Search Documents

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acid-insoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Jan 1, 2011

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By Mamookho Elizabeth Makhatha, Mbal Henock‑Michel Mwanat, Kubangala Brest Kasongo, Ntumba Edward Malenga

This study investigated the operating parameters that affect the kinetic dissolution of copper and cobalt from sulfidic ores. The sulfuric acid concentration, temperature, sodium chloride concentration, particle size range, and leaching time were selected to deduce the kinetic mechanism of the leaching reaction. Other parameters, such as a stirring speed of 250 rpm and the percentage solid 10% w/v, remained constant. The results reveal that an increase in acid concentration enhances the leaching rate of copper and cobalt. Copper and cobalt dissolution was positively affected by the addition of sodium chloride. The highest leaching rates of copper and cobalt were 24.71% and 15.65%, respectively. The chemical control and diffusion control by shrinking core models are well fitted as the kinetic models representing the dissolution of the minerals. The respective activation energies for copper and cobalt dissolution of 10.92 and 31.023 kJ mol− 1 for the chemical control and 18.83 and 37.28 kJ mol− 1 for diffusion reaction control were established from temperature-based experiments.

Aug 26, 2022

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By J. H. Howard

The purposes of this report are to summarize the findings of the Committee on the Challenges of Modern Society Non-electrical Project (a working committee of the North Atlantic Treaty Organization) and also, thereby, to provide an introduction and review of the current situation regarding non-electrical applications to those who are interested in the subject.

Jan 1, 1975

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020