Search Documents

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By J. D. Miller

Many factors -- political, environmental and technological -- will determine the extent to which the United States realizes the potential of its vast coal resources. Not the least of these factors is technogical development including mining, processing and transportation. With regard to processing technology, about 50% of the 800x106 tons of coal mined annually in the U.S. is processed in preparation plants. The purpose of the physical separations accomplished in these preparation plants is to remove ash (present as clays and other oxide minerals) and sulfur 'present mostly as pyrite). Coal flotation circuits for such separations are becoming more important in the processing of minus 28 mesh coal. (1,2,3) For example in the U.S. in 1960, 31 flotation plants processed 26,500 tpd; whereas in 1980, there were 80 flotation plants which processed 78,300 tpd. This corresponds to an annual growth in flotation plant capacity of 10 per year during the past two decades. Coal flotation is based on the natural or induced hydrophobicity of coal particles which are separated from hydrophilic ash and sulfur constituents by attachment to air bubbles. The coal particle/air bubble aggregates are collected in a froth phase which is created by the addition of a suitable frother such as MISC. Without exception, such separations are made in a conventional flotation cell, which, in essence, is a stirred tank reactor with a shrouded rotor to shear the air as it passes through a hollow shaft. The dispersed air bubbles (4.0 mm diameter) are stabilized by addition of the frother. Collision of the air bubbles with, and/or precipitation of the air bubbles on, the coal particles results in the formation of coal particle/air bubble aggregates which rise in the gravitational field and are collected in the froth phase developed at the top of the flotation cell. Restraints on successful separation by this conventional flotation technique are particle size and retention time. Generally it is found that effective flotation is only achieved for particle sizes between 10 and 1000 microns. Further, with respect to retention time, it is found that a nominal retention time of at least 2 minutes is required for successful separations. These facts limit the effectiveness of conventional coal flotation. Coal fines may be lost in the reject stream and disposal is frequently a problem. The retention time required for conventional flotation results in large floor space demands which limit the capacity of the plant.

Jan 1, 1981

By Wang Ding-heng, Wang Zhi-yuan, Nolan B. Aughenbaugh

The People's Republic of China has abundant coal resources with proven reserves amounting to 582 Gt (641 billion st). Recognizing coal as a major energy source on which to build the country's industrial and economic base, there has been a rapid increase in production since the founding of the People's Republic. In 1949, only 29.4 Mt (32.4 million st) of coal was mined. Production has increased to 576.5 Mt (635.5 million st), exclusive of Taiwan, at present, making China the third largest coal producing country in the world. Plans call for a 4-5% increase in annual production for the next 20 years. Coal constitutes 70% of the primary energy consumption in China. The remaining 30% is divided between petroleum and natural gas with 26% and hydropower with 4%. Coal use and consumption is divided as follows. General industrial use comprised 48.9%, power generation uses 20.1%, and coking accounts for 10.5% (6.3% for metallurgy and 4.2% for chemical industry). Domestic use such as home heating and cooking makes up 17.8% and coal-fired steam engines for railways uses 4.7%. Coal Districts Coal underlies about 1/18 of China's land area. It occurs in 30 provinces, autonomous regions, and municipalities. In addition, the western interior region, which has not been explored, may contain sizable reserves. Based on geology, geography, and administration, the coal fields can be grouped into five districts as shown in Fig. 1. The north China district, the heart of the industrial base for the country, has the most extensive and largest deposits of the five districts. This amounts to almost 40% of the country's total reserves. The largest coal basin with proven reserves of 181.4 Gt (200 billion st) and the most exploitable seams is located some 300 km (186 miles) southwest of Beijing (Peking) in Shanxi Province. Centered around Taiyuan, the compound field extends from Datong in the north to Xian in the south. Its western extension is not known fully. The Northwest and Northeast districts contain the second and third largest deposits. The biggest coal field in South China is located in the Sichuan and Guizhou Provinces near Chongqing. At present, it is not known if sizable coal measures exist in the Tibetan district. Coal Types China's coal varies widely both in age and rank. Geologically, coal measures were deposited from the lower Carboniferous (Pennsylvanian of the US) and Permian of late Paleozoic, mainly during the Jurassic of the Mesozoic and peri¬odically throughout the Cenozoic. Collectively, coal from the lower Carboniferous, Permian, and Ju-

Jan 3, 1983

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Aline Tatom

This paper presents numerical and experimen¬tal results dealing with the application of ferric ion oxidation of uranium in acidic media. Conclusions are derived from matching numerical results to experimental data taken on one-dimensional laboratory leaches using ore from a South Texas Coastal plain deposit. Since the numerical results can be made quite general, we are able to extract and quantify the effects of oxidant concentration, flow velocity, mass transfer, chemical kinetics, and competitive oxidant consumers (pyrite and molybdenite) on the experimental results. Our results suggest that the leaching of uranium is a mass transfer controlled while that of pyrite is kinetically controlled.

Jan 1, 1981

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By J. van der Walt

The Meikle Mine is located in the northeastern part of Nevada in the gold-rich Carlin Trend. First discovered in 1989, Meikle is being developed into a 2.2-kt/d (2,500-stpd) underground mine that will open during the second half of 1996. Work has already been completed on the mine’s cooling plant, a necessary item due to the high rock temperature and the hot ground water. In North American mines, there has been little need for refrigerated cooling. Therefore, Barrick needed to draw on experience from elsewhere in the world — particularly South Africa — to meet these requirements. The history of cooling mines using mechanical refrigeration dates back to the 1920s at Morro Velho in Brazil and 1936 at Ooregum in India (Dobson,1940 and Biccard, 1946). From 1940 to 1960, several cooling plants were installed on the deep level gold mines on the Witwatersrand in South Africa. These were followed by similar installations on the mines in the Klerksdorp, Welkom, Evander, Rustenburg and Thabazimbi areas. The first mine cooling plant in Germany was built during 1976.

Jan 1, 1996

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963