Search Documents

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By E. L. Thyse

Keywords: Pyrometallurgy, converter, nickel, matte, distribution Metallic elements occupy a wide range in granulated nickel converter matte phases. The distribution of these metallic elements, particularly during crystallization path events, appears to be poorly understood. The present study serves to investigate the distribution of Fe, Co, Ni, Cu, and Pb between nickel-sulphide, copper-sulphide, and alloy phases. A novel combination of thermo-chemical modelling, electron microscopy, and electron probe microanalysis was applied to understand crystallization path events and the associated metallic element distribution. This study has demonstrated that major Ni incorporated during copper-sulphide crystallization would serve to mobilize minor Co towards distribution in copper-sulphide phases. In addition, solid solution substitution of Cu by Ni is manifested by compositional zoning of copper-sulphide phases. The role played by Ni during alloy crystallization suggests that minor Co was also mobilized, along with an increase in principal Ni. Fe, by contrast, seems to be incompatible with principal Ni. In addition, solid solution substitution of Ni with PGEs and Cu is manifested by compositional zoning of NiCu-alloy phases.

Jan 1, 2011

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By M. Visser

Keywords: Pyrometallurgy, furnace, ferrochrome, Samancor, ferrochrome process Samancor Chrome has been, and continues to be, a major player in ferrochromium production. The company has a proud history and possesses benchmark technology and operations. Currently five business units are operating: two sets of mines and three smelter plants. Samancor Chrome produces around one million tons of charge chrome annually. Chrome ore, intermediate-carbon ferrochrome, and low-carbon ferrochrome, form part of the portfolio. Electrode paste is also manufactured through a joint venture with Highveld Steel and Vanadium. Samancor Chrome has a balanced approach towards operational strategy, and has entered into a number of joint venture partnerships. Through its access to quality raw materials, knowledge, and experience of various production technologies, and its strategic abilities, Samancor Chrome is well positioned to reap the benefits from opportunities in the current and future industry context.

Jan 1, 2006

By E. Pizarro, A. Videla, G. Compan

One of the main problems related to mining investment decisions is the use of accurate prediction models. Metallurgical recovery is a major source of variability, and in this regard, the Chuquicamata processing plant recovery was modelled as a function of geomining-metallurgical data and ore characteristics obtained from a historical database. In particular, the dataset gathered contains information related to feed grades, ore hardness, particle size, mineralogy, pH, and flotation reagents. A systemic approach was applied to fit a multivariate regression model representing the copper recovery in the plant. The systemic approach consists of an initial projection of the characteristic grinding product size (P80), based upon energy consumption at the particle size reduction step, followed by a flotation recovery model. The model allows for an improvement in the investment decision process by predicting performance and risk. The final geometallurgical model uses eight operational variables and is a significant improvement over conventional prediction models. A validation was performed using a recent data-set, and this showed a high correlation coefficient with a low mean absolute error, which reveals that the geometallurgical model is able to predict, with acceptable accuracy, the actual copper recovery in the plant.

Jan 1, 2015

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

1. OPLEIDING IN INGENIEURSWERK VIR IN G ENIEURS- IN -OPLEID IN G 1.1 llegistrasie as Ingenieur-in-opleiding 'n Gegradueerde ingenieur wat in 'n eksamen geslaag het wat die Raad erkenl, is registreerpaar as 'n ingenieur-in-opleiding kragtens die Wet op Professionele Ingenieurs2. Aansoekvorms kan van die Registrateur verkry word. Mineral processing congress The XIIIth International Mineral Processing Congress is to be held in Warsaw from 4th to 9th June, 1979. Seeing that by products and co-products are becoming of increasing importance in mineral processing operations, the theme of the Congress is to be the 'Treatment of Raw Materials with Total Utilization of All Constituents'.

Jan 1, 1979

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By H. Immink

Keywords: Kyoto Protocol, carbon credits, global warming, energy, auditing Climate change is nowadays being taken increasingly seriously, and the link between global warming and the carbon dioxide released in the generation of energy is coming under increasing scrutiny. The Kyoto Protocol was signed in 1997, after five years of negotiation. So far, about 84 countries have ratified this agreement, under which terms developed countries have strict targets linked to their 1990 level of emissions. However, ?greenhouse gas? (such as carbon dioxide) emissions continue to rise alarmingly. According to the World Resources Institute, greenhouse gas emissions in the USA increased 13% from 1990-2002, while Australia recorded a 22% increase. In contrast, the European Union, a Kyoto signatory, has seen a small decline in its emissions during the same period. This is led by the UK and Germany, who reduced their emissions by 15% and 19% respectively. The concept of ?carbon credits? provides a funding mechanism for companies in the developed world to compensate for some of their CO2 emissions by paying companies (trading credits) elsewhere in the world to undertake projects to bring about reductions in emissions. In the southern African mining industry, it will be possible to get refunded for undertaking voluntary emission-reduction projects. Concern about the environment is creating business opportunities. A preliminary calculation has shown that various projects in South Africa (those in the pipeline, with quite a high likelihood of coming off) could earn a combined total of about R2.5-billion, under the initial phase of the Kyoto Protocol's carbon-credit scheme, which allows developed-country companies to trade credits with developing countries. A number of local companies are planning projects that could comply with the Clean Development Mechanism (CDM), in which they will implement techniques to achieve certified emission reductions (CERs) of greenhouse gases. In order to prevent abuse of such a system involving vast sums of money, vigorous audits need to be carried out. A company has to prove it has made real changes and is not simply conducting business as usual under a cloak of claimed environmental improvements. PricewaterhouseCoopers has applied to become one of only a few international agencies that will be accredited to conduct validation and verification of the credits, by auditing what is called the ?designated operational entity?. An independent validator needs to confirm that the project meets the strict requirements of the Kyoto Protocol. The company has to demonstrate that it?s not business as usual. So, if you refurbished every five years, the next refurbishment is not a good CDM project, unless you can demonstrate that you will do something beyond the maintenance - that is what can be registered. So, Kyoto intends to get additional projects going, and the money for that is actually quite good - prices of 14 euros per ton of carbon dioxide not emitted have been seen. The price depends on who takes the risk for non-delivery if a project doesn?t deliver the emission reductions on time. The highly energy-intensive South African mining industry is heavily dependent on coal. There should be many opportunities for the pyrometallurgical industry to come up with creative ideas to reduce emissions, and there is now an additional financial incentive to encourage this. Companies can actually get money in return for doing these types of projects, in addition to the contribution to corporate social responsibility.

Jan 1, 2006

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

By P. Amponsah-Mensah

Dilution of ore has a major impact on economics of a mine. The magnitude of dilution depends on mining method, stope dimensions, reef and host rock quality, wall support and drilling accuracy. The main contributing factor is the presence of very weak graphitic shear band of varying thickness in and around the reef. The reef, at Obuasi, is generally steeply dipping and open stoping is the predominant mining method. The stability of the stope walls limits the stope dimensions. Various options for allowing larger stopes for higher productivity and limiting dilution are analysed. The most economic way is to reinforce the walls with systematic cablebolt supports. This option does not only add the support cost but also requires additional cost of access development. These conflicting requirements are continually being optimised at the mine for the economics of dilution control. La dilution du minerai à un impact majeure sur l’économie d’une mine. La quantité de matériel diluant le minerai dépend de la méthode d’extraction, de la dimension des chantiers d’abattage, de la qualité du filon et de la roche mère, du support des épontes et de la précision du forage de production. Le facteur principal qui contribue à la dilution est la présence d’étroites zones cisaillées qui contiennent du graphite ayant différentes épaisseurs à l’intérieur et autour du filon. Le filon, à Obuasi, est généralement à fort pendage et la méthode d’abattage principale est par chantier long-trous. La stabilité des épontes est le facteur qui détermine la dimension des chantiers d’abattage. Differentes options ont été analysées de façon à permettre de plus larges chantiers de manière à augmenter la productivité tout en limitant la dilution. Le moyen le plus économique est de renforcer les épontes avec des cables d’acier cimentés forés de façon systématiques. Cette option n’augmente pas seulement les coûts de support mais aussi les coûts de développement. Ces besoins contradictoires sont continuellement revisés à l’opération afin d’optimiser l’économique par le contrôle de la dilution. Verdünnung des Erzes hat eine spürbare Auswirkung auf die Ekonomie einer Grube. Die Größe der Verdünnung hängt von gewinnenmethode, von den Stopemaßen, von der Reef- und Wirtsfelsenqualität, von der Wandunterstützung und von der bohrengenauigkeit ab. Der beitragende Hauptfaktor ist das Vorhandensein einer sehr schwachen graphitic Scherbandes unterschiedlichen Stärke in und um der Reef. Der Reef, bei Obuasi, taucht im allgemeinen steil ab und geöffnete Aufstemmung ist die überwiegende gewinnenmethode. Die Stabilität der Wand begrenz die Stope grösse. Verschiedene Wahlen für das Erlauben der größeren Stopes für höhere Produktivität und das Begrenzen von Erzesverdünnung werden analysiert. Die ökonomischste Weise soll die Wände mit systematischen Kableankerbolzenunterstützungen verstärken. Diese Wahl addiert nicht nur die Kosten der Unterstützung aber erfordert auch zusätzliche Kosten fuer Zugangsentwicklung. Diese kontroversen Anforderungen werden fortwährend an der Grube analysiert um die Verdünnungkontrolle zu optimieren.

Jan 1, 2003

By M. van Schoor

The bulk of the world?s platinum production originates from the Merensky and UG2 reefs within the Bushveld Complex, South Africa. Both the Merensky and UG2 reefs are disrupted by faults, dykes, potholes and iron-rich ultramafic pegmatite bodies (IRUPs)?features that impact negatively on production, planning and safety. It is therefore advantageous to know of their presence and geometry ahead of mining. To date, no geophysical technique has been successfully applied to the routine mapping of mine-scale potholes and IRUPs. These disruptive features may vary from a few metres to several tens of metres in diameter. In this paper the applicability of in-mine electrical resistance tomography (ERT) to map potholes and other disruptions to the continuity of the Merensky and UG2 reefs ahead of mining is demonstrated using two case studies.

Jan 1, 2005

In constructing a financial model of a project significant effort is expended on capital and operating cost estimation, commodity price forecasts, and choice of discount rates while uncertainty in the primary input, the reserve, is often completely overlooked. The aim of this paper is to highlight the impact of uncertainty in the resource/reserve estimation process on the assessment of the financial performance of a project. Four qualitative processes have an impact on resource/reserve uncertainty. These stages are: 1.Ore definition 2.Geological interpretation 3.Resource estimation 4.Ore reserve estimation and mine planning. Each stage contains a number of tasks that may be considered as key performance activities (KPAs). Optimizing the manner in which these KPAs are completed can remove a great deal of uncertainty and error from the resource/reserve process. Examination of these KPAs within a company can also provide an insight to the quality of the information underlying the project. This will allow the company to identify any shortcomings in the data and to assess the resulting risks (Gilfillan, 1998). A hypothetical financial model based on a gold operation has been used to estimate the potential effect of resource/reserve uncertainty on revenue. Monte Carlo simulation has been employed to simulate a number of hypothetical scenarios: 1.a base case scenario which assumes no major errors or biases, but contains realistic margins for uncertainty that would exist in any project where work is being completed to the limit of best endeavours 2.a poor sampling scenario which assumes poor sampling practice and lack of understanding of sample preparation 3.a poor resource estimation scenario which assumes poor modelling and inappropriate choice of interpolation technique, and 4. a ?typical? scenario which represents a project where the majority of KPAs are not performed as best as they could be. The results show that realistic uncertainty ranges can generate changes in the estimate of potential revenue of plus or minus 30%.Therefore, it is important to allow for errors in these processes in any financial analysis or feasibility study. It is recommended that, when building a financial model, are view of relevant resource/reserve KPAs be carried out and appropriate ranges for uncertainty be applied to provide a range of potential outcomes. These outcomes can then be factored into the detailed cash flow analysis in order to ensure that technical uncertainty is built into financial decisions.

Jan 1, 1999