Search Documents

By D. P. Richards

Tunneling in carbonate sedimentary rocks such as lime stones and dolomites can be difficult when solution channels or voids are anticipated. Addressing the risk aspects associated with these formations can be done effectively through the Geotechnical Baseline Report (GBR) by properly characterizing the ground and ensuring that the Owner?s and the Contractor?s interests are represented and protected. This paper presents a review of tunneling difficulties in these rocks and includes a review of site investigations, geologic characterization, and presentation in the GBR. Key construction issues are also discussed, including appropriate excavation technology, mechanisms of face support and groundwater control, and quantifying grout takes.

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By O. Konovalov, M. Zhuravkov

In report the results of performance of research works on building up of the connected geoecological and geomechanical monitoring system for modelling and study of a state of mining massif in a region with large-scale underground mining works are discussed. The connected geoecological monitoring requires radical change of methodology of carried out works. To carry out modelling and researches it is impossible without construction of the integrated connected information model of region. Basis of construction of information systems and databases for all sections of Earth Sciences is the set of the approaches, among which, for example, methods of remote sounding, GIS- and GPS-technology etc. Computer technologies are basis on the "supercomputer" technology. The results of performance of some researches for regions of excavation of deposits of potash salts in Russia and Belarus are presented.

Jan 1, 2005

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979

By Samuel A. Reipas

Introduction The ore mining industry has been successful because of technological progress and huge sums of capital investment. But new technology and plants have not come cheap. The problem now is companies will run out of money before they run out of ideas. Survival Strategies Industry survival strategies demand restructuring and new plans. Inland's prescription for the future includes: • Continued emphasis on technological improvements to upgrade pellet quality and lower costs; • Effective use of human resources resulting in employee satisfaction and improved planning and productivity; • Deliberate, well planned, and documented cost-control programs for the short- and long-term; and • Capital investments to support the first three initiatives. Technology Technological changes are not only required by the need for operational improvements, but by product quality improvement dictated by the user - usually the blast furnace operator. Established ambient measurements of pellet quality, such as tumble index, compression strength, porosity, size distribution, and chemical composition, are no longer considered meaningful in predicting pellet performance in a blast furnace. New specifications, called low temperature and intermediate temperature properties, have been recently introduced. Low temperature specifications are characterized by disintegration of pellets in the 500°C (930°F) range in the upper portion of the granular zone during the hematite-to-magnetite transformation in blast furnace stack. Intermediate temperature properties (measured by 1000°C or 1800°F) are characterized by swelling, reducibility, and compression strength after reduction, reflecting conditions in the lower portion of the granular zone of the furnace. These new parameters are being used for pellet quality evaluation at Inland, and will be introduced at its Minorca mine for more routine analysis and correlation with the pellet furnace operation. With increased emphasis on quality, effective communication between the blast furnace operator, research, and the pellet plant operator is critical. At Inland, this is accomplished through technical meetings where the opportunity is provided to solve problems, establish a common understanding on the value of quality, and develop future quality standards and programs. With the degree of sophistication in determining pellet quality as it affects blast furnace operation, the future pellet plant operator will actually be producing a custom pellet. Human Resources Technological change has been a strong point at Inland, and will continue to be. However, human resource management is equally important. Is management giving sufficient attention to employee motivation and involvement? It is a way to improve productivity, reduce costs, and enhance employee job satisfaction. The industry is beginning to understand the principles and the potential for tapping employee brainpower. The payoff can be handsome. Management has to be willing to share both information and power if participative management is to live up to its potential. It has to become more flexible and be willing to adapt to change on the human side. Management should embrace rather than fear employee involvement. Given time, joint problem solving will replace adversarial attitudes and pay dividends for both sides. Productivity and product quality will improve and new dimensions of employee job satisfaction will be achieved. But, it will not happen overnight. Attitudinal change must permeate the organization from top to bottom. This change is needed to support the working relationships and give everyone a sense of direct and meaningful involvement.

Jan 11, 1983

By Anthony B. Szwilski, Dalip Sarin, Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977, that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Feb 24, 1997

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

In its April 1991 issue, MINING ENGINEERING published a salary survey form asking for information relating to engineering and management jobs in the minerals industry. 1038 of these forms were filled out and returned, most of them being received in the magazine&apos;s offices at SME headquarters before the end of June 1991. An SME volunteer took on the task of tabulating and analyzing data from the forms, but the press of other business interfered with this work, and publication has been delayed until this issue of MINING ENGINEERING. Appreciation is extended to SME members who took the time to fill out and return the salary survey forms, and our apologies go to MINING ENGINEERING&apos;S readers for the delay in publication. Of the total number of forms received, more than 97% were from SME members. The geographic distribution of the respondents closely mirrored that of SME membership as a whole, about 50% being from the Society&apos;s Western Region, 19% from the Central Region, and 23% from the Eastern Region. About 8% were from outside the US. Average salaries for each of the four geographic areas ranged between $55,000 and $60,000, with the highest average in Eastern Region (Fig. 1). Respondents were asked to answer a number of questions formulated to determine if there are significant differences in salaries based on the type of organization for which they work. As indicated by Table 1, salary averages at mining companies do not vary markedly with the size of the company: • Large companies, defined as those having more than $1 billion in annual sales, accounted for just over 16% of the returns. Their average salary was $61,840 per year.

Jan 1, 1992

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today&apos;s feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982