Search Documents

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

By K. -J. Shou

A special three-dimensional boundary element method has been developed for the simulation of the development of fracture zone in rock mass. This approach comprises a boundary element method and a three-dimensional tessellation mesh generator. By using the tessellation generator, a set of pre-defined potential fractures is defined, and the fractures activate when the failure criterion is exceeded. This approach is justified by the reproduction of features observed in laboratory simulations of fracturing in blocks of rock subjected to compression. An attempt is then made to explain some of the attributes of fracture zone surrounding underground openings. Eine spezielle drei-Dimesionen Grenze Element Methode ist entwickelt zu simulieren die Entwicklung der Fraktur Zone in der Steinmasse. Diese Untersuchung benutzt eine Grenze Element Methode und ein drei-Dimensionen tessellation Masche Generator. Durch das Benutzen des Tessellation Generator, ein Satz der vor-bestimmt potentielle Fraktur ist festgelegt. Die Fraktur wird betaetigen, wenn das gescheiterte Kriterium ist uebersteigt und sind in dem Verscheiben-Abbrechen Element eingeschlossen. Diese Untersuchung ist von der Reproduktion der Fraktur justiert, die ins Labor beobachtet wird, um die Fraktur in der von der Kompression unterworfenen Steine zu simulieren. Ein Versuch ist gemacht, um einige Eigenschaften der Fraktur Zone um die untertageoeffnung zu erklaeren. Une méthode tridimensionelle spéciale de élément frontière a été dévélopée pour la simulation du dévélopment d’une zone fracturée dans la massive roche. Cette approche comprend une méthode de élément frontière et un générateur de maillage de la mosaïque tridimensionelle. En utilisant le générateur de mosaïque, une série des fractures potentielles predéfinies est définie avec d’une procédure de la triangulation de Delaunay. Les fractures activent lorsque le critère de rupture est dépassé et sont inclues dans les éléments du déplacement discontinuité. Cette approche est justifiée par la reproduction des caractéristiques observées dans le laboratoire, les simulations des blocs de roche fracturé et sujetés en compression. La tentative est alors fait pour expliquer quelques arttributs d’une zone fracturée alentours les ouvrages soustérrains.

Jan 1, 2003

By J. M. Descour, K. Aoki, S. Shirasagi

This paper describes the tunnel seismic reflective survey, which has been developed by the authors in order to detect the geological condition ahead of the tunnel face three-dimensionally using reflected seismic waves. In addition, the applicability and the accuracy of the result of this system has been validated by comparing with the geological observation results at the tunnel face and the result of the drill logging system, which was conducted simultaneously with this survey in order to predict the rock properties using the data acquired during drilling from the tunnel face by rotary percussion drilling. In dieser Arbeit werden Reflektionsseismische Tunneluntersuchtungen beschrieben, die von den Autoren entwickelt wurde, um die geologischen Eigenschaften am Tunnelstirnende dreidimensional an Hand reflektierter seismischer Wellen bei minimaler Unterbrechung der Arbeit zu untersuchen. Darüber hinaus wurde die Anwendbarkeit und Genauigkeit der mit diesem System erhaltenen Ergebnisse durch Vergleiche mit den Ergebnissen geologischer Beobachtungen am Tunnelstirnende sowie den Ergebnissen des Bohrlogsystems bewiesen. Das letztgenannte System wurde gleichzeitig mit dem hier genannten System eingesetzt, um die Gesteinseigenschaften mit Hilfe der Daten vorherzusagen, die beim Bohren von Probelöchern im Tunnelstirnende mit einer Drehschlagbohrmaschine erhalten wurden. Cet article décrit une méthode de prospection sismique de tunnel, développée par les auteurs, pour déterminer en 3 dimensions les conditions géologiques existant derrière le front de taille, au moyen d’étude et de mesure des ondes sismiques réfléchies dans le sous sol, et ce, avec un minimum d’arrêt des travaux d’excavation. En outre, l'applicabilité et l'exactitude des résultats de ce système ont été vérifiées, en comparant les résultats des observations géologiques effectuées au front de taille, avec ceux du log de forage qui a été effectué parallèlement à ce système, en vue de prévoir les propriétés de la roche, grâce aux données collectées au cours du forage d’un trou de sonde depuis le front de taille à l’aide d’une foreuse rotative à percussion.

Jan 1, 2003

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By W. S. Steinberg

Keywords: Pyrometallurgy, furnace, open slag bath, Evraz, Highveld In 1963, the full-scale engineering study for the development of an Iron, Steel, and Vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steel works that produced steel and vanadium-bearing slag by using a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for pre-reduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to Open Slag Bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of a higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

By M. Abdellatif

The production of a 40% Al-Ti alloy was successfully proven at the lab scale, using pure TiO2, aluminium, and lime. These tests were conducted in an induction furnace maintained at 1600?16250C. The introduction of rutile into the feed recipe resulted in an alloy containing between 0.35 and 1.10% Zr, depending on rutile to TiO2 ratio. DC arc production of the alloy was largely accomplished at 40 and then 200kW scale. These tests evaluated various metallurgical and operational factors including target slag composition, Ti-content in the alloy, co-feeding versus sequential, furnace bath depth, and rutile as part of the Ti containing feedstock. Overall, an alloy containing 24?33% Ti was consistently produced with co-feeding of the reactants and with lower taphole tapping. When rutile was added, the zirconium analysis in the alloy remained below 0.2%. The main impurity elements were iron, silicon, carbon, nitrogen, and oxygen.

Jan 1, 2009

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By G. B. Dukes

Scaling of rockpasses was problematic at Tau Lekoa Mine prior to production commencing in 1991. High horizontal stress levels relative to the host rock mass strength have been instrumental in causing the observed scaling. Scaling has been more pronounced in the deeper rockpasses and these are monitored regularly. Rehabilitation of one of the reef passes and one of the waste passes was required in the period 1999 to 2001. This paper describes the extent of the problems experienced to date as well as the rehabilitation completed.

Jan 1, 2006

By B. P. Watson, A. Carpede, W. O. Kekana, N. Fernandes, W. Theron, M. P. Mahlangu, G. Betz

The research described in this paper was done to confirm the Upper Group 2 (UG2) PlatMine peak pillar strength formula (Watson et al., 2007), which was determined from a back-analysis of failed and unfailed pillars. Underground measurements were made on a stable pillar that was loaded by firstly reducing it’s length and then by mining the surrounding pillars until pillar failure took place. The pillar was instrumented with suitably positioned strain cells and closure meters, which allowed both the average pillar stress and strain to be determined. The paper describes the methodology applied to identify a suitable position for the instrumentation, as well as the results. A stress/strain curve is presented for a UG2 pillar with a w/h ratio of 2.0, at Booysendal Platinum Mine. The measured pillar strength was similar to the predicted strength using the PlatMine pillar strength formula for UG2 pillars. The PlatMine formula has been successfully implemented on Booysendal Platinum Mine, and about 3 670 pillars have been cut without a single failure. An additional revenue of US$1.3 billion was calculated for the 25-year life of the mine as a direct result of the improved pillar design, given the January 2020 platinum group metals basket price. An extended life of mine and better mining efficiencies will also be realized.

Aug 1, 2021

By Ravichandar. D., K. B. Nagashanmugam, M. S. Pillai

"Blast furnace performance depends strongly on the coke reactivity index(CRI) and coke strength after reaction (CSR) properties. An innovative and cost-effective method, known as the Salem Box Test, has been developed to prevent the mass production of inferior coke unsuitable for blast furnace use. This method consists of coal carbonization on a micro-scale and involves charging approximately 18 kg of coal blend in a stainless steel box, carbonizing it together with coal cake in the plant coke ovens, and testing the coke produced for CRI and CSR to determine its suitability for blast furnace use. Only coal blends that yield coke with CRI <25% and CSR >64% are permitted for mass production, and other coal blends are either rejected or the blending ratios adjusted in an attempt to upgrade them. The experimental results reveal that, for a given coal blend, the quality of coke produced by the Salem Box Test is comparable with that produced by bulk production, indicating that the test is acceptable as a screening tool for regular use. The present paper describes the methodology and application of Salem Box Test to predict the suitability of coke for blast furnace use at JSW Steel Limited, Salem Works (JSWSL), and illustrates its advantages in adjusting the coal blending ratio to produce superior coke, in detecting coal contamination, and in preventing bulk production of inferior coke."

Jan 1, 2015

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By J. A. Cox

The Ashanti mine is located within the Lower Proterozoic Birimian of Ghana, and covers a concession of 474 square kilometres at its Obuasi operations which comprise large scale underground, surface and tailings treatment facilities. The mine had operated for a century at the end of 1997 and had produced nearly 25 million ounces of gold, a significant proportion of which came from the underground operations. This paper covers the strategy under which exploration for both surface and underground mineral resources was instrumental in enabling the expansion programme to go ahead together with the methodologies and results that have developed in the exploration area over the last five years. Within capital expenditure constraints, the objective on surface is to replace oxide depletion with a secondary objective of discovering new sulphides in areas other than the main trend. In the underground, the exploration strategy is directed at replacement of both underground and surface sulphide depletion, minimising finding costs and assisting the development of long lead time infrastructure. The exploration application describes the methodologies in use for both surface and underground exploration that have been developed in recent years in conjunction with a description of a major review conducted in 1995/96 of the exploration database using an integrated approach, geochemistry, geophysics, remote sensing and structural geology. A revisit of soil geochemical data in particular, and modification of exploration methodology led to the success in finding relatively significant new oxides in 1997.

Jan 1, 1999

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009