Search Documents

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

TABLE TUNNEL NAME OWNER LOCATION STATE TUNNEL USE LENGTH (FEET) WIDTH (FEET) BID YEAR STATUS Gateway Tunnel project Amtrak Newark NJ Subway 14,600 24.5 2015 Under study

Sep 1, 2013

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world's silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry's future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 Mpa (3000 psi) as compared to a surface cleaned at 0.7 Mpa (100 psi).

Jan 1, 2002

By N. B. Aughenbaugh

Subsidence due to abandoned coal mines has received copious attention recently. This is a result of many factors such as the enactment of new mining laws and the effect subsidence has on land use over the mines. Prediction of subsidence features and the time aspects over supercritical extraction (i.e., longwall and high extraction ratio pillaring) is relatively accurate. However, predicting when subsidence will occur and the surface features' size and shape above subcritical extraction of room and pillar mining is not yet possible. This paper will discuss the factors that influence the time aspects of subsidence in room and pillar mining.

Jan 1, 1983

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

Nautilus Minerals and Neptune Minerals are betting that the next great metals rush will take place more than 1,500 m (5,000 ft) below the sea. Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulfide (SMS) deposits. Its main focus is the Solwara 1 Project, a polymetallic copper, gold, zinc, silver deposit that is under 1,600 m (5,200 ft) of water off the coast of Papua New Guinea in the western Pacific Oceans? Rim of Fire. Nautilus Minerals, in a joint venture with Placer Dome (now Barrick Gold), began its exploration of what would become the Solwara 1 area in 2005 with side scan sonar and dredge sampling. The dredge and grab sampling confirmed the grade tenor of earlier sampling by scientific research programs. The 45 dredge samples aver-aged 10.8 percent copper, 3.7 percent zinc, 224 g/t (6.5 oz/st) silver and 13.7 g/t (0.4 oz/st) gold. Nautilus has since staked out more than 300,000 km2 (115,800 sq miles) of tenement licenses and exploration applications in the waters off Papua New Guinea, Fiji, New Zealand, Tonga and the Solomon Islands. That is an area about the same size of the United Kingdom. Interest in Nautilus and its projects has grown tremendously since its inception. The company is now listed on the Toronto Stock Exchange. It has raised more than $300 million and spent more than $23 million on exploration. The company has gained the backing of mining majors such as Teck Cominco, Epion, Anglo American and Barrick Gold. It is positioned to become an emerging producer in 2010. Teck Cominco recently agreed to exercise share purchase warrants to acquire three million additional common shares of Nautilus at a price of US$15 million. This will take Teck Cominco?s shareholding to approximately 7.2 percent of the issued shares. Teck Cominco will conduct and manage a ship-based exploration program that will run in addition to the exploration that was already planned for 2008.

Jan 1, 2008

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By J. T. Bartlett

Life-of-mine process simulation is an interdisciplinary effort and a useful means of thoroughly evaluating mining and minerals projects. Communication between geologists, mine planners, miners, metallurgists, and managers not only benefits each discipline but facilitates design of an efficient operation and allows for accurate forecasting of productions and cash flow. By focusing on the key areas: geology; mine design; waste dumps; stockpiles; metallurgy; weather data; tailings disposal; using contours, block models, mine plans, process flowsheets, design criteria, operating and control strategies, maintenance schedules, and operating costs to perform detailed daily simulation from start-up to shut-down; a comprehensive understanding for all disciplines is achieved. Construction of a METSIM model that includes all test work and project data from drill holes through net present value calculations brings the pieces together to achieve optimum process design, minimize operating problems and eliminate the term ?black box? from project meetings and discussions.

Feb 27, 2013

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009