Search Documents

By Y. C. Guan

The cementation of gold on to copper and zinc in ammoniacal solutions has been studied using rotating disc electrodes. The cathodic reduction of aurous ammine was studied on a gold rotating disc electrode and the anodic dissolution of copper and zinc was studied in the absence of aurous ammine. The cementation rate was found to be a first order with respect to the concentration of aurous ammine and to be proportional to the square root of the disc rotating speed. Based on the results obtained, it was concluded that the cementation reaction was controlled by mass transfer of aurous ammine to the reaction surface under the experimental conditions.

Jan 1, 1995

By C. E. Silverblatt

The advent of larger quantities of -1/4 inch coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content.

Jan 1, 1964

By Andrzej M. Wala

A knowledge of the friction factor (K-factor) is necessary in planning and designing mine ventilation systems for least cost and highest effectiveness. The friction factor used must be accurate and reliable for correct estimation of airway resistances. At present, the friction factors are determined by using tables of published values. These values were established principally for metal-mine openings having small effective areas. This presents a problem to the ventilation design engineer whose responsibilities center around the design of effective ventilation systems for large room-and- pillar mechanized underground coal mines. Friction factors selected from these tables could be excessively conservative for large scale room-and- pillar operations. With only limited data on the K-factor (which are considerably site dependent) for Kentucky's coal mines and for all the above mentioned reasons, it was concluded that there is a need for field investigations to determine these values in-situ for existing mining conditions in Kentucky. The author describe the study carried out in ten coal mines located in eastern and western Kentucky and present the results of the investigation in both tabular and graphical form.

Jan 1, 1991

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Steve Kral

When the price of gold cracked the US$9.60/g(US$300/oz) mark last year, the gold-mining industry began to crank up again. This followed several years of gold prices that had languished in the mid-200s. Existing mines increased production and mines that had lain dormant for many years were getting second looks. The United States still produces a large amount of gold. But not much of the new production is coming from that country. Instead, strict environmental regulations still have companies wary of trying to invest the millions needed to start a new mine or expand existing ones. And after years of studies and negotiations between legislators, environmental interests and the mining industry, the United States still has not crafted a new mining law.

Jan 1, 2003

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once an analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at its power plants. A quality assurance program can also help a mine deliver a consistent product to a utility's power plants. The importance of accuracy, timeliness and consistency are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By Robert E. Frey

Regardless of the mechanical design features of a particular air classifier certain basic principles apply. Specifically , there are two forces at work: 1. An air drag force 2. An inertial or centrifugal force. The air drag force has an increasing influence as particles become smaller. A very small low mass particle is easily carried along with an air stream even when turning a corner. Thus, fine particles follow the air away from the classifying zone. Inertial forces increase as the mass of a particle gets larger. Thus oversize particles tend to obey Newton's laws and respond to centrifugal forces or simply continue in a straight path when the airflow changes direction.

Jan 1, 1985

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007