanced under applied potential conditions. Ali Ahmadi and his coworkers recently studied the electrochemical bioleaching of chalcopyrite concentrates using moderate thermophiles (Ahmadi et al., 2010, 2011)."

Jan 1, 2015

By A. H. Sharbaugh

It is believed that considerable economic benefit would arise if run of mine (ROM) coal from the underground mines in the Winifrede seam could he enriched before shipment to the preparation plant by partial removal of the shale. Shale could comprise up to 50% of the ROM product. Complete mine-mouth separation is not necessary, but any process must be dry and have high Btu recovery. We have conducted a preliminary analysis of coal/shale mixtures from the Winifrede seam and we find that it is quite possible that a 50-50 ROM mixture of coal and shale could be converted to a 60-40 coal-shale mixture by inspection of individual lumps coming from the mine. The device would consist of a feeder/siever section to deliver the ROM coal > 5 cm (2 in) to an inspection station via a conveyor belt. This inspection station decides if a piece is coal or shale, and if it is shale, activates an air jet to blow shale off of the belt. We have evaluated a dielectric loss technique for the inspection device. The potential advantages of the dielectric loss method are high throughput, low capital cost, and no special handling or licenses would be required. Such a single lump inspection technique is made possible because of advances in high speed electronics and servo systems. This paper provides a summary of our analyses on the Winifrede coal sample, a description of a proposed apparatus to separate coal from shale, some of the experiments needed to demonstrate our ideas.

Jan 1, 1984

By X. F. Wang, K. B. Fu

"We investigated experimentally and theoretically the adhesion behavior of Acidithiobacillus ferrooxidans (At.f6) to different copper sulfides. The adsorption experiment showed cell densities of 10.74 × 106, 8.06 × 106, 3 × 106, 4.24 × 106 and 2.35 × 106 cells/cm2, respectively, on the surfaces of djurleite, bornite, covellite and chalcopyrite. The order was: djurleite > bornite > covellite > chalcopyrite. The results indicate that A. ferrooxidans has high affinity to adhering to the surfaces of djurleite and bornite in the acidic region. But the thermodynamic approach predicts that there will be no attachment of At.f6 to the surfaces of bornite, covellite and chalcopyrite. This discrepancy is due to the inadequate description of electrostatic interactions. The DLVO approach shows attachment of At.f6 to the surfaces of djurleite, bornite and covellite, and repulsion between At.f6 and chalcopyrite. The DLVO approach can explain the differences of the adhesion of At.f6 to different copper sulfides.IntroductionThe bioleaching of low-grade copper sulfides is a developing technology, and has been applied successfully to the extraction of copper from secondary sulfide minerals (Watling, 2006; Pradhan et al., 2008; Akcil and Deveci, 2010). The bioleaching of chalcopyrite is still a major challenge (Bosecker, 1997; Brierley and Brierley, 2001; Ehrlich, 2004). A study conducted at Billiton Process Research showed the following preferential order of sulfide minerals leached by mesophilic cultures: chalcocite > bornite > cubanite > covellite > pyrite > enargite > carrolite >> chalcopyrite (Dew et al., 1999). The bacteria can solubilize the valuable metals from the orebodies by the oxidation of minerals. Bacterial adhesion plays a critical role in the bioleaching processes (Chen et al., 2008; Harneit et al., 2006). Generally, bacterial adhesion can be explained by surface thermodynamics and the extended DLVO theory, in which the adhesion energy between the bacteria and mineral is calculated as a function of the separation distance (Sharma, 1999; Bos et al., 1999; Sharma and Hanumantha Rao, 2002). These methods take into account Lifshitz-van der Waals interactions, electrostatic interactions and acid-base interactions (Busscher et al., 2010). These interactions are very well understood and formulated in mathematical equations. The most important inputs in these calculations are surface energy, surface charge, electron donation and electron acceptance on the bacterial cell surface and mineral."

Jan 1, 2015

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll in the US coal mining industry. Recent health surveillance data indicates that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied in order to reduce dust levels. An overview ofCWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

Jul 30, 2020

By V. Aghazadeh, E. Bidari, M. Aazami

In this study, mineralogical and microanalysis characterization, as well as diagnostic leaching and cyanidation tests, were performed to gain a better understanding of the refractory nature of the arsenical zone of a Carlin-type gold deposit and also to evaluate possible treatment routes to maximize gold recovery. The results obtained showed that only 56% of the ore’s gold content is amenable to direct cyanidation. The majority of the remaining gold was found as submicroscopic gold and in association with sulfide minerals, such as orpiment, pyrite, and sphalerite. It was also found that despite the abundance of silicate and carbonate minerals in the arsenical zone, they do not play a key role in the refractory nature of the ore, and gold can be liberated from such minerals by appropriate grinding. The analyses further revealed that orpiment dissolves readily during cyanidation, and this dissolution retards the kinetics of gold extraction. Pyrite and sphalerite were generally found to occur in fine network texture and in association with quartz. Flotation of such auriferous sulfides may be difficult due to their oxidized surface. Fine grinding (−20 μm) was found to be partially effective in improving gold extraction.

May 28, 2020

By Charles V. Riley

While the late 1960's are known as the years of the public recognition of impending environmental crises, the 1970's will be known as the decade of public concern for improving the quality of that environment. One of the present major environmental concerns is the temporary disturbance resulting from coal surface or open cast mining. To realize that this concern will continue in the future, one need only observe the daily news media. Increasing energy demands in the U.S., a doubling of electrical power consumption each decade during the present century, and the projected needs for the remainder of the century are indica¬tions that coal surface mining as a major extractive industry will continue. Coal and lignite, prime energy resources and extremely abundant in these United States, in the face of seemingly limited gas, oil and uranium reserves, are both destined for expanded future use. Presently some extremely serious techno-logical and environmental problems are associated with the develop¬ment and use of nuclear power. It is true that the extraction and use of coal as an energy fuel poses disruptive problems for the environment, but the solutions to many of the problems are known or can be solved within a reasonable time framework. Certainly our national well-being and continued survival, as a free nation within the world community, automatically dictate the continued use of the coal resource for energy. Concurrently, those engaged in coal surface mining, with the temporary disturbance of the land and water resources, must also realistically conclude that public concern for maintaining and improving the quality of the environment will not diminish. Although as ecological, economic, social and aesthetic elements

Jan 1, 1972

By Tracey A. Conrad, Mark E. Mussett, Max Kaufmann

The varied benthic habitats of the Pacific Ocean are comprised of different types of seafloor geology. These geologic domains generally consist of sedimented abyssal hills, high relief features such as seamounts, and polymetallic nodule fields that vary in spatial extent and abundance. Nodules represent a deep ocean habitat type, and are of economic interest owing to their metals content. Multibeam data can be used to classify seafloor geology. The wide swath of hullmounted multibeam systems used in deep water provides efficient coverage of large areas of seafloor. Our research examines how multibeam backscatter and bathymetry data, with regional environmental parameter assessments and GIS analysis, can help identify probable polymetallic nodule fields in the deep remote ocean prior to groundtruth seafloor observations. A workflow for processing 30 kHz hull-mounted multibeam data within QPS Qimera and FMGT software was developed to facilitate multibeam processing, while also generating a terrain model and backscatter products. An additional GIS protocol for evaluating multibeam data products, including cluster analysis, was also developed. These methods were applied to a test case of publicly available multibeam data collected by the Ocean Exploration Trust and NOAA. Processed multibeam products were used to identify areas exhibiting coarse sediment backscatter characterization with low relief; filters for water depth at or below the regional CCD, seafloor age, and sedimentation rate were then applied. Sophisticated GIS cluster analysis further identified trends within the data to forecast where coarse sediment domains, potentially including nodule occurrences, exist. The test case multibeam data allow determination of the composition and variability of seafloor geology. This analysis can further identify where previously unexplored nodule fields may exist and edify estimates of nodule extent throughout the ocean. The research methods and outcomes contribute to marine spatial planning, ecosystems modelling, and mineral resource management initiatives.

Feb 22, 2026

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

By Matthew Deutsch

A common casualty of modern open-pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper, all of these problems are addressed by encoding these three fundamental open-pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot.