Search Documents

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

By D. G. Millenbruch

An account is given of a four-phase system for the appraisal of a mineral project while it is still in the exploration stage, and for continual consideration of a favourable appraisal until the production stage is reached. There are ten stages from the idea of a likely project to the production stage, and all the staff that are eventually to be concerned with the development of the project are involved at an early stage.

Jan 1, 1979

By D. G. Wymer, A. G. du Plessis, N. C. Joughin

The use of a dense hangingwal-support configuration extending right up to the face would enable greater levels of safety and productivity to be achieved in stopes, and becomes a practical proposition if water jets are used for stope cleaning. Such an arrangement opens the way for extending the use of water hydraulic power to the whole stoping operation. This, in turn, can provide further productivity benefits and significant savings in working costs. With al the necessary equipment being available, such a system could be introduced immediately, although the designs of props and rockdrills are not yet ideal.

Jan 1, 1989

By D. G. Krige

The problem of a realistic investment analysis for a new mining venture that sells its products on the international metal markets IS studied against the background factors, firstly, of different inflation rates between the countries hosting the mines and those. hosting the metal markets; and, secondly, of the changing pattern of currency exchange rates between such countries. The purchasing-power parity theory is used to establish a pattern of relationship between these two factors, and to develop a more logical approach to the long-term forecasting of metal prices in the currency of the country in which the mine is situated.

Jan 1, 1979

By E. J. Maunders

This paper describes briefly a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25000 to 70000 tons of uranium, proves to be very data-sensitive.

By M. H. Moys, J. Engelbrecht, N. Terblanche

Interface levels in flotation columns are generally measured with the aid of a pressure-sensitive Instrument, e.g. a differential-pressure cell. This paper criticizes the use of this type of measurement, and discusses other methods that are claimed to give more accurate measures of interface levels. The paper focuses on the development of methods based on the measurement of conductivity across the froth-slurry interface. These are often sabotaged by variations in the conductivity of the feed slurry, particularly when the pH of the slurry IS being controlled, e.g. In sulphide flotation. Methods of improving the accuracy and reliability of this technique are described. The result IS a robust, easy-to maintain level-control scheme that successfully rejects large disturbances in plant operation (including a 5:1 change in slurry conductivity) while controlling levels to an accuracy of I 4 cm.

Jan 1, 1992

This paper describes the extraction of gold, as the anionic aurocyanide complex, from solution by strong- and weakbase anion-exchange resins. The effects, on the rate of extraction and the loading capacity for gold, of parameters such as pH, temperature, ionic strength, agitation, and the presence of competing anions are reported. The elution and regeneration of strong- and weak-base resins will be examined in a second paper. A third paper in this series will present the results of several smallscale pilot-plant investigations carried out with strong- and weakbase resins In cyanide pulps from various South African gold mines, and will compare the metallurgical performance of resin-In-pulp with that of the carbon-in-pulp process.

Jan 1, 1984

By D. Yu Pleev, V. G. Krivolapov

Mines of Southern Kuzbass working out, basically, coal formations of flat seams. Seams, as a rule, are inclined to self-ignition. Detection at early stages of the centers of endogenous underground fires has great value for safe conducting mountain works. One of methods of detection of an early stage of underground fires in the worked out space is the method of superficial radon survey. In the report the method is de-scribed and examples of superficial radon survey on concrete layers are given.

Jan 1, 2003

ERRATA-AUTHOR'S REPLY IN SEPTEMBER, 1970, JOURNAL: PAGE 52 I. Left half of the page, 4th paragraph, fifth line from the bottom: for 22 / 5 1/2 %, read 22 / 5 1/2 %. 2. Right half of the page, fifth paragraph from the bottom, third line from the bottom: for N(l - p), read N(1 - p)x. 3. Right half of the page, fourth paragraph from the bottom, second line: for: at time t after time zero, read: at time x after time zero. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By I. Wigden

This paper discusses system integration and installation of High-Tec systems in underground mines. ABB has the capability to be a System Integrator and co-operates with partners in different areas of technology. Today it is difficult to find one Company that is responsible for the complete Automation System. The design of the system is also dependent on the caving procedure that is currently being used in mines. Most of the engineering must be done during the feasibility study and the design phase. Any mistakes made during these phases will be costly to rectify in the commissioning phase. The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and the importance of integration with the people component. Most of the experience and discussions in this paper are from different technologies that have been developed in Scandinavia and adopted from LKAB in Kiruna. The author of this paper was responsible for the Automation projects in Kiruna Mine during1994 - 1999. These projects include: • Broadband communication of data, audio and compressed video in one data stream. • Control System for Haulage -1045m • Automation of Load Haulage and Dumping machines (LHD) • Control of Production Drilling Rigs from a Central Control Room.

Sep 1, 2001

By G. E. Blight

Several aspects of the behaviour and properties of backfills consisting of cemented cyclone underflow tailings are illustrated by means of examples, and guidelines are given on the optimization of the performance of cemented fills. The stretch characteristics of the geofabric used to contain freshly placed backfill are described, as well as the relationship between these characteristics and the forces acting on retaining barricades. The properties required to achieve a self-supporting, stable free face in cemented backfill are explored, and a graphic relationship between stable height and shear strength is presented and compared with that for uncemented (classified) tailings. After a description of the characteristics of Witwatersrand quartzite gold-tailings backfill and commonly used cements, the process of drainage and air entry into backfill is outlined. Following this, the early-age gain in strength and the shear-strength characteristics, as well as the compressibility characteristics of cemented backfill, are described. Two phenomena that are potentially damaging to cemented backfill are seismic effects (or blasting acceleration) and the closure that takes place during the curing of cement. Investigations show that neither of these phenomena is actually significantly deleterious to gold-tailings backfill: liquefaction does not Occur as a result of seismicity, and hydration of cemented fill is not significantly impeded by closure.

Jan 1, 1996

A powerful, interactive metallurgical process simulator for use on micro- computers has been developed in the Department of Metallurgy and Materials Engineering at the University of the Witwatersrand. MICROSIM presently allows simulation of all ore-dressing flowsheets and a selection of hydrometallurgical unit operations, and is extendable to all such processes. MICROSIM is written in Pascal. This modern language provides very versatile data structures which can be effectively used to solve the major problem in generalised simulation programs, namely storage and transmission of data relating to liquid and solid phases. Dynamic memory allocation allows optimal utilisation of computer storage space. The simulator utilises very efficient precalculation algorithms that determine the tear streams for optimal sequential modulator calculation convergence. Microcomputer graphics simplifies flowsheet specification, and form-filling data capture with supplied default values eliminate most common input errors.

Jan 1, 1987

By Mike Rogers

Platinum production in Southern Africa amounted to 80% of world production in 2005with a small increase from 5 117 000 ounces to 5 275 000 ounces. For the seventh consecutive year the platinum market is on course to record a moderate deficit in supply. This is reflected in the price increase from a trading range US$860 to US$880 in June 2005 to an excess of US$1 200 in September 2006. Southern Africa, with its extensive platinum reserves, will continue to be the dominant platinum producer and has a number of new mines in an advanced stage of planning. The slogan ?Platinum Surges Ahead? was selected to describe the exciting and vibrantnature of all aspects of platinum mining, beneficiation and marketing. This conference will cover these aspects from exploration and orebody delineation, through mine design, development and operation to mine closure; mineral beneficiation, marketing and compliance with the Mining Charter will also be subjects for discussion and debate. It is also anticipated that the issue of overall increases in productivity, through the introduction of technology, will demonstrate Southern Africa?s status as a premier mining district. It is my pleasure to welcome delegates from abroad and locally, on behalf of the SAIMM, to the Second International Platinum Conference ?Platinum Surges Ahead?. I trust that you will find the proceedings informative and value adding and will participate in the discussions and debate in order to obtain maximum benefit from the conference. I am sure that the post-conference tours will be interesting and of great benefit to participants. Finally, a big word of thanks to the members of the Organising Committee, the management and staff of the SAIMM, and to our willing sponsors, without all of whom this conference would not have been possible.

Jan 1, 2006

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

By A. Muller

The magnesia-carbon refractories used in the ConArc process experience severe wear as a result of the varying slag composition during the blowing phase. This work determines the basicity range in which minimum as well as maximum refractory wear was experienced by the magnesia-carbon refractories during service. In order to determine an optimum slag composition, the crucible test in an induction furnace was used. The magnesia-carbon refractory bricks were cut into cylindrical crucibles to which a synthetic slag in the form of pellets was added. The basicity (B2) of the slag was varied from 0.5 to 3. Tests were done at 1 600°C for one hour. Apart from the crucible test in an induction furnace, visual inspection and SEM analysis were also done to investigate the corrosion mechanism. FACTSage® predictions about the interaction between refractories and slag were also done. These predictions were compared to the actual results attained. It was found that the extent of corrosion by slag attack decreases as the basicity increases. The most severe corrosion of the MgO-C refractories occurred at a basicity of 0.5 whereas the optimum basicity is above 2.0. SEM analysis indicated severe slag attack at the lower basicities with no visible refractory-slag interaction at higher basicities. TheFACTSage® predictions supported most of the actual findings. Keywords Magnesia-carbon, ConArc, blowing phase, slag resistance, induction furnace, crucibles.

Jan 1, 2011

By J. R. Dixon

Gold mining has been undertaken in South Africa for more than a century. A great proportion of that mining has been from the Witwatersrand Basin; a geological phenomenon that has few parallels throughout the world. It has produced some 47 000 tonnes of gold mainly from underground mines, many of which have been truly world class gold mines. The gold mines of the Witwatersrand Basin have dominated world gold production from their inception and their production has been one of the cornerstones of the development of South Africa as a whole. The mines have some very specific characteristics; their sheer size, the depth of extraction, the nature of the orebodies, and their labour-intensive methods. The mines have also been part of the Mining House concept-a concept unique to South Africa. South African production has declined from a maximum of 1000 tonnes in 1970 to 470 tonnes in 1997. This, as a percentage of western world production, has declined from a maximum of 79 per cent (in 1970) to 21 per cent of world production (in 1997). The nineties' have seen South Africa and its mining companies move onto the world stage and face the harsh realities of having to compete in all spheres of business with their aggressive counterparts principally in Australia, Canada and the USA. The fight is for investment funds with the owners looking for the best returns on their money. In his address Roger Dixon will examine the current situation in the gold mining industry and examine the competitiveness of the mines of the Witwatersrand Basin compared with their peers worldwide. He will also discuss some of the fundamental challenges facing South African gold mines in the areas of legislation, technology, industrial relations, and health and safety. The environment in which the mines operate has changed radically in recent years and their ability to respond to these challenges will determine their future existence.

Jan 1, 1998

By I. C. R. Gilchrist

A principal requirement in the design of a backfill transportation pipeline is the accurate prediction of the values of key slurry flow parameters. Input variables, such as particle size and solids concentration, are usually determined by the load-bearing requirements of the placed fill. It is therefore necessary to identify the optimum conditions of transport for a particular combination of input variables. This paper critically reviews the methods available to predict the values of flow parameters in slurry pipeline systems in the light of experimental data generated at a test facility. Particular reference is made to rod milled waste and deslimed tailings transport systems and, in the case of the former, it is shown that both pumping and load-bearing requirements can be optimized.

Jan 1, 1988

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best `grade descriptor' is discussed.

Jan 1, 2007

By G. R. J. Cooper

In recent years attempts have been made to develop software packages for shallow seismic refraction data analysis. In most cases, mainframe computers were used which were generally non-interactive, did not support graphics and were unfriendly to operate. With these facts in mind, a user-friendly interactive processing package written in PASCAL has been developed for the IBM PC. The package allows the following operations to be performed. (1) data tying, equalisation of reciprocal and common shot times; (2) overburden velocity analysis; (3) refraction leg identification on time-distance plots; (4) elevation correction of refractor data; (5) forward and backward phantoming; refraction leg extrapolation; (6) 'bedrock' velocity analysis; (7) 'time-depth' plot computation; (8) depth calculation. Numbers (6) - (8) above involve Palmer's generalised reciprocal technique of refraction data interpretation. The program is extremely flexible and makes much use of interactive high resolution graphics and 'popup' onscreen menus. The velocity analysis sections have statistical routines built in to provide error estimation. The programs allow data interpretation to take place in the field with a portable microcomputer while the data are still being collected; this is obviously not possible with any cumbersome mainframe-based software. Hence it becomes possible to see the effects of varying the data collection parameters (such as geophone spacing) upon the resulting interpretation and so enable adjustments to be made where necessary. Hard copies of the data may be obtained at all stages of the interpretation process using a small (A3) plotter, or the graphics may be dumped to a dot- matrix printer if a suitable plotter is not available.

Jan 1, 1987

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007