Search Documents

The vast majority of the roughly 100 million rock anchors installed in mines in the USA each year use resin cartridges1. About 4.5 million of these bolts are installed using a mechanical shell in addition to the resin to create an active (pre-tensioned) bolt. Over 1 million of the bolts are passive cable bolts and typically have an effective grout length of 1.2 m, regardless of the cable length, which could be as long as 6 m. The successful performance of the resin grouted bolts depends on several parameters, including the annular gap between the bolt and hole wall, which should be relatively small, ideally from 3 mm to 5 mm. This requirement, combined with the high viscosity of the resin, produces a high back-pressure that can cause the bolt being installed to buckle or not be installed to standard. It is this back-pressure that limits the effective grout length with passive cable bolts and causes the mechanically anchored bolt failures (typically called ?spinners? where the mechanical shell does not anchor). This creates potentially unsafe conditions and wastes time and money. A purpose, built rig was used to mimic underground installations and record the back-pressures during full scale applications in the laboratory. This information was used, and is still being used, to reduce the failures and sub-standard installations by producing improved designs. In addition, a flow model was calibrated that can act qualitatively to estimate the back-pressures and can be used as a crude screening process before full scale prototypes are built and tested. To date, the results obtained have been used to stop the use of a mechanical shell due to the proven higher rate of failures. A new, improved mechanical shell is being field tested and another system is underdevelopment. The use of the rig is therefore ongoing to develop improved mechanical anchor systems. It is too early for real data; however, anecdotal evidence seems to indicate that significant improvements can and will be made.

Jan 1, 2011

By A. F. Khan

The CSense advanced process control (APC) solution?s main objective was to improve the stability of the pH in the first stage leach process thereby improving nickel and iron extraction efficiencies and reducing the base metal (BM) content in the platinum group metals (PGM) concentrate. By improving the stability of the control of the pH on the first stage leach it had the corresponding effect of improving the Ni extraction efficiency by 0.5% and the Fe extraction efficiency by 3.3%. The system relieved the operators of many decisions that were virtually impossible to make given the complex, variable and real-time nature of the processes in their charge. On the operational side, the operators understand the APC system and they trust it. Another benefit is the reduction in pH peaks in the autoclave, which can oxidize certain elements whereby they become difficult, if not impossible, to leach. These elements go right through the process and end up contaminating the PGM solids, with the result that the entire batch has to be recycled through a lengthy and costly processing pipeline.

Jan 1, 2009

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By E. van Steen, G. M. Leteba

Optimizing the catalytic performance of multimetallic nanoparticle (NP) catalysts demands a concrete understanding of their design, while preferentially deploying wet chemical synthesis procedures to precisely control surface structural properties. Here we report the influence of reductants such as hydrogen-rich tetrabutylammonium borohydride (TBAB) and carbon monoxide-rich molybdenum carbonyl (Mo(CO)6) on the shape and morphological evolution of Pt-based binary (PtNi and PtCo) and ternary (PtNiAu and PtCoAu) nanostructures derived from a homogeneous solution of aminebased surface active agents (surfactants) in a high boiling point solvent. We successfully synthesized nanostructures exhibiting well-defined and composition-controlled surfaces deploying a one-pot synthetic approach. The development of the surface properties was, however, observed to be alloyspecific. The resultant highly monodisperse alloy NP with narrow size distributions and facet-oriented surfaces are expected to display enhanced functionality as catalysts for utilization in specific chemical reactions.

Jun 1, 2021

By K. Dewar

The catalytic converter industry is composed largely of global multinational manufacturers who supply to vehicle manufacturers (original equipment manufacturers ? OEMs) from facilities strategically located internationally, including plants in South Africa. The South African catalytic converter production facilities were established at the request of the OEMs and commenced manufacture in the early 1990s. This near 100 per cent export focused industry exists in South Africa because of the incentives offered by the Motor Industry Development Programme (MIDP), which ultimately provide the OEM with import duty rebates. The South African catalytic converter industry is a complex vertically-integrated supply chain with a local content in excess of 85 per cent, substantially more than any other exported automotive component. The industry remains one of the very few downstream manufacturing industries where South Africa has a significant global footprint. This is even more important when it is considered that this industry is the key end-user for two of South Africa?s most important mineral resources, namely platinum group metals (PGMs) and chromium, and is in an industry which will see massive global growth as the developing nations of the BRICs grow their auto industries. In over 15 years of existence in South Africa, the catalytic converter industry has achieved remarkable growth, averaging compound growth in the region of 14 per cent per annum. The industry is the highest contributor to automotive component export revenue. South Africa holds >8 per cent% of global PGM reserves. During 2011, South Africa supplied 59 per cent, 29 per cent, and 72 per cent of the global demand for platinum, palladium, and rhodium respectively, as well as over 50 per cent of the global chromium demand. Global autocatalyst production remains the largest consumer of PGMs, and South Africa alone beneficiated 15 per cent of locally mined PGMs in the production of catalytic converters ? all is converted from PGM sponge (powdered metal) into PGM solutions for coating onto catalysts. Beneficiation of PGMs also takes place via the production of jewellery and electronic goods; but compared to catalytic converters, this volume is negligible. The industry is also the largest consumer of locally produced stainless steel (>50 000 t/a), exceeding 38 per cent of local consumption. The industry is a substantial generator of highly skilled employment, with over 5 000 direct jobs (excluding OEMs and stainless steel manufacture) and an estimated more than 30 000 indirect jobs resulting from upstream and side-stream suppliers. The industry places a high focus on skills transfer and development, with all companies providing high-tech training and education both locally and overseas. The industry has invested in excess of R5 billion in plant, equipment, people development, and process development over the last 15 years to support transfer of production and new technologies to South Africa. This has resulted in significant skills development in the support industries as well as within the catalytic converter industry. The current projections for local PGM beneficiation via catalytic converters reflect a downward trend as a result of production being moved to other global locations due to uncertainty around changes to government incentive programmes. The industry is currently capacitated to support 23.7 million units per annum. During 2011 it utilized about 70 per cent of this capacity, but forecast projections suggest that this will be at 46 per cent of this level by 2016. At full capacity the industry would represent 19 per cent of global autocatalyst production compared with the current 13 per cent in 2011. The industry believes that there is potential to make South Africa the preferred location for catalytic converters worldwide, given suitable support from the mines and Government.

Jan 1, 2012

By H. W. J. P. Neomagus, J. R. Bunt, D. L. Botha, N. T. Leokaoke

Coal briquetting traditionally makes use of high-dosage, nonpolymeric binders (such as coal tar pitch or molasses) or polyvinyl alcohol (PVA) at low dosages for the binding of fine and ultrafine coal. Due to constraints associated with the manufacturing and cost of PVA-bound briquettes, a novel polyacrylic binder was developed that could possibly be added in low dosages at room temperature. A set of formulations of two polyacrylic components (components A and B) was developed, from which an optimal binder mixture was determined. This formulation comprises 40wt.% component A and 10wt.% component B with a 0.04wt.% cross-linking additive, and the balance water. The uniaxial briquette compressive strength was used to obtain the optimal binder mixture. The binder mixture was added to the coal powder in dosages from 0.1 to 1.2wt.%. Mechanical tests and thermogravimetric analysis in an oxidized environment at a maximum temperature of 930°C were conducted. Binder-bound briquettes were compared to binderless briquettes and PVA-bound briquettes. Briquettes made from the polyacrylic formulation had uniaxial compressive strengths double that of the binderless briquette yield strength, as well as the minimum recommended compressive strength of 0.375 MPa. The organic binders did not affect the combustion of the briquettes, since the results compared well with the binderless briquettes. The polyacrylic formulation is considered to be a possible substitute for PVA in terms of mechanical and thermal properties and raw material cost.

Mar 1, 2021

By D. Amariei, G. Bartolacci

Preconcentration of precious and base metal ore types is becoming more relevant with the discovery, the development and the operation of many lower grade deposits around the world. Ore preconcentration designates an operation consisting of sorting an ore to reduce the quantity of waste material sent to the concentrator. It can be seen as rejecting waste material as much as possible, without compromising the recovery, or as the recovery of as much valuable metal as possible into an optimum mass yield. Benefits of preconcentration are multiple: grinding energy savings, costs reduction, lower environmental footprint, extension of the reserves, etc. However, all of these benefits do not apply simultaneously and are not applicable to each ore type. Technologies employed for preconcentration are highly dependent on ore properties, especially on the particle size at which the gangue is liberated. Thus, from coarser to finer particle sizes, technologies such as screening, ore sorting, gravity separation (Dense Media Separation (DMS) and jigs) and coarse flotation could be used for the rejection of liberated gangue. The difficulty starts when a benchmark is needed to select a suitable technology, especially for low-grade gold deposits. This paper presents the challenges of comparing lab-scale technologies (DMS versus jig) for gold preconcentration. The experimental data will show to what extent comparing two lab-scale gravity technologies for gold preconcentration can be challenging. An attempt to evaluate the energy savings by assessing the hardness of the tailings after gravity separation will also be presented. Keywords: Challenges in gold preconcentration, gravity separation, jig, dense medium separation

Jan 1, 2020

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By C. Musingwini, A. S. Nhleko, M. J. Mahase

"In an environment like the mining industry, which is characterized by different stakeholders with multiple objectives, multi-criteria decision analysis (MCDA) is a useful approach for optimal decision-making. The application of MCDA techniques in the mining industry has predominantly been in mine planning and related problems, although no comprehensive survey has previously been undertaken to establish the application trends. A survey of the use of MCDA techniques was therefore conducted using case studies from the literature. It was noted that often two or more methods are applied to the same problem in order to increase confidence in the solution derived. As the number of criteria and alternatives increases, some methods become inefficient. A combination of the analytic hierarchy process (AHP) method with other MCDA techniques was the most frequently used approach, indicating the efficiency of the AHP method, especially when evaluating problems with more criteria and fewer alternatives. A combination of fuzzy theory with AHP or other methods incorporates uncertainty. The findings from the survey will benefit users applying MCDA techniques to solve mine planning and related problems.IntroductionA country’s natural resources serve the needs of different groups of people within the country. These different groups are collectively known as stakeholders (Herath and Prato, 2006). Stakeholders have different needs, preferences, and expectations, which describe and define the criteria to be considered in decision-making. The options available as solutions describe the alternatives in decisionmaking theory. The criteria and alternatives have to be evaluated simultaneously when making decisions, and this is when multicriteria decision analysis (MCDA) techniques become invaluable (Herath and Prato, 2006) because the human mind is considered to be limited when solving complex and intangible problems with several criteria and alternatives (Saaty, 2007). MCDA techniques belong to a broad group of techniques called multi-criteria decision-making (MCDM) techniques. The other group of techniques within MCDM comprises the multi-objective decision-making (MODM) techniques. MODM techniques are generally used to solve problems with an infinite number of alternatives, while MCDA techniques are generally used to solve problems with a finite number of alternatives (Musingwini, 2010)."

Jan 1, 2016

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012