Search Documents

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By S. D. Irons

With the passage of recent national and state legislation aimed at tighter regulation of air pollution and smoke control, attention has been focused on a problem which has long confronted the coal industry--the disposal of coal waste with its inadvertent ignition. Even as recent as 1935, a decision from the Allegheny County Court of Common Pleas confirms the stand taken on control of burning coal refuse disposal areas. "The uncontroverted testimony is that there is no feasible method of operating a coal mine without a gob pile on the surface, as no use has ever been found for this troublesome by-product of mining; that every large coal mine has a large gob pile close to its tipple; that sooner or later these piles all ignite through spontaneous combustion; that practically every large mine in Western Pennsylvania has a burning gob pile, and that there is no known means of averting such a fire." 19* As a result of the past "no regulation policy," there are presently on the order of 500 burning refuse banks, of which 213, 142, and 49 are found in West Virginia, Pennsylvania, and Kentucky, respective¬ly. 18 Many of these refuse banks have burned for 40 years or more; many others may continue burning for a like period. It is estimated that the annual emission from these smoldering piles approaches 183,000 tons of pollutents which may produce many deleterious effects on the populace, property and vegetation in the proximity to the sources.16 To date, little progress has been made in alleviating the pollution from the currently burning refuse banks; however, numerous investigators who are researching the causes of ignition, as well as preventative disposal techniques (refuse compaction, layering and crushing to finer sizes) have met with some success in handling the newly discarded coal refuse.

Jan 1, 1967

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By E. Krist

The newest addition to the Anamax Mining Company's Twin Buttes copper producing complex is a by-product uranium extraction plant which was placed into service in February 1980. The plant is unusual in that it is placed internal to the copper countercurrent decantation, solvent extraction, and electrowinning plant. The plant reached full production within a month and, to date, has produced continually above design rates.

Jan 1, 1981

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

Despite several methods (empirical, statistical and machine-learning tools) to calculate blast-induced ground vibration, it is not easy to predict and simulate blast vibration precisely under varying blasting loads and strata conditions due to complications in the blasting procedure. In this study, field blast data were simulated in Ansys software using explicit dynamics, and ground vibrations for 20 single-hole blasts were monitored. The densities of emulsion explosives were in the range of 0.9 to 1.15 g/cm3. In the laboratory, rock properties were determined from rock samples collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and density of the emulsion explosive were also determined and used in numerical analysis to know the ground vibrations at specific points. The results of ground vibrations predicted by the model were validated using field data.

By J. R. Aggson

In an effort to minimize cutter roof failures in longwall development entries of a West Virginia coal mine, a three-entry system was developed with the center entry arched into the strata above the coal seam. The purpose of the arched entry was to modify the horizontal stress envelope associated with the three-entry system and improve roof conditions in the adjacent outside entries. Contrary to the predictions of elastic analyses, the presence of the arched entry improved roof conditions by eliminating cutter roof failures in the outside entries. In-situ stress determinations and numerical modeling techniques were employed to quantify the impact of the arch and investigate the mechanism of stress relief associated with the arched entry. Stress determinations and underground observations indicated that the roofs of the outside entries were within the zone of stress relief generated by the arch, and that failure or movement along bedding plane discontinuities played a major role in the formation of the stress relieved zone. The numerical model incorporated horizontal joints to simulate bedding plane discontinuities. The properties of the joints were adjusted until roof stresses predicted by the model were in agreement with measured stress profiles. This process resulted in a calibrated analytical tool that could be used to evaluate alternate mining geometries.

Jan 1, 1988

By Stacey Leichliter

The Cripple Creek and Victor (CC&V) Gold Mine (Cresson Project) (Fig. 1) is undergoing an expansion to extend production to the year 2025. This expansion involves building a high-grade ore mill, another valley leach facility (VLF) for heap leach operations and expanding the overburden storage areas. The current operating pits are progressing downward from the oxide ore into a more sulfide and telluride-rich orebody. There is still oxide ore present in the current pits and planned pits not yet mined. There is an increased need for two recovery processes for these two different types of ore. The key component to this expansion is the high-grade ore mill, which has gravity, flotation and carbon-in-pulp (CIP) circuits. The mill will be the main recovery process for the higher grade, more sulfide/telluride-rich ore. This ore type does not recover well on the heap leach pad due to its refractory nature. Geometallurgy is vital for ore characterization for the two recovery methods. Geometallurgy helps develop indices that are used to predict parameters that influence overall recovery and production, such as hardness, crushability, grindability, pH fluctuations, gravity (coarse) gold, flotability and cyanidability. Using geology and mineralogy along with other analytical data, geometallurgical models are constructed and applied to the resource block model for proper planning and extraction of the gold. Geometallurgy aims to analyze the variability in the different responses to the parameters to help reduce risk (costs) and optimize recovery (profit).

Jan 1, 2013

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By James R. Strong

Before getting into the subject of packaging and materials management, please permit me to introduce you to MICRO SWITCH. MICRO SWITCH, A Division of Honeywell Inc. is located in Freeport, Illinois. We manufacture and market thousands of types of precision snap-action electrical switches. Most of them are used as components by other manufacturers in industrial and commercial products. MICRO SWITCH also offers a broad line of industrial control devices including heavy- duty limit switches, relays, manual controls and proximity switches. Other product lines are solid state keyboards for the computer industry and high-performance d.c. motors used in computer related equipment. So you can see that we are a component manufacturer. With the exception of the keyboards, every one of our products would "fit comfortably into a breadbox." Some are so tiny that one could easily fit several thousand into a man's hat. In my position as supervisor-packaging. package design, and materials handling engineering, I am actively involved in package design projects, parts handling design projects, and numerous activities involving departmental layouts, storage facilities, and material handling equipment. Two package design technicians, a materials handling engineer, and a materials handling technician make up the technical staff.

Jan 1, 1973

By James S. Browning

The Mineral Resources Institute of The University of Alabama conducted research on the removal of sulfur from coal using a combination of gravity concentration and flotation methods. The research utilized the gravity and centrifugal force capabilities of the Humphreys spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphreys spiral coal concentrate removed additional sulfur and ash to yield products that conform to Federal air quality standards for sulfur oxide emissions. The clean coal products recovered by the combined process contained 7.7 to 8.0 percent ash, 0.12 to 0.16 percent pyritic sulfur, and 0.78 to 0.96 percent total sulfur. Pyritic sulfur rejection by the process was about 95 percent. In addition to obtaining good recoveries of high quality coal the tests demonstrated that the pyrite in the wastes could be isolated as enriched flotation products by the combined gravity - flotation apporach. Pyrite concentrates analyzing 25 to 33 percent sulfur were recovered. Potential benefits of the pyrite flotation step are recovery of a product of possible market value and the elimination of the pyrite from the waste ash which could be a potential acid water problem when impounded.

Jan 1, 1981

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By Linda J. Dahl

The U.S. Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ leach mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits which include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, proximity of ore minerals to the leach fluid paths, surface subsidence potential, and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental, and economic feasibility of in situ leach mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability, and porosity as they relate to in situ leach mining.

Jan 1, 1992

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By C. Roos

"Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years. However, many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize, and even embrace, the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process.Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation, but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple orebody realizations to provide a thorough unbiased picture of the geologic uncertainty. However, most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter.Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this article presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid- to long-term mine plans while continuously monitoring the uncertainty in the results. The aim of this article is that by demonstrating the usefulness of such a system, mining companies will encourage engineers, geologists and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 8, 2017

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By Gary Brierley, Lok Home

"The majority of tunnels for civil engineering applications are now being constructed using some form of mechanical excavation. Beginning in the 1960s with rock tunnel boring machines (TBM), the tunneling industry has introduced both earth pressure balance (EPB) and slurry pressure balance (SPB) soil machines; mixed soil and rock machines and a variety of different mechanical devices for the construction of small diameter tunnels. Over time, these machines have become more powerful and more adaptable to a wider variety of ground conditions; so much so that tunnels are now being constructed in ground conditions and in the vicinity of third-party impacts that would have been considered beyond the state of the art just 10 years ago. Figure 1 is an example of a mixed ground crossover TBM used successfully at Mexico City’s Túnel Emisor Poniente II.All of the above is highly advantageous for the tunneling industry, but it has also placed a much higher level of risk on the performance characteristics of the tunneling machines, on the contractors operating those TBMs and on the manufacturers of those machines. Most of the risks for a tunneling project are associated with creating the space inside of which the finished facility will be constructed. In order to create that space, the tunnel contractor must make many decisions about the best way to excavate the ground, the best way to control the ground at the face of excavation and the preferred method for supporting the ground around the tunnel in a manner that is safe for the workers and stable with respect to all of the overlying and adjacent existing structures. If it is proposed to use some form of TBM in order to build the tunnel, then the TBM becomes central to all three of these activities and becomes an integral part of managing the risks associated with these activities."

Jan 9, 2018